Fortinet FortiCam FD50 Bedienungsanleitung
FortiCam FD50
QuickStart Guide
February 9, 2021
Copyright © 2021 Fortinet, Inc. All rights reserved. Fortinet®, FortiGate®, FortiCare®and
FortiGuard®, and certain other marks are registered trademarks of Fortinet, Inc., and
other Fortinet names herein may also be registered and/or common law trademarks of
Fortinet. All other product or company names may be trademarks of their respective
owners. Performance and other metrics contained herein were attained in internal
lab tests under ideal conditions, and actual performance and other results may vary.
Network variables, dierent network environments and other conditions may aect
performance results. Nothing herein represents any binding commitment by Fortinet,
and Fortinet disclaims all warranties, whether express or implied, except to the extent
Fortinet enters a binding written contract, signed by Fortinet’s General Counsel, with
a purchaser that expressly warrants that the identied product will perform according
to certain expressly-identied performance metrics and, in such event, only the
specic performance metrics expressly identied in such binding written contract
shall be binding on Fortinet. For absolute clarity, any such warranty will be limited to
performance in the same ideal conditions as in Fortinet’s internal lab tests. Fortinet
disclaims in full any covenants, representations, and guarantees pursuant hereto,
whether express or implied. Fortinet reserves the right to change, modify, transfer, or
otherwise revise this publication without notice, and the most current version of the
publication shall be applicable.
Technical Documentation https://docs.fortinet.com
Knowledge Base https://kb.fortinet.com
Forums https://forum.fortinet.com
Customer Service & Support https://support.fortinet.com
Training Services https://training.fortinet.com
FortiGuard Threat Research & Response https://www.fortiguard.com
Package Contents 4
Hardware Installation 5
Camera Connection 10
Technical Specications 11
Register for Support 13
Cautions and Warnings 14
Regulatory Notices 15
Table of Contents
Page 4
Package Contents
• 1x FortiCam camera
• 4x mounting screws and 4x anchors
• 1x waterproof connector assembly
• 1x spare dry pack
• 1x alignment sticker
Page 5
Hardware Installation
• Before installing surveillance cameras, design your system carefully
and test the location and coverage of each camera by temporarily
connecting the camera to the FortiRecorder NVR. Additionally, decide
whether to run the cables through the wall/ceiling (drilling required) or
along the wall/ceiling through the cable notch on the base.
• Install the camera in a protected location that is not easily accessible,
and is away from impacts or heavy vibrations.
• Avoid exposure to direct sunlight in outdoor installation for better
image quality and longer service life.
• Provide adequate grounding to the unit and the PoE injector, in
compliance with your local electrical code or regulations. The
grounding wire color must be a green-and-yellow combination and
the conductor size must be a minimumm of 18 AWG.
• Hire qualed technicians to carry out maintenance and repairs.
Disconnect power from the unit when performing maintenance tasks.
• The included mounting screws are 4mm in diameter and 25mm in
length.
Page 6
To install the camera
1. Remove the dome cover by loosening the T10 anti-tamper screws.
Use caution with the electronic parts.
2. Open the MicroSD card socket lid by sliding it backwards. This step
and step 3 are only required if onboard storage is preferred.
Page 7
3. Insert a MicroSD card into the socket, close the lid, and then slide the lid
until you hear a click.
4. Place the alignment sticker on the wall or ceiling to drill mounting
holes. Drill a cable routing hole larger than 25mm if desired.
Page 8
5. Assemble the waterproof connector onto the Ethernet cable.
6. Attach the camera to the wall or ceiling.
Page 9
7. Adjust the 3-axis mechanism horizontally, vertically, and circularly to
your desired angle.
8. Replace the desiccant from the inside of the dome cover.
9. Install the dome cover.
Page 10
Camera Connection
Caution: This device complies with IEEE 802.3af PoE specication. Do
not use any PoE injectors that are not IEEE 802.3af compliant as they may
damage your device.
To connect the camera
1. Connect the Ethernet port of the camera to the FortiRecorder NVR
via a PoE switch. The camera gets its IP address from the DHCP
server automatically.
2. Go to the FortiRecorder web UI to congure the discovered
camera. For details, see the FortiRecorder Administration Guide on
http://docs.fortinet.com.
To reset the camera to factory default
1. Remove the top cover with an allen key to expose the Reset button (see
the picture on page 6).
2. Press and hold the Reset button for 10 seconds and then release the
button.
Note: The default IP address of the camera is 192.168.1.245.
Inhaltsverzeichnis
Andere Fortinet Sicherheitskamera Handbücher
Fortinet
Fortinet FortiCam MD40 Installationsanleitung
Fortinet
Fortinet FortiCam SD20 Installationsanleitung
Fortinet
Fortinet FortiCam FD40 Bedienungsanleitung
Fortinet
Fortinet FortiCam FE120B Installationsanleitung
Fortinet
Fortinet FortiGate Rugged 60D Bedienungsanleitung
Fortinet
Fortinet FortiCam FD55-CA Bedienungsanleitung
Fortinet
Fortinet FortiCam 20A Bedienungsanleitung
Fortinet
Fortinet FortiMail-400C Bedienungsanleitung
Fortinet
Fortinet FortiCam SD20B Installationsanleitung
Fortinet
Fortinet FortiCam MC51 Bedienungsanleitung
Fortinet
Fortinet FortiCam MC51-C Bedienungsanleitung
Fortinet
Fortinet FortiCam CD51 Installationsanleitung
Fortinet
Fortinet FortiCam FE120 Installationsanleitung
Fortinet
Fortinet FortiCam FE120B Bedienungsanleitung
Fortinet
Fortinet FortiCam PD50 Bedienungsanleitung
Fortinet
Fortinet FortiCam OB30 Bedienungsanleitung
