Franke ARTH101 Bedienungsanleitung

18-05.633b-Exp.fm/13.11.29

Installation and operating instructions Montaż i instrukcja obsługi

EA-Nr.: 76 12982 001451

FAR-Best.-Nr.: 8003 99 99

ARTH101

Franke Aquarotter GmbH, Germany

Inhaltsverzeichnis11.fm

...............................................................3

Please refer to the graphics in the German Instal-

lation and Operating Instructions.

...............................................................11

Prosimy przyjąć grafikę z niemieckiej instrukcji

montażu i obsługi.

18-05.633b-GB.fm

0English

76 12982 001451 ....... Type 5001 for PROGRESS

Please refer to the graphics in the German Installation and Operating Instructions.

0Table of Contents

1. Abbreviations and Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2. Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

4. Important Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Description of Product

5. Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

6. Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

7. Scope of Delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

8. Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation, Function and Commissioning

9. Installing the Height Adjuster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

10. Mounting the Hair Dryers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

11. Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Maintenance

12. Maintenance and Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

13. Replacing the Coiled-strip Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

14. Fault Correction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

15. Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

18-05.633b-GB.fm

1. Abbreviations and Units

2. Key

Warning!

Failure to observe can result in injury or even death.

Caution!

Failure to observe can result in material damage.

☞Important!

Failure to observe can cause the product to malfunction.

☞Useful information for optimally handling the product.

3. Warranty

Liability is accepted according to the General Terms and Conditions of Business and

Supply.

Use original replacement parts only!

4. Important Notes

• Children and persons with limited capabilities or inadequate knowledge are

permitted to use the equipment only under adult supervision.

• Installation, commissioning and maintenance are to be performed only by a qualified

electrical technician according to the instructions provided and in accordance with

legal requirements and acknowledged rules of technology.

• All technical connection regulations specified by the local electric utility companies

must be complied with.

RCD Residual Current Protective Device,

Leakage current-protective circuit breaker

EA No. European Article Number

FAR Order No. Franke-AQUAROTTER Order No.

Conversion 1 mm = 0.03937 inches

1inch=25.4mm

All length specifications in the graphics are in mm.

18-05.633b-GB.fm

5. Application

Height adjuster for hair dryer for application in semi-public as well as public commercial

facilities.

Continuously variable with constant-tension coiled-strip spring, guide rail made of

anodized special aluminium, with 4 mm full-surface glued crystal mirror and concealed

vandal-proof cable routing.

6. Technical Specifications

7. Scope of Delivery

8. Dimensions

9. Installing the Height Adjuster

Warning!

• The height adjuster for hair dryers must be fastened outside of the range of persons

using a bath or shower.

• Connect the height adjuster to the protective earth conductor system.

• The electrical connection is to be customer-provided with a suitable earth leakage

circuit breaker (RCD) for a maximum nominal fault current of 30 mA.

• The cross section of the electric line must be dimensioned by an electrical specialist

on site.

Failure to observe can mean risk of death or material damage, e.g. from electric shock or

fire.

Operating voltage: 230 V ~ / 50 Hz

Protection class: I

Height adjustment

capability:

600 mm continuous

Quantity Description

1Heightadjuster

1 Attachment set

1 Installation and Operating Instructions

18-05.633b-GB.fm

☞Important!

• Install the height adjuster vertically on a flat wall surface. Use spacers to compensate

for any uneven wall surfaces (see Accessories, Chapter 15).

• Protect the height adjuster against drill dust.

Failure to observe can cause the height adjuster to work improperly, for example the

guide block may jam.

☞The recommended distance from the floor to the lower edge of the height adjuster is

1,200 mm.

☞For on-wall installations, the wall mounts have cable openings in the frontal side.

☞The recommended distance from the floor to the exit-point of the connecting lines in the

upperwallmount(a)is2,350mm.

9.1

Mark the holes (b) for the wall mounts (a, e).

9.2

Drill according to the markings. Insert the dowels.

9.3

Use a 3-core-electric cable to provide a permanent electric connection.

9.4

Connect the connecting line to the terminal in the upper wall mount (a).

Option:

Guide the connecting line out from the lower wall mount.

☞If the existing building situation requires, the electric line can also be guided out from

the wall in the lower wall mount (e).

☞The recommended distance from the floor to the exit-point of the connecting lines in the

lowerwallmount(e)is1,250mm.

9.5

Install a connecting line from the terminal in the upper wall mount (a) through the

duct (d) to the lower wall mount (e).

9.6

Use a terminal (not included) to connect the connecting line to the electric line in the

lower wall mount (e).

9.7

Use the screws and washers to fasten the height adjuster to the fastening points (b) on

the wall mount.

Caution!

To avoid scratches, use a rubber hammer when driving the covers into the fastening

points.

9.8

Drive the covers into the fastening points so that they are flush with the surface.

18-05.633b-GB.fm

10. Mounting the Hair Dryers

☞Important!

Carefully observe the installation and operating instructions of the respective hair dryer

manufacturer.

10.1

Connect the protective earth conductor of the guide block to the protective earth

conductor terminal in the hair dryer.

10.2

Use the cap nuts to fasten the hair dryer to the stay bolts (c, see illustration Chapter 9)

on the mounting plate of the guide block.

10.3

For further details please consult the Installation and Operating Instructions for the hair

dryer.

11. Function

Push or pull the handle of the guide block to move the hair dryer into the required

position.

12. Maintenance and Servicing

• Include the device in the list of electrical equipment that requires periodic checking.

• Clean the device regularly taking into account the frequency of use and the amount of

soiling that takes place in the respective location.

• If the system does not operate smoothly or there are irregular running noises, clean

and grease the coiled-strip spring or replace it.

18-05.633b-GB.fm

13. Replacing the Coiled-strip Spring

Warning!

• Before opening the device, completely disconnect it from the mains supply.

Failure to observe can result in injury or even death due to electric shock.

• Wear safety gloves.

Failure to observe could result in injuries from the sharp edges of the coiled-strip spring.

Remove the height adjuster

13.1

Demount the hair dryer and the mounting plate (y) of the guide block.

Caution!

In order to prevent damaging the wall mount while prying out the covers from the

fastening points, drill auxiliary holes into the covers (x).

13.2

Use an extruder to pry into the auxiliary holes in the covers (x) and then lift the covers

out of the fastening points of the wall mount.

13.3

Remove the screws and washers from the wall mounts and then detach the height

adjuster from the wall.

13.4

Disconnect the connecting line of the height adjuster.

Caution!

Place the height adjuster on a soft cloth to prevent scratches.

Remove the old coiled-strip spring

13.5

In the upper wall mount (a) remove the earthingscrew(c)andthe4otherscrews(b)

from the guide rails and the terminal fastener.

13.6

Pull off the upper wall mount (a).

13.7

Carefully allow the guide block to slide upwards in order to unstrain the coiled-strip

spring (g).

13.8

Unscrew the spacers (d).

13.9

Remove the fastening screws (e) of the coiled-strip spring from the guide rail.

13.10

Pull the guide block upwards and out together with the spiral cable and the cable-guide

rod.

13.11

Unscrew the lock nut (f) on the screw axle.

13.12

Unscrew the screw axle (h) out of the coiled-strip spring.

13.13

Remove the coiled-strip spring.

18-05.633b-GB.fm

Install a new coiled-strip spring

☞Important!

• Grease the bearing bore of the coiled-strip spring and the skids of the slider (i). Use

grease only; do not use oil!

• Carefully note the position in which the coiled-strip spring is mounted. The coiled-

strip spring must roll off along the right-hand side of the guide rail.

• Make sure that the coiled-strip spring moves easily and that the locking nut (f) is

firmly seated.

13.14

Reassemble in the reverse order.

13.15

Pull the guide block all the way down and grease the surfaces of the new coiled-strip

spring.

Mount the height adjuster

☞Important!

• Before mounting, make sure that the height adjuster moves easily and that the screw

connections are properly tightened.

13.16

Mount the height adjuster (see Chapter 9.).

13.17

Mount the mounting plate and the hair dryer (see Chapter 10.).

14. Fault Correction

If you are unable to correct a fault or if the fault is not described in the fault correction section,

please inform our customer service department!

Fault Cause Remedy

Height adjuster

moves stiffly

– The screw axle of the coiled-strip spring

has been screwed in too far

➯Adjust it

– The slider and the guide rails are dirty ➯Clean and grease

– The coiled-strip spring is dirty ➯Clean and grease,

replace if necessary

Running noise – The slider and the guide rails are dirty ➯Clean and grease

– The coiled-strip spring is dirty ➯Clean and grease,

replace if necessary

– The coiled-strip spring is defective ➯Replace it

Irregular motion – The slider and the guide rails are dirty ➯Clean and grease

– The coiled-strip spring is dirty ➯Clean and grease,

replace if necessary

– The coiled-strip spring is defective ➯Replace it

Guide block sinks – The coiled-strip spring is fatigued ➯Replace it

– The coiled-strip spring is defective ➯Replace it

18-05.633b-GB.fm

15. Replacement Parts

Designation Order No.

1Wallmount

White . . . . . . . . . . . . . . . . . . . . . . 84-51-5026-00.09-X

Pearl-Enzian. . . . . . . . . . . . . . . . . 84-51-5026-00.05-X

2 Covers for wall mount

White . . . . . . . . . . . . . . . . . . . . . . 84-53-5013-00.09-X

Silver . . . . . . . . . . . . . . . . . . . . . . 84-53-5013-00.07-X

3 Spiral cable . . . . . . . . . . . . . . . . . . . . 84-42-5011-22.09-X

4 Coiled-strip spring. . . . . . . . . . . . . . . 84-69-5012-00.50-X

Accessories Order No.

Spacer plates for wall mount, white

2 mm . . . . . . . . . . . . . . . . . . . . . . 84-52-5015-00.09-02

4 mm . . . . . . . . . . . . . . . . . . . . . . 84-52-5015-00.09

6 mm . . . . . . . . . . . . . . . . . . . . . . 84-52-5015-00.09-06

PROGRESS hair dryer

Type 1206 . . . . . . . . . . . . . . . . . . 8003 94 24

Type 1200 . . . . . . . . . . . . . . . . . . 8003 95 24

Type 1213 . . . . . . . . . . . . . . . . . . 8015 17 24

Inhaltsverzeichnis

Sprachen:

Andere Franke Inneneinrichtung Handbücher

Franke

Franke SC140HP Bedienungsanleitung

Franke

Franke SIRIUS WSPL0017 Bedienungsanleitung

Franke

Franke 2000102672 Bedienungsanleitung

Franke

Franke EXOS600X Bedienungsanleitung

Franke

Franke RODX606 Bedienungsanleitung

Franke

Franke M600HD Bedienungsanleitung

Franke

Franke 7612210052316 Bedienungsanleitung

Franke

Franke CONTINA CNTX91 Bedienungsanleitung

Franke

Franke HEAVYDUTY M400HD Bedienungsanleitung

Franke

Franke STRATOS STRX601E Bedienungsanleitung

Franke

Franke SIRX754 Bedienungsanleitung

Franke

Franke RODX606E Bedienungsanleitung

Franke

Franke Stratos STRX625 Bedienungsanleitung

Franke

Franke EXOS625X Bedienungsanleitung

Franke

Franke EXOS Betriebsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung