Franke PWC3O0002 Bedienungsanleitung

Installation and operating instructions Istruzioni per il montaggio e l’uso

ZMI_001_2030048572-PWC3O0002_#SALL_#AQU_#V2.fm / 01.05.22

EA-Nr.: 7612982258794

Best.-Nr.: 2030048572

PWC3O0002

Inhaltsverzeichnis26.fm

- 2 -

...................................................................................... 3

Please refer to the graphics in the German Installation and

Operating Instructions.

...................................................................................... 13

Per le grafiche fare riferimento alle Istruzioni per il montaggio e

l’uso in tedesco.

- 3 -

ZMI_001_2030048572-PWC3O0002_#SEN_#AQU_#V2.fm

0English

Tap Components for Washbasin Unit for Contact-Free Water/Hot Air

Sequential Control.

Please refer to the graphics in the German Installation and Operating Instructions.

0Table of Contents

1. Abbreviations and units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2. Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

4. Important notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Description of product

5. Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

6. Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

7. ID settings (29260) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

8. Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

9. Installation example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Assembly, function and commissioning

10. Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

11. Assembly of hand dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

12. Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

13. Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

14. Setting the sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Maintenance

15. Maintenance and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

16. Replacing the filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

17. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

18. Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

ZMI_001_2030048572-PWC3O0002_#SEN_#AQU_#V2.fm

- 4 -

1. Abbreviations and units

2. Key

Warning!

Failure to observe can result in bodily injury or even death.

Caution!

Failure to observe can result in material damage.

☞Important!

Failure to observe can cause the product to malfunction.

☞Useful information for optimum handling of the product.

3. Warranty

Liability is accepted in accordance with the General Terms and Conditions of

Business and Supply.

Use only genuine spare parts!

4. Important notes

• Installation, commissioning and maintenance must be performed only by a

qualified expert in accordance with the instructions provided, legal requirements

and recognised engineering standards.

• All technical connection regulations specified by the local water and electricity

supply companies must be observed.

• The power supply should be switched off before any work is carried out.

• We reserve the right to make changes.

DN Nominal diameter in mm

RCD Residual current protective device,

Earth leakage circuit breaker

SELV Safety extra low voltage

EA-Nr. European article number

Best.-Nr. Aquarotter order number

Conversion 1 mm = 0.03937 inches

1 inch = 25.4 mm

All length specifications in the graphics are in mm.

- 5 -

ZMI_001_2030048572-PWC3O0002_#SEN_#AQU_#V2.fm

5. Application

A3000 open, electronically controlled washbasin tap, DN 15, with concealed trigger

via pictograph tile, for washing hands and sequential control for drying hands for

wall-mounted washbasin, with possibility of external control, such as tap adjustment

and communication using ECC function controller. For connection to premixed hot

water or cold water. The flow time can be set in one-second steps.

Control functions:

– Optional temperature sensor with temperature measurement and log saving

every 60 seconds, every 10 seconds for thermal disinfection

– Time-controlled hygiene flushes, optionally at fixed intervals or at a defined

interval after last operation

Additional functions with ECC function controller (Ethernet):

– Automatic thermal disinfection in accordance with DVGW Work Sheet W 551

and safety shutdown

– Cleaning deactivation

6. Technical specifications

Minimum flow pressure: 1.0 bar

Recommended flow pressure: 1-5 bar

Maximum operating pressure: 10 bar

Calculated flow rate: 0.20 l/s

Volumetric flow: 0.50 l/s at a flow pressure of 3 bar

Washbasin components 24 V DC

Hand dryer 230 V AC

Power consumption:

Washbasin components 7 W

Hand dryer 1770 W

Communication: Ethernet via ECC function controller

Protection class:

Electronic module IP 68

Solenoid valve IP 44

ZMI_001_2030048572-PWC3O0002_#SEN_#AQU_#V2.fm

- 6 -

7. ID settings (29260)

Water-air combi/capacitive sensor/hand dryer sequential control.

FUNCTION:

Start of water flow at touch of button, automatic stop after end of set flow time in

10 s. Then hand dryer starts. Automatic stop after end of set flow time in 20 s.

SENSORS:

S2: Channel 1/capacitive sensor

ACTUATORS:

A1.1: Channel 1/power switch/hand dryer

A1.2: Channel 1/solenoid valve

SETTINGS:

8. Dimensions

9. Installation example

Range - / - / -

TempSensor 1 action -

TempSensor 2 action -

AquaPay -

Flow Time 10 sec. / - / -

Overrun time - / - / -

Safety shutdown after -

Reflection alarm after -

Concurrence suppression -

Flow time reduction -

Cleaning deactivation 1 min.

Hygiene flush (dynamic) Interval: 24 h/flow time: 10 sec.

Hygiene flush (fixed) Interval: 0 h/flow time: 10 sec.

Power-on flush -

TD Application Time -

TD water saving function -

TD cooling -

- 7 -

ZMI_001_2030048572-PWC3O0002_#SEN_#AQU_#V2.fm

10. Assembly

Warning!

• Place the power supply (not part of the delivery, see Chapter 18., accessories)

outside the wet area in a separate room.

• Operate the product only with safety extra low voltage (SELV). The components

must not be earthed.

• Protect the power supply with a residual current circuit breaker (RCD).

Failure to observe this instruction can result in death or material damage due to

electric shock or fire, for example.

☞Lay the system line (not part of the delivery, see Chapter 18., accessories) in an

empty pipe (to be provided by the customer) from the power supply to the taps and

loop through.

Warning!

Only operate taps with the designated filter.

Failure to observe this instruction can result in damage to the tap.

10.1

Important!

Prior to the assembly process, flush the pipework in accordance with DIN 1988.

10.2

Establish the water connection.

☞Take note of the flow direction.

10.3

Use an Allen key to close the water volume regulator.

a: Closed

b: Open

10.4

Unscrew the locking screw (c) on the water volume regulator.

10.5

Replace the (d) filter.

☞Important!

Note the installation position of the filter.

10.6

Remove the flush connector.

10.7

Attach the connection cable.

10.8

Insert the solenoid valve with the seals.

☞Take note of the flow direction.

10.9

Open the water volume regulator (see Work step 10.3).

10.10

Affix the sensor (e) to the rear of the plastic tile (f).

☞No tile cement may be applied between the sensor and the plastic tile.

ZMI_001_2030048572-PWC3O0002_#SEN_#AQU_#V2.fm

- 8 -

Installing the electrical T-distributor

☞Important!

The components of the electrical T-distributor may only be installed after the power

has been switched off.

☞Recommended system cable see Chapter 18., accessories.

When using cables other than the system cable, pay attention to the different colour

code. The outer diameter must not exceed 7.5 mm.

10.11

Remove the sheathing (a) of the system cable (approx. 40 mm).

10.12

Push the cap nut (c) onto the system cable (b) up to the stop.

☞The various wire guides are marked with numbers 1 to 4.

A: Union nut

B: Best.-Nr. 2000104272

Best.-Nr. 2000104274

Best.-Nr. 2000100801

Best.-Nr. 2000100852

10.13

Push the wires (d) into the wire guides (e) in accordance with their colours.

10.14

Cut off the projecting wire ends flush, i.e. without protrusions.

10.15

Push the cap nut (c) onto the electrical T-distributor (f) and tighten with the required

torque (1.2 Nm).

Caution!

Note the polarity.

The same wire colour must be in the same wire guide for both union nuts.

☞When tightening the union nut, the electrical contact and tension relief are created

automatically.

Special seals act as protection from dust and water.

1 brown red

2white white

3 blue blue

4 black black

- 9 -

ZMI_001_2030048572-PWC3O0002_#SEN_#AQU_#V2.fm

10.16

Connect the cables between the electronics module, power switch, and sensor.

A: Power switch (actuator 1)

B: Actuator 2 (optional)

C: 0-10 V analogue output

D: Cold water temperature sensor (optional)

E: Hot-water temperature sensor (optional)

F: Capacitive sensor (sensor connection 2/3)

G: Not used (sensor connection 1)

H: Electrical T distributor system cable (power)

K: Electronic module

10.17

Connect the cables between the electronics module, solenoid valve, and hand dryer.

F: Electronics module (actuator 1)

G: Solenoid valve

H: Switch contact for hand dryer

11. Assembly of hand dryer

11.1

Attach the mounting template to the wall. The recommended mounting height is

between 130 and 140 cm above the floor.

11.2

Drill the mounting template accordingly (A, B, C, D).

11.3

Remove the mounting template from the wall. Insert the wall plugs.

11.4

Turn out the two screws (a) on the housing.

11.5

Remove the hand dryer housing.

11.6

Guide the electrical cable and the cable of the power switch through the base plate.

11.7

Mount the base plate and motor to the wall.

1Screw

2 Washer

3Spacer

4 Base plate

5 Washer

6Nut

11.8

Connect the electrical cable (a).

L: Red (or brown)

N: Black (or blue)

: Green (or yellow)

11.9

Connect the cable of the power switch (b).

11.10

Screw the housing (c) to the base plate.

11.11

Shorten the hose (d).

ZMI_001_2030048572-PWC3O0002_#SEN_#AQU_#V2.fm

- 10 -

☞Important!

Do not (d) bend the hose.

11.12

Attach the hose max. 20 mm in the hand dryer outlet.

11.13

Attach the hose to the hand dryer outlet using the screws.

11.14

Push the pipe clamp onto the hose.

11.15

Attach the hose to the washbasin nozzle with the pipe clamp.

12. Startup

12.1

Turn the power on.

12.2

Allow the system to run in for at least 15 min.

12.3

Stroke over the plastic tile with your hand.

• The water will flow.

13. Function

13.1

Stroke over the plastic tile with your hand.

• The water will flow.

• The water flow stops automatically after the set flow time (10 seconds).

The hand dryer then activates for 20 seconds.

☞An automatic flushing function after 24 hours of non-use was set in the factory.

☞You can set the flow time and automatic flush using the system software.

14. Setting the sensor

14.1

Use a screwdriver to set the range.

+ Longer range

– Shorter range

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Franke Sanitärprodukte Handbücher

Franke

Franke PF-1000 Series Bedienungsanleitung

Franke

Franke CUBE FFPD3350 Bedienungsanleitung

Franke

Franke KUBUS FF4250 Bedienungsanleitung

Franke

Franke EXOS616EX Bedienungsanleitung

Franke

Franke F3SM2001 Bedienungsanleitung

Franke

Franke F5 Series Bedienungsanleitung

Franke

Franke F5ET1010 Bedienungsanleitung

Franke

Franke F5LT1012 Bedienungsanleitung

Franke

Franke MARIS FREE Handbuch

Franke

Franke CMPX538RS Bedienungsanleitung

Franke

Franke FRESNO FSG 111 Bedienungsanleitung

Franke

Franke AQFU0235 Bedienungsanleitung

Franke

Franke F5LM1010 Bedienungsanleitung

Franke

Franke AQRE430 Bedienungsanleitung

Franke

Franke SIRIUS CA210/2N Bedienungsanleitung

Franke

Franke F5 F5ST2021 Bedienungsanleitung

Franke

Franke MINERVA/IRENA Bedienungsanleitung

Franke

Franke CAMPUS HDTX506 Bedienungsanleitung

Franke

Franke AQUALINE AQLT0085 Bedienungsanleitung

Franke

Franke FS HF SWSP Handbuch

Franke

Franke F5 F5ST2034 Bedienungsanleitung

Franke

Franke F3EV2001 Bedienungsanleitung

Franke

Franke F5ET2003 Bedienungsanleitung

Franke

Franke F5 Series Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema