Freescale Semiconductor HCS12 Bedienungsanleitung

Freescale Semiconductor SLKS12QSG

Quick Reference Guide Rev. 0, 2/2008

_______________________________________________________________________

Getting Started with the Student Learning Kit

Featuring the Freescale HCS12 Microcontroller Application

Module

Freescale Semiconductor SLKS12QSG

Quick Reference Guide Rev. 0, 2/2008

Freescale Semiconductor 2

1 Introduction

This guide provides the steps necessary to begin

development with a HCS12 family

microcontroller (MCU) using your application

module and/or in conjunction with the Freescale

project board (PBMCUSLK).

This guide is separated into three main sections.

First, the software setup section will assist in

installing the CodeWarrior™ development

tools. Second, the hardware setup section will

step through configuring the project board and

application module. Third, the development

section illustrates how to create, build, and

debug an application.

Refer to the project board user guide,

application module user guide, and

CodeWarrior documentation for more details.

For demonstration applications, source code

examples, current documentation and resources;

visit www.freescale.com\universityprograms

Contents

1 Introduction.................................................................2

2 Unpack.........................................................................3

3 Software Setup............................................................3

4 Hardware Setup...........................................................3

4.1 Configuring the Application Module for independent

operation ......................................................................4

4.2.1 Configuring the Application Module for use with

the Project Board..........................................................6

4.2.3 Installing the Application Module.......................11

4.3 Windows Operating System Hardware Detection.12

5 Running the Demonstration Application.................14

6 Custom Software Development...............................15

6.1 Creating and Building a Project in CodeWarrior

Environment...............................................................15

6.2 Debugging your Application..................................19

7 Revision History........................................................22

8 Support ......................................................................22

Freescale Semiconductor SLKS12QSG

Quick Reference Guide Rev. 0, 2/2008

Freescale Semiconductor 3

2 Unpack

Open the shipping carton and remove the contents. Locate the packaging list and verify items have been

received from the packaging list.

Inspect both the project board and the application module for damage that may have occurred during

shipping. If damage is found, contact www.freescale.com/support for assistance.

3 Software Setup

The following software installation is a one-time, required procedure per host PC that you intend to use

with the project board and/or application module. After completing the software setup on your host PC,

you can skip the software section on subsequent uses of your project board and/or application module

and begin the hardware setup or development sections.

To install and register CodeWarrior development tools for HCS12(X) Microcontrollers onto a host PC,

complete the instructions found inside the CodeWarrior Development Studio for Freescale HCS12(X)

Microcontrollers case.

Additional tools and training materials for CodeWarrior are available at www.freescale.com

NOTE

Academic Edition development tools are full-featured and not for commercial development. They may

only be licensed to students, faculty, and staff of accredited institutions.

Periodically check http://www.freescale.com/codewarrior for updates and patches to your development

tools. For questions on CodeWarrior development tools, visit http://www.freescale.com/support

4 Hardware Setup

For more information on the Application Module operation, jumper descriptions and settings please

refer to the development board User Guide or visit www.freescale.com\universityprograms for latest

information.

Freescale Semiconductor 4

4.1 Configuring the Application Module for independent operation

1) By default, the application module is configured to run independently out of the box. Verify that

all the jumper settings are configured properly on the application module as shown by Figure 1.

2) Plug in the USB cable from the host PC (running CodeWarrior) to the Application Module.

3) Your Done! Proceed to Running your Demonstration application.

Figure 1. Application Module: Independent Operation Jumper Settings

Jumper Position Jumper ID Description

VR1

VX_EN

PWR_SEL Source power input from connector on-board USB.

SW1

SW2

SW3_1

SW3_2

SW3_3

SW3_4

USER Jumpers enable access to application modules features. For

push button switch (SW1:2), 4-position DIP switch 3

(SW3_1:4), LED[1:4], and to simplify circuit connections and

emphasize software development.

Freescale Semiconductor 5

LED1

LED2

LED3

LED4

RV1

RZ1

COM_EN Jumpers enable the application modules serial communication

port.

BKG

RST

BDM_EN Jumpers enable the application modules background debug

mode (BDM) circuit.

Freescale Semiconductor 6

4.2.1 Configuring the Application Module for use with the Project Board

1) Move the PWR_SEL jumper FROM “VB” TO “VX_EN”

2) Remove all COM_EN jumpers from the Application Module as shown by Figure 2.

3) Remove all BDM_EN jumpers from the Application Module as shown by Figure 2.

Figure 2 Application Module: with Project Board Operation Jumper Settings

Jumper Position Jumper ID Description

VR1

VX_EN

PWR_SEL Source power input from connector J1

SW1

SW2

SW3_1

SW3_2

SW3_3

SW3_4

USER Jumpers enable access to application modules features. For

push button switch (SW1:2), 4-position DIP switch 3

(SW3_1:4), LED[1:4], and to simplify circuit connections and

emphasize software development.

Freescale Semiconductor 7

LED1

LED2

LED3

LED4

RV1

COM_EN

Remove jumpers to disable the application module serial

communication port.

*Note: The COM pins are shared when using the PBMCUSLK

with the application module. Conflicts may occur if both are in

use simultaneously.

BKG

RST

BDM_EN

Remove jumpers to disable the application modules

background debug mode (BDM) circuit.

*Note: The BDM pins are shared when using the PBMCUSLK

with the application module. Conflicts may occur if both are in

use simultaneously.

Freescale Semiconductor 8

4.2.2 Configure the Project Board

Place the project board on a flat and sturdy surface. Ensure sufficient space is available around the

project board to safely construct and test prototyped circuits.

Verify that all the jumper settings are configured properly on the project board as shown by Figure 3.

Highlighted blocks indicate the on or installed position of jumpers. Circles indicate the location on the

project board where the jumpers are located.

Figure 3. Project Board Jumper Settings

Freescale Semiconductor 9

The table below summarizes the required jumper settings for use with the S12 Application Modules.

Please refer to project board user guide for more details and alternative configurations.

Jumper Position Jumper ID Description

VIN

PWR_SEL Selects VIn (wall power transformer) as the default power

source for the project board.

USB

PWR_SEL

+5V_SEL Selects USB (power via USB cable from host PC) as the default

power source for the project board. This jumper overrides

PWR_SEL in USB position.

+5V

+3.3V

VDD_SEL Sets VDD to +5V for project board.

15V_EN

15V_EN Enables PS1 output (±15 V supply from dc-dc converter) to the

project board. Selects if BDM Multilink pod on the project board

has a generic or unique ID associated with the host PC.

J301

J301 Selects if BDM Multilink pod on the project board has a

generic or unique ID associated with the host PC.

VDD

GND

MOD_PWR

Provides PWR & GND to Application Module

GPIO

SS_SEL Selects dedicated SS input source to MCU_23 (SS) on MCU

PORT connector to transfer data to LCD panel.

MOSI

MISO

LCD_EN Connects dedicated SPI signals to LCD port.

Freescale Semiconductor 10

SCK

ADJ

FIX

CONTRAST Selects fixed LCD contrast voltage

MONO8

COM

COM_SEL Selects RS-232 communications for project board COM port.

CTS

RTS

RXD

TXD

COM_EN Enables all RS-232 communication signals individually for

project board COM port.

AMPL

AMPL Oscillator output at reduced amplitude – 3.3 Vpp

LED_EN

LED_EN Enables all LED outputs on project board.

UFEA Enables access to direct connect features for buzzer, four push

buttons, four LEDs, and potentiometer to MCU PORT

connector to simplify circuit connections and emphasize

software development.

Andere Handbücher für HCS12

Inhaltsverzeichnis

Andere Freescale Semiconductor Mikrocontroller Handbücher

Freescale Semiconductor

Freescale Semiconductor FRDM-KL02Z Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor QE128 Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor M68HC08 series Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor M68HC08RG Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor MPC5565 Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor *KE02 Series Gebrauchsanweisung

Freescale Semiconductor

Freescale Semiconductor MPC5553 Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor TWR-K21F120M Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor MC9S12XHY Series Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor NXP DEMO9S08SF4 Technisches Datenblatt

Freescale Semiconductor

Freescale Semiconductor i.MX53 SABRE Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor MPC5604B Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor MC9S12XE Series Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor Flexis Series Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor MPC5607B Montage- und Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor MC9S12ZVHL64 Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor KL02 Series Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor Logic Zoom ColdFire LITE Series Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor MMA7455L Gebrauchsanweisung

Freescale Semiconductor

Freescale Semiconductor Kinetis TWR-K21D50M Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor 56F8000E Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor *KE02 Series Gebrauchsanweisung

Freescale Semiconductor

Freescale Semiconductor MMA7260QT Gebrauchsanweisung

Freescale Semiconductor

Freescale Semiconductor MCF51CN128 Bedienungsanleitung

Beliebte Mikrocontroller Handbücher anderer Marken

AMS

AMS AS7261 Demo Kit Bedienungsanleitung

Novatek

Novatek NT6861 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266 SDK Einrichtungshandbuch

Nuvoton

Nuvoton ISD61S00 ChipCorder Leitfaden

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Bedienungsanleitung

Texas Instruments

Texas Instruments Chipcon CC2420DK Bedienungsanleitung

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Bedienungsanleitung

NEC

NEC 78GK0S/K 1+ Series Montage- und Bedienungsanleitung

Mikroe

Mikroe SEMITECH N-PLC Click Montage- und Bedienungsanleitung

Intel

Intel Agilex Bedienungsanleitung

Cypress

Cypress CY4607 HX2VL Bedienungsanleitung

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Bedienungsanleitung

Texas Instruments

Texas Instruments TMS320F2837 D Series Bedienungsanleitung

CYPRES

CYPRES CY14NVSRAMKIT-001 Bedienungsanleitung

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266EX Betriebsanleitung

Abov

Abov AC33M8128L Bedienungsanleitung

Laird

Laird BL654PA Bedienungsanleitung