Freescale Semiconductor LS1043ARDB Bedienungsanleitung

1 Introduction

This document describes the LS1043A reference design board

(LS1043ARDB) and hardware kit containing the board. It also

explains the basic board operations in a step-by-step manner.

This document describes the settings required to connect

switches, connectors, jumpers, push buttons, and LEDs to the

peripheral devices.

The LS1043ARDB functions with an integrated development

environment (IDE), such as Freescale CodeWarrior. The

instructions for working with the IDE are beyond the scope of

this document.

The list of items included in the LS1043ARDB hardware kit is

provided with the LS1043ARDB board support package

(BSP). Optional hardware components that are not included in

the LS1043ARDB hardware kit are:

• TDM modules

• PCIe/mini-PCIe cards

• CodeWarrior TAP (CWTAP)

2 Related documentation

The table below lists and explains the additional documents

that you can refer to, for more information about

LS1043ARDB.

Freescale Semiconductor Document Number: LS1043ARDBQS

Quick Start Rev. 1, 11/2015

QorIQ LS1043A Reference Design

Board Quick Start

Contents

1 Introduction.............................. .............................. 1

2 Related documentation............................................1

3 LS1043ARDB system board interface....................2

4 Getting started with LS1043ARDB.... ....................3

5 Switch configurations................... ..........................4

6 Jumper settings......................... .............................. 8

7 Interfaces.................................................................9

8 Connectors.............................................................16

9 Push and slide buttons........................................... 18

10 LED indicators........................... ...........................19

11 Setting up CodeWarrior TAP............. .................. 21

12 LS1043ARDB operating

configurations................................... .................... 22

13 NOR flash memory map........................................24

14 Revision history.................................................... 24

Some of the documents listed below may be available only under a non-disclosure agreement (NDA). To request access to

these documents, contact your local field applications engineer or sales representative.

Table 1. Related documentation

Document Description

QorIQ LS1043A Reference Manual

(LS1043ARM)

Provides a detailed description on the LS1043A multicore processor and its

features, such as memory map, serial interfaces, power supply, chip features,

and clock information

QorIQ LS1043A Data Sheet Contains information on LS1043A pin assignments, electrical characteristics,

hardware design considerations, package information, and ordering information

3 LS1043ARDB system board interface

The figure below shows the front view of the LS1043ARDB.

Figure 1. LS1043ARDB front view

The figure below shows the rear view of the LS1043ARDB.

Figure 2. LS1043ARDB rear view

LS1043ARDB system board interface

QorIQ LS1043A Reference Design Board Quick Start, Rev. 1, 11/2015

2 Freescale Semiconductor, Inc.

4 Getting started with LS1043ARDB

This section describes how to set up and use the LS1043ARDB.

4.1 Prepare board

To ensure correct board setup, prepare the board using the steps below:

1. Verify that the LS1043ARDB hardware kit contains all items mentioned in the kit contents list provided with the

LS1043ARDB packing list.

2. Verify the LS1043ARDB dual inline package (DIP) switch settings. See Switch configurations for details.

3. Verify the LS1043ARDB jumper settings. See Jumper settings for details.

4. Attach the required devices to the LS1043ARDB connectors. See Connectors for details.

5. Optionally, connect the CodeWarrior TAP to the LS1043ARDB. See Setting up CodeWarrior TAP for details.

6. Install the DC power cord from the desktop power supply to the board power inlet.

4.2 Power up and use board

After the system has been properly set up, follow the steps below to power up and use the LS1043ARDB:

1. Turn ON the power switch (SW2).

2. The power LED (D1) on the printed circuit board (PCB) and the left LED (D13) of the chassis become green when the

board is powered up. D3 LED on the PCB remains OFF while the boot code is fetched.

3. Connect the universal serial bus (USB) cable to the mini-USB port in the front panel used for console. You need to

install the USB drivers on the host machine before using the serial terminal. You can download the latest drivers from

https://developer.mbed.org/handbook/Windows-serial-configuration.

4. If you are using the RJ45 port, connect the RJ45 to UART cable to the J4 bottom port and set SW3[3] to OFF.

You will see messages, similar to the ones shown below, on the console window (or in the CodeWarrior IDE, if using

that):

U-Boot 2015.01-00055-g7aba6ad (Nov 19 2015 - 14:46:03)

Clock Configuration:

CPU0(A53):1600 MHz CPU1(A53):1600 MHz CPU2(A53):1600 MHz

CPU3(A53):1600 MHz

Bus: 400 MHz DDR: 1600 MT/s FMAN: 500 MHz

Reset Configuration Word (RCW):

00000000: 08100010 0a000000 00000000 00000000

00000010: 14550002 80004012 e0025000 c1002000

00000020: 00000000 00000000 00000000 00038800

00000030: 00000000 00001101 00000096 00000001

Board: LS1043ARDB, boot from vBank 0

CPLD: V1.4

PCBA: V2.0

SERDES Reference Clocks:

SD1_CLK1 = 156.25MHZ, SD1_CLK2 = 100.00 MHz

I2C: ready

DRAM: 2 GiB (DDR4, 32-bit, CL=12, ECC off)

Waking secondary cores to start from fff2a000

All (4) cores are up.

Getting started with LS1043ARDB

QorIQ LS1043A Reference Design Board Quick Start, Rev. 1, 11/2015

Freescale Semiconductor, Inc. 3

Using SERDES1 Protocol: 5205 (0x1455)

fman_port_enet_if:71: port(FM1_DTSEC3) is OK

fman_port_enet_if:77: port(FM1_DTSEC4) is OK

Flash: 128 MiB

NAND: 512 MiB

MMC: FSL_SDHC: 0

EEPROM: NXID v1

PCIe1: disabled

PCIe2: Root Complex no link, regs @ 0x3500000

PCIe3: Root Complex no link, regs @ 0x3600000

In: serial

Out: serial

Err: serial

Net: Fman1: Uploading microcode version 108.4.15

FM1@DTSEC1, FM1@DTSEC2, FM1@DTSEC3, FM1@DTSEC4, FM1@DTSEC5, FM1@DTSEC6, FM1@TGEC1

Hit any key to stop autoboot: 0

NOTE

U-Boot is updated frequently; therefore, the details given above may change slightly over

a period of time.

4.3 Restart board

To restart or reset the system, use the reset button next to the UART port (RJ45 without LED).

5 Switch configurations

In the LS1043ARDB, the configuration switches are arranged along the edge of the board. Use the following figure as a

reference.

SW5 SW4 SW3

Figure 3. DIP switch locations

With the board positioned as shown above, switches read "SW5 SW4 SW3" moving from left to right. For these types of DIP

switches:

•When a switch is up (OFF), the value is 0

• When a switch is down (ON), the value is 1

Switch configurations

QorIQ LS1043A Reference Design Board Quick Start, Rev. 1, 11/2015

4 Freescale Semiconductor, Inc.

5.1 SW3 configuration

The figure below shows the SW3 switch on the LS1043ARDB.

CLKGEN_FS0

1 2 3 4 5 6 7 8

CLKGEN_FS1

UART_SEL

SD1REFCLK_SEL

EVDD_SEL

OPENSDA_EN

TDMCLK_SD/USB

SDHC_SPICS_SEL

ON '1'

Figure 4. SW3 switch

The table below describes the SW3 configuration.

Table 2. SW3 configuration

Switch Name Description ON (1) / OFF (0) setting

SW3[1] CLKGEN_FS0 SYSCLK frequency select

•00: 66.66 MHz

• 01: 80 MHz

• 10: 100 MHz (default value)

• 11: 83 MHz

SW3[2] CLKGEN_FS1 0

SW3[3] UART_SEL UART1 output select

•0: RJ45, J4 lower one

• 1: CMSISDAP, mini-USB port (default

value)

SW3[4] SD1REFCLK_SEL SD1 REFCLK select

•0: 100 MHz (default value for the

LS1021A interposer)

• 1: 156.25 MHz (default value for the

LS1043A processor)

SW3[5] EVDD_SEL EVDD voltage select

• 0: 3.3 V (default value)

• 1: 1.8 V

Table continues on the next page...

Switch configurations

QorIQ LS1043A Reference Design Board Quick Start, Rev. 1, 11/2015

Freescale Semiconductor, Inc. 5

Table 2. SW3 configuration (continued)

Switch Name Description ON (1) / OFF (0) setting

SW3[6] OPENSDA_EN CMSISDAP JTAG forced disable

• 0: JTAG can be used by header or

CMSISDAP (default value)

• 1: CMSISDAP JTAG is forced to be

disabled

SW3[7] TDMCLK_SDHC/USB TDM CLK or SDHC/USB select

• 0: TDM CLK

• 1: SDHC/USB (default value)

SW3[8] SDHC_SPICS SDHC_DAT[4:7] or SPI_CS select

• 0: SDHC

• 1: SPI_CS (default value)

5.2 SW4 configuration

The figure below shows the SW4 switch on the LS1043ARDB.

RCW_SRC0

1 2 3 4 5 6 7 8

RCW_SRC1

RCW_SRC6

RCW_SRC7

RCW_SRC2

RCW_SRC3

RCW_SRC4

RCW_SRC5

ON '1'

Figure 5. SW4 switch

The table below describes the SW4 configuration.

Switch configurations

QorIQ LS1043A Reference Design Board Quick Start, Rev. 1, 11/2015

6 Freescale Semiconductor, Inc.

Table 3. SW4 configuration

Switch Name Description ON (1) / OFF (0) setting

SW4[1] RCW_SRC0 RCW_SRC[0:8] select

• 0_0010_0101: 16-bit NOR (default

value)

• 0_0100_0000: SDHC/eMMC

• 0_1001_1011: Hardcoded RCW

• 1_0000_0110: 8-bit NAND flash, 2 KB

page, 64 pages/block

NOTE: The RCW_SRC field (9 bits) is spread

over SW4 and SW5.

SW4[2] RCW_SRC1 0

SW4[3] RCW_SRC2 0

SW4[4] RCW_SRC3 1

SW4[5] RCW_SRC4 0

SW4[6] RCW_SRC5 0

SW4[7] RCW_SRC6 1

SW4[8] RCW_SRC7 0

SW5[1] RCW_SRC8 1

5.3 SW5 configuration

The figure below shows the SW5 switch on the LS1043ARDB.

1 2 3 4 5 6 7 8

CFG_TEST_SEL_B

BANK_SEL0

BANK_SEL1

BANK_SEL2

RCW_SRC8

SYSCLK_SEL

SW_SVR1

SW_SVR0

ON '1'

Figure 6. SW5 switch

The table below describes the SW5 configuration.

Switch configurations

QorIQ LS1043A Reference Design Board Quick Start, Rev. 1, 11/2015

Freescale Semiconductor, Inc. 7

Table 4. SW5 configuration

Switch Name Description ON (1) / OFF (0) setting

SW5[2] SYSCLK_SEL Differential SYSCLK select

• 0: Differential SYSCLK (default value)

• 1: Single-end system clock

SW5[3] CFG_TEST_SEL_B CFG_TEST_SEL for the LS1043A processor

• 0: Disables cores 3 and 4

• 1: Enables all cores (default value)

SW5[4] BANK_SEL0 Virtual bank select

• 000: No change (default value)

• 001: Virtual bank #1

• … …

• 111: Virtual bank #7

SW5[5] BANK_SEL1 0

SW5[6] BANK_SEL2 0

SW5[7] SW_SVR1 SVR[1:0]

• 00: Reserved (default value for

LS1043A)

SW5[8] SW_SVR0 0

6 Jumper settings

The table below lists the factory default jumper settings for the LS1043ARDB.

Table 5. LS1043ARDB jumper settings

Jumper Size Name/function Description

J5 1x2 pin Remote reset • Open: No activity (default value)

• Shorted: Reset the board

J6 1x2 pin Power switch • Open: Power switch is functional

(default value)

• Shorted: Power switch is disabled

J911x3 pin SPICS and SDHC Dat[4:7] voltage

selection

• 1-2 shorted: 1.8 V (default value)

• 2-3 shorted: 3.3 V

J10 1x2 pin FA_VL pin voltage setting • Open: GND

• Shorted: 1.0 V (default value)

J12 1x2 pin PWR_PROG_MTR voltage setting • Open: GND (default value)

• Shorted: 1.8 V

J13 1x2 pin PWR_PROG_SFP voltage setting • Open: GND (default value)

• Shorted: 1.8 V

J14 1x2 pin TA_BB_VDD voltage setting • Open: GND

• Shorted: 1.0 V (default value)

J1511x3 pin SPI bus voltage setting • 1-2 shorted: 1.8 V (default value)

• 2-3 shorted: 3.3 V

J22 1x3 pin External power for power amplifier

(PA) voltage for some Wi-Fi cards

• 1-2 shorted: 3.3 V (default value)

• 2-3 shorted: 5.0 V

1. J9 and J15 only exist on the SCH-28529 Rev. A1 board.

The figure below shows the jumper locations.

Jumper settings

QorIQ LS1043A Reference Design Board Quick Start, Rev. 1, 11/2015

8 Freescale Semiconductor, Inc.

J10

J15

J12

J13

J14

J22

Figure 7. LS1043ARDB jumper locations

7 Interfaces

This section describes the interfaces for the LS1043ARDB.

7.1 UART interfaces

The LS1043ARDB supports two UART interfaces, UART1 and UART2. You can use UART1 as a console port. On the

LS1043ARDB, you can use UART1 in two ways:

Interfaces

QorIQ LS1043A Reference Design Board Quick Start, Rev. 1, 11/2015

Freescale Semiconductor, Inc. 9

• Route UART1 to the RJ45 connector

• Route UART1 to the CMSISDAP circuit, which can be used on the mini-USB port

SW3[3] is used to select UART1. The figure below shows UART1 connection using the RJ45 connector when SW3[3] is

OFF.

UART1 port

Figure 8. UART1 connection using RJ45 connector

The figure below shows UART1 connection using mini-USB when SW3[3] is ON.

Interfaces

QorIQ LS1043A Reference Design Board Quick Start, Rev. 1, 11/2015

10 Freescale Semiconductor, Inc.

Inhaltsverzeichnis

Andere Freescale Semiconductor Hauptplatine Handbücher

Freescale Semiconductor

Freescale Semiconductor MPC8572E Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor DEMO908QB8 Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor Freedom FRDM-KW24D512 Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor KIT33814AEEVBE Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor TWR-K40D100M Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor T2080RDB-PC Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor FRDM-KL25Z Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor NXP 56F8013 Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor i.MX 6SoloLite Linux Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor QorIQ T1023 Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor M5211DEMO Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor MPC5668EVB Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor TWR-MPC5125 Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor S12XF Starter Kit Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor MSC8156 Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor KIT34825EPEVME Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor TWR-K60N512-KEIL Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor T4240 Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor DSPD56362EVM Kurzanleitung

Freescale Semiconductor

Freescale Semiconductor CSM-56F801 Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor i.MX 6SoloLite Linux Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor M52259DEMOKIT Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor Qorivva MPC5746R-176DS Bedienungsanleitung

Freescale Semiconductor

Freescale Semiconductor K20D72M Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung