Frequency Central Bartos Flur Rev(2) Handbuch

Frequency central

Build documentation for:

Bartos flur rev(2)

Main PCB: Panel PCB:

Bill of Materials

1K x 21

56K x 1

91K x 1

100K x 6

200K x 1

270K x 2

470K x 1

100nF poly box x 1

10uF electrolytic x 2

100uF electrolytic x 2

Bartos Flur PIC x 1

TL084 x 1

1n4148 x 1

78L05 x 1

78L09 x 1

3mm red LED x 8

B100K x 2

All pots are 9mm

Alpha

DPDT Toggle on/on x 1

Power header

Male header strip

Female header strip

Kobiconn sockets x 11

Main PCB

Populate the Main PCB as shown on the silkscreen, starting with the lowest profile

components, so:

Resistors

IC sockets

Non-electrolytic capacitors, voltage regulators

Power header and expansion header

Electrolytic capacitors - there’s an error on the silkscreen, the electrolytic polarities

are obscured, see photo:

Finally, cut 2 male header strips to the correct lengths (16, 16) and solder to the PCB so that

the long legs stick out of the rear of the PCB.

Panel PCB

Populate the Panel PCB as shown on the silkscreen in this order:

Resistors

Potentiometers (bend back the mounting lugs, then solder the middle lug in place.

Reflow and adjust as necessary so that they lie correctly. Solder lugs 1, 3 and the

mounting lugs)

Switch. You may want to use the panel to check that the switch is absolutely flush.

Now, place the 11 sockets onto the PCB with their ground lugs pointing towards where the

LEDs will eventually go. Don’t solder them in place yet! Assemble the panel to the panel

PCB, put on the pots washers and tighten up the nuts. Now set the sockets to the panel

using the nuts, making sure they all sit right. Place the assembly face down and solder the

sockets in place. This process should allow a small space to be created between the rear of

the sockets’ bodies and the PCB, allowing jacks to go in balls-deep (!). Everything should line

up nicely now!

Take the whole thing apart, ie remove the nuts/washers and take the panel away from the

panel PCB. Now solder solid core (cut off resistor legs) between the sockets’ ground tabs

and the adjacent ground pads on the PCB (shown as red dots on the image above). There is

one ground pad per sockets.

Cut 2 female header strips to the correct lengths (16, 16) and solder to the PCB so that the

black parts stick out of the rear of the PCB.

Push the 8 LEDs through their holes, remembering that the long legs go through the holes

marked ‘+’. Don’t solder them in place yet! Mount the panel PCB onto the panel, tighten up

all the nuts –it’s worth checking that the LEDs will fit smoothly through the holes before

doing this, as some can be a little tight –if needed a scalpel can be used to shave the holes

slightly wider. Place the assembly face down, push the LEDs into position and solder in

place.

Plug the Main PCB into the Panel PCB…you’re done!

http://www.frequencycentral.co.uk/ RDH 17/03/15

Andere Frequency Central Steuereinheit Handbücher

Frequency Central

Frequency Central MU System X Lowpass Filter Handbuch

Frequency Central

Frequency Central MU System X Dual ADSR Handbuch

Frequency Central

Frequency Central Raging Bull 2.0 Handbuch

Frequency Central

Frequency Central System X Amplifier Handbuch

Frequency Central

Frequency Central Stasis Leak Bedienungsanleitung

Frequency Central

Frequency Central Cosmic Background Handbuch

Frequency Central

Frequency Central Pocket Calculator Rev(2) Handbuch

Frequency Central

Frequency Central Continuum Phaser ii Handbuch

Frequency Central

Frequency Central Polygraf Handbuch

Frequency Central

Frequency Central Wave Runner Handbuch

Frequency Central

Frequency Central Continuum Phase Shifter Handbuch

Frequency Central

Frequency Central Process 26 Handbuch

Frequency Central

Frequency Central MU System X Dual Amplifier Handbuch

Frequency Central

Frequency Central More VCAs Handbuch

Frequency Central

Frequency Central Dual XVCA Handbuch

Frequency Central

Frequency Central XVCO Handbuch

Frequency Central

Frequency Central Looking glass Bedienungsanleitung

Frequency Central

Frequency Central Waverider Digital VCO Handbuch

Frequency Central

Frequency Central Deep Thought Handbuch

Frequency Central

Frequency Central Raging Bull 3.0 Handbuch

Frequency Central

Frequency Central Stasis Leak Handbuch

Frequency Central

Frequency Central Infinitely Maybe Handbuch

Frequency Central

Frequency Central CEMvelope Handbuch

Frequency Central

Frequency Central Whiteface Handbuch

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung