Friant SYSTEM 2 Bedienungsanleitung

SYSTEM 2 Installation Manual
ALL
WORKSTYLES
WELCOME

2

System 2 Installation Manual 3
SYSTEM 2 INSTALLATION MANUAL
Panels & Connectors
Denitions ��������������������������������������������������������������������������� 8
Panel to Connector: Same Height ������������������������������� 9
Panel to Connector: Change of Height �������������������� 10
Panel to Panel: Same Height������������������������������������������ 11
Panel to Panel: Change of Height ������������������������������� 12
Panel to Panel: Installation at Inline Change of
Height ����������������������������������������������������������������������������������� 13
Finished End ���������������������������������������������������������������������� 14
Finished End: Change of Height ��������������������������������� 15
Top Cap ��������������������������������������������������������������������������������� 16
Leveling Panels ������������������������������������������������������������������ 17
Door Handle Instruction ������������������������������������������������� 18
Wall Starts �������������������������������������������������������������������������� 20
Electrical
Denitions & Wiring Diagram ��������������������������������������� 21
Festoons ������������������������������������������������������������������������������ 22
Receptacles ������������������������������������������������������������������������ 23
Ceiling Power Entry ��������������������������������������������������������� 24
Base Power Entry ������������������������������������������������������������� 25
Base Cover �������������������������������������������������������������������������� 26
Connector Trim ����������������������������������������������������������������� 27
Finished End Trim ������������������������������������������������������������ 28
Upper Storage
Shelves ��������������������������������������������������������������������������������� 29
Flipper Door ���������������������������������������������������������������������� 30
Worksurfaces
Corner, Extended Corner, 120° & 135° ����������������������� 31
Rectangular ������������������������������������������������������������������������ 32
Transaction ������������������������������������������������������������������������� 33
Lower Storage
Pedestals ���������������������������������������������������������������������������� 34
Lateral Files ������������������������������������������������������������������������ 35
Accessories
Panel-Mounted Tackboard & Markerboards ���������� 37
Tool Bars ������������������������������������������������������������������������������ 38
Cord Managers ������������������������������������������������������������������ 39
LED Tasklight �������������������������������������������������������������������� 40
General Information������������������������������������������������������������������������������������������������������������������������������������������������������������������������������ 4
Safety & Support������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������ 5
Installation Tools ������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������ 6
Staging & Installation ��������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 7

4
GENERAL INFORMATION
This installation manual provides necessary information for the
safe installation of Friant’s Verity product.
The System 2 product line is a modular panel system composed
of panels, hanging and freestanding components and accessories
designed to be precisely tailored to the ofce environment� It
consists of products that are factory assembled and require
installation only; and other products that are shipped as
subassemblies for assembly during the installation process�
System 2 products are available with an 8-wire electric system that
is listed with Underwriters Laboratories and comply with UL1286�
This product is considered portable furniture and is therefore subject
to local re, electrical and building codes; therefore, check with local
building authorities before installation of the product�
It is the responsiblity of the dealer and the installer to properly
install this product according to this manual and generally accepted
industry practices�
WARNING: Failure to follow
the instructions in this manual
can result in product damage,
personal injury or both�
WARNING: Installation
of electrical components
should be done by a qualied
electrician� Disconnect power
prior to servicing the system�

System 2 Installation Manual 5
SAFETY & SUPPORT
SUPPORT CENTER
Should you have any questions or require
assistance during the installation process,
please telephone our support center:
PHONE (510) 535-5113
HOURS Monday - Friday, 8am - 5pm PST
SAFETY NOTES
Please read all WARNINGS and NOTES, as these are for
your safety�
Please read TIPS in the installation as helpful
suggestions�
Always use proper tools when installing�
Keep your work area clean, clutter-free and safe
during installation�
Use eye protection when working under a
workstation or when working with tools�
Many products weigh more than 35 pounds� Use
two or more people to safely lift, carry and install
the products�
When using tools, extension cords or ladders, use
them in accordance to OSHA guidelines�
Work safe, work smart�

6
INSTALLATION TOOLS
INSTALLATION TOOLS
The following tools are necessary for eld assembly
and installation of Friant’s Novo product:
Allen wrench 1/4”
#2 Phillips head screwdriver
#3 Phillips head screwdriver
Screwdriver, med slotted
Measuring tape (25’ or more)
Rubber mallet or dead blow mallet
Carpenter’s level (48”)
The following tools will help speed up installations,
but are not necessary:
Drill (12v or more)
Set of drill bits
Set of screw bits #2 and #3
1/4” Allen bit for drill
Wrench, open end 10mm (long handle is best)
Pliers
Carton knife
Ratchet head 1/4” allen bit
6’ step ladder
Material handling carts

System 2 Installation Manual 7
STAGING
In an effort to make your project run more
smoothly, the following is recommended:
1� Unload all products into a staging area on your
job site and sort by product number�
2� Check in and count all products for accuracy
and damage prior to the delivery truck leaving�
Note any damages or shortages on the Bill of
Lading before signing�
3� Notify the factory immediately of any
shortages or damages (with photo to
document)�
4� Keep and maintain a clutter-free staging area
— it will help speed up your assembly�
5� Protect all building walls with furniture pads
or cardboard where product is leaning against
them or in high trafc areas�
FOR SUCCESSFUL INSTALLATION
Keep these items in mind while installing product:
Ensure that all products are level throughout
the installation process and correctly attached�
Check panels for stability after installation of
all components� If needed, correct or adjust
leveling or installation to x stability�
If needed, add additional support to panels to
ensure stability�
STAGING & INSTALLATION

8
PANELS & CONNECTORS
A panel run is any combination of two or more panels connected in a
straight line�
Panels mounted at right angles to panel runs are called support panels�
The minimum height for support panels should not be less than half the
height of the tallest panel in the panel run� (Example: An 85” high panel
run should have a minimum of a 47” support panel)
Load bearing walls, also known as structural walls, are constructed of
materials such as poured concrete, concrete block or drywall, properly
attached to metal or wood studs� Drywall must be at least 5/8” thick� Wall
must be restrained at the oor and ceiling, and should be no more than
24” on center or 14’ high� Under no circumstances does Friant accept
responsibility for determination of the structural integrity of a load bearing
wall�
A loaded panel run is any panel run that has product component of any
kind attached to it� Also known as “load bearing side of a panel wall”�
DEFINITIONS

System 2 Installation Manual 9
PANELS & CONNECTORS
PANEL TO CONNECTOR — SAME HEIGHT
Connecting a Panel to a Connector
1. Using a 2, 3 or 4 way connector, loosen the draw block
at the top (nished end) of the connector with your allen
wrench� IMAGE A
2. Attach connector to the panel� The connector should
easily t over the panel wedge blocks on the end of your
rst panel� IMAGE B
3. Tighten connector onto panel� IMAGE C
4. Install connector top cap�
TIP: Start at a right angle
condition in your layout� It is
recommended that you identify
the location using your plan to
locate the connection in the
ofce area�
NOTE: All panels with electrically interconnected
panels must be mechanically interconnected�
Connecting a Second Panel
1. Add a second panel onto the connector by loosening the
other draw block at the top of the connector� IMAGE A
2. Attach panel to connector to begin your rst panel run�
Install the panel in a similar manner to above� IMAGE B
3. Tighten connector to panel� IMAGE C
4. You now have the start of your rst station�
A
B
C

10
PANELS & CONNECTORS
PANEL TO CONNECTOR — CHANGE OF HEIGHT
1. When installing a change of height connection, you must
remove the black ller strip on the side of the connector
you are going to attach the panel to� Always use the
connector for the tallest panel you are attaching to�
2. To remove the ller strip, squeeze it at one end and pull
toward you� IMAGE A
3. Remove the connector top cap by pressing gently on the
location pin to release it� IMAGE B
4. Remove the top block assembly� IMAGE C
5. Using the back of the ller strip, push the threaded plate
on to the sticky tape (align to t in connector)� IMAGE D
6. Using the ller strip as your guide, insert the threaded
plate into the connector to the desired height connection�
IMAGE E
7. Reinstall the connector top wedge block using the existing
screws and parts� When the wedge block is securely
tightened in place, gently pull the ller strip to release it�
IMAGE F
8. Using a carton knife or a cutting tool, cut the ller strip to
the appropriate length and reinstall the ller strip on the
connector�
9. Attach the connector to the shorter panel� IMAGE G
NOTE: It is recommended to have two people for
this part of the installation�
10. Tighten the panel wedge block� IMAGE I
AB
C
G
D
H
E
I
F
WARNING: Make sure all wedge
blocks and connectors are
installed properly and securely
before going on to the next part
of the installation�
Inhaltsverzeichnis
Andere Friant Büroausstattung Handbücher
Beliebte Büroausstattung Handbücher anderer Marken

silen
silen Space 2 Bedienungsanleitung

Middle Atlantic Products
Middle Atlantic Products LD Series Bedienungsanleitung

SHFL
SHFL DECK MATE BLACKJACK Bedienungsanleitung

DROMEAS
DROMEAS LINE Bedienungsanleitung

Siemens
Siemens HIPATH 2000 Bedienungsanleitung

VITRA
VITRA Stefan Hürlemann Dancing Wall Bedienungsanleitung













