Frigidaire FAH10ES2TA12 Bedienungsanleitung

Installation instructions

Do This First

(for existing sleeve)

Note that the air conditioner dimensions are: 24.wide,

14½.high, and 18½. deep (without front). Install Air

Conditioner according to these installation instructions

to achieve the best performance. Save these installation

instructions for future reference.

Items in Kit

You may not need all parts in the kit. Discard unused

pans. Qty.

Tapered Spacer Blocks 17,,Long 2

Centering/Support Blocks 4½.x 3½.x 1½. 4

Plastic Divider 1/8" x 4½.x 14½,, 2

Stuffer Seal 1. x 1½"x 84,, 1

Seal 1½.x 1½.x 25,, 3

Seal 1½,,x 1½.x 14,, 2

Seal 1½.x 3/8.x 25. 3

Seal 1½.x 3/8.x 14,, 2

Seal 1" x 3/4.x 14,, 2

Trim Frame (side legs) 2

Trim Frame (top & bottom legs) 2

Ground Wire (green) 1

Nut for grounding screw 1

Grounding Screw 1

Grille (plastic) 1

Grille Aluminum 1

Nuts (plastic) 4

Screw w/washer 4

How to Install

1. identifythe wall-sleeve brandfor your installation,

from the chart below.

Brand

White-Westinghouee

Frigidaire

Carrier (52F Series)

General Electric/

Hotpoint

Whirlpool

Wall Sleeve Dimensions

(inches)

Width Height Depth

}25½ 15¼ 17½

16,

or 22

26 15%

25¼ 16½

Fedders/Emerson 27 16¾

16'/,

17½

or 23

16¾

or 19¾

18%

16¾

Sears/Kenmore 25¾ 16½

Emerson/Fedders 26¾ 15¾

Carrier (51S Series) 25¾ 167/,

Friedrich 27 16¾

NOTE: All wall sleeves used to mount the new Air

Conditioner must be in sound structural condition and

have a rear grille that securely attaches to sleeve, or

rear flange that serves as a stop for the Air Conditioner.

CAUTION: When installation is complete, replacement

unit MUST have a rearward

slope as shown. 1/4" 1o 5/16"

81eeve

REAR

2. Remove old Air Conditioner from wall sleeve and

prepare wall sleeve as follows:

-- Clean interior (do not disturb seals).

-- Wall sleeve must be securely fastened in wall before

installing Air Conditioner. Drive more nails or screws

through sleeve, into wall, if needed.

-- Repair paint if needed.

3. If not existing, drill a 3/16.clearance hole for ground-

ing screw through left side of wall sleeve, in a clear area

about 3 inches maximum (to suit) back from front edge

of sleeve as shown below. Next attach ground wire inside

sleeve, using grounding screw, nut washer pull loose

end of ground wire out front of sleeve, and temporarily

bend it down and around lower edge of sleeve.

Wall sleeve to unit

sleeve grounding

3/16"

FHole

4. Prepare the wall sleeve for installation of the new unit

per the following Brand instructions.

#1 Emerson

#2 Fedders

#3 Fedders or Friedrich

#4 General Electric/Hotpoint

#5 Sears or Carrier (51S Series)

#6 Whirlpool

#7 Whirlpool

#8 White-Westinghouse/Frigidaire/

Carrier (52F Series)

#9 White-Westinghouse/Frigidaire

15"Deep

l_A,,Deep

16¾,,Deep

16¼,,Deep

18%,,Deep

17'_,,Deep

23.Deep

16,,+ 17½.Deep

22"Deep

5. Install new unit into wall sleeve.

6. To attach ground wire to the new unit, remove the

screw from the left side front.

7.Assemble and installthe

Trim Frame (see instruction).

P/N 66129901165

This unit's increased performance characteristics result from having two rear air intakes,

it is very important that these installation instructions are followed so your unit can operate at maximum

efficiency,

if this is an existing sleeve, and there is an existing rear grille, it needs to be replaced by the ones

shipped with the unit in the accessory kit.

EITHER

1. Remove the existing grille.

2. Place the included aluminum grille towards the rear of the unit.

3. Mark through the hole positions.

4, Drill through the sleeves flanges with a 1/8" drill bit,

5, Attach the new grille with self-threading screws and washers (not included),

6, It is VERY iMPORTANT that the grille is placed exactly as shown,

1, Remove the existing grille.

2, Use Plastic grille and secure to sleeves flanges using existing screws and washers,

Wall Sleeve Brands: #1 Emerson 15"Deep

TopView

1. Redirectthelouversatthebackofthewallsleeveas shown

opposite.The useofpliersisrecommended.

2. Attach (1) 1 ½" x 3/8" x 25" longseal inthe center at the

top of the sleeve. Remove _e backing paper and press

into position.

3, Attach (2) 1 ½" x 3/8" x 14" seals to the left and rightsides

of the sleeve.

4. Cut (2) 1½" x 3/8" x 25_long seals to 14"long each

and attach to the vertical sections of the grilleas shown.

5. Attach (2) 4 ½" x3½" x I !/2"centering/support blocks

one on each side wall. Place in center of side wall with

the tapered end facing the opening.

6. Gently slide unitintosleeve.

7. Before slidingall-the-way back, remove 2rid screw from

fronton left side of unit.

8. Remove the plasticwasher from the screw.

9. Screw and attach the other end of the groundwire to

the unitas shown in picture. Make sure that the toothed

washer is against the cabinet.

10. Slide the unitcompletely to the rear to ensure agood

seal, making sure the ground wire does not become

tangled.

11. Seal & Frame the unitas described on the last page of

these instructions.

Wall Sleeve Brands: #2Fedders 19 _" Deep

RearLoavam

ao_\ 3.5 eo. _3

TopView

/I_O*

1. Redirect the louvers at the back of the wall sleeve as shown

opposite. The use of pliers is recommended.

2. Attach (2) 4 ½" x 3 ½" x 1 ½" centering/supportblocks one

on each side wall. Place in center of side wall with the

tapered end facing the opening,

3, Cut (2) 17"Tapered Spacer Blocksas shown below into

two pieces.

4, The 4" section is pieced in frontof the ribon base with the

tapered end facing the back of the sleeve. The remaining

portion will be placed behind the rib again slopingtoward

the rear of the sleeve. This helps induce a rearward elope

on bheunit,

5oAttach (1) 1 _" x 3/8" x 25" longseal in the center at the

top of the sleeve. Remove the backing paper and press

into position.

6, Attach (2) 1 ½" x3/8" x 14" seals to the left and rightsides

of the sleeve,

7, Cut (2) 1½" x3/8" x 25" long seals to 14" long each

and attach to the vertical sections of the grilleas shown.

8. Gently slide unitinto sleeve.

9. Before slidingall-the-way back, remove 2nd screw fl'om

front on leftside of unit.

10. Remove the plastic washer from the screw.

11. Screw and attach the other end of the ground wire to

the unitas shown in picture.Make sure that the toothed

washer is against the cabinet.

12, Slide the unit completely to the rear to ensure a good seal,

making sure the ground wire does not become tangled.

13, Seal & Frame the unitas described on the last page of

these instructions.

#3 Fedders or Friedrich 16 %" Deep

1. Redirect the louvers at the back of the wall sleeve as shown

opposite. The use of pliers is recommended.

2. Attach (2) 4 ½" x3½" x 1 ½" centering/supportblocks one on

each side wall. Place in center of sidewall withthe tapered

end facing the opening.

3. Cut (2) 17" Tapered Spacer Blocksas shown below intothree

pieces.

4, The 2 ½" section is placed in front of the rib on base with the

tapered end facing the back of the sleeve. Cut the remaining

portionto 12 ½" and place behind the rib again sloping toward

the tear of the sleeve. This helps induce a rearward slope on

the unit,

5. Attach (1) 1 ½" x 3/8" x 25" longseal in the center at the

top of the sleeve. Remove the backing paper and press

into position.

6, Attach (2) 1 ½" x3/8" x 14" seals to the left and rightsides

of the sleeve,

7, Cut (2) 1½" x 3/8" x 25" long seals to 14" longeach

and attach to the vertical sections of the grille as shown.

8. Gently slide unitinto sleeve.

9. Before slidingall-the-way back, remove 2nd screw from front

on left side of unit.

10. Remove the plastic washer from the screw.

11. Screw and attach the other end of the ground wire to the

unit as shown in picture. Make sure that the toothed washer

is against the cabinet,

12, Slide the unit completely to the rear to ensure a good seal,

making sure the ground wire does not become tangled.

13, Seal & Frame the unitas described on the last page of

these instructions.

Wall Sleeve Brands: #4 General El ,-tra/Hotpoint 16 7/8" Deep

Louvom

T{_V_w

1. Redirect the louvers at the back of the wall sleeve as shown

opposite. The use of pliers is recommended.

2. Cut (2) 17"Tapered Spacer Blocksas shown below intotwo

pieces. 1_- ,

3. Install as shown withthe tapered end ½" from the back of the

sleeve, This helps induce a rearward slope on the unit.

4. Attach (1) 1 ½" x 3/8" x 25" longseal in the center at the top

of the sleeve. Remove the backing paper and press into

position.

5. Attach (2) 1 ½" x 3/8" x 14" seals to the left and rightsides

of the sleeve.

6, Cut (2) 1½_x 3/8" x 25" long seals to 14" long each

and attach to the vertical sections of the grille as shown,

7, Center unit& gently slide unit into sleeve.

8. Before slidingall-the-way back, remove 2rid screw from front

on left side of unit.

9. Remove the plasticwasher from the screw.

10. Screw and attach the other end of the ground wire to the

unitas shown in picture. Make sure that the toothed washer

is against the cabinet,

11, Slide the unit completely to the rear to ensure a good seal,

making sure the ground wire does not become tangled.

12. Seal & Frame the unitas described on the last page of

these instructions.

WaJJ SJeeve Brands: #5 Sears or Carrier 51S Series 185/8. Deep

TopView

\1. Redirect the louvers atthe back of the wall sleeve as shown

opposite. The use of pliers is recommended.

2. Install (2) tapered spacer blocksto the floor of the sleeve as

shown. DO NOT CUT THESE BLOCKS. This helps induce

a rearward slope on the unit.

3. Install as shown with the tapered end ½" from the back of the

sleeve, This helps induce arearward slope on the unit.

4. Attach (1) 1 ½" x 3/8" x 25" long seal in the center at the top

of the sleeve. Remove the backing paper and press into

position.

5. Attach (2) 1 ½" x 3/8" x 14" seals to the left and rightsides

of the sleeve.

6.Cut (2) 1½" x3/8" x25" long seals to 14" long each

and attach to the vertical sections ofthe grilleas shown.

7. Center unit & gently slide unitinto sleeve.

8. Before sliding all-the=way back, remove 2nd screw from fi'ont

on leftside of unit.

9. Remove the plasticwasher _'om the screw,

!0. Screw and attach the other end of the ground wireto the

unitas shown inpicture, Make sure that the toothed washer

isagainst the cabinet.

11, Slide the unitcompletely to the rear to ensure a good seal,

making sure the groundwire does not become tangled,

12. Seal & Frame the unitas described on the last page of

these instructions.

Wall Sleeve Brands: #6Whirlpool 17 1/8" Deep

Lou_am

_1_ 3"5'_I _o _

Top_ew

F4_O=

1. Redirect the louvers at the back of the wall sleeve as shown

opposite. The use of pliers is recommended.

2. Cut (2) 17"Tapered Spacer Blocksas shown below into

two pieces. _

3. install to the floor of the sleeve as shown.This helps

induce arearward slope on the unit,

4. Attach (1) 1 ½" x 3/8" x 25" longseal in the center at the

top of the sleeve. Remove the backing paper and press

into position.

5. Attach (2) 1 ½" x 3/8" x 14" seals to the left and right

sides of the sleeve.

6.Cut (2) 1½" x 3/8" x 25" longseals to 14" long each

and attach to the vertical sections of the grilleas shown.

7. Center unit& gently slide unit into sleeve.

8. Before slidingall-the-way back, remove 2rid screw from front

on left side of unit.

9. Remove the plasticwasher from the screw.

10. Screw and attach the other end of the ground wire to the

unitas shown in picture. Make sure that the toothed washer

is against the cabinet.

11. Slide the unit completely to bherear to ensure a good seal,

making sure the ground wire does not become tangled.

12. Seal & Frame the unitas described on the last page of

these instructions.

Wall Sleeve Brands: #TWhirlpool 23. Deep

I_ LOgVeI_

GOoGOo

\\ \ \ \_ _////JJ/J \\_\\_\_\\I/111//

TopView

f 80°

1. Redirect the louvers at the back of the wall sleeve as shown

opposite. The use of pliersis recommended.

Because of the increased unit depth, first try dry fitting

using the method described below:

1. Place (2) 1 ½" x 1 ½" x 14" seals against each side.

2. Gently slide unitin and check if amount extending from the

sleeve issufficient once the trim frame is attached.

3. If position is okay, remove unitand Proceed to the next step.

If not go to step 8.

4. Attach (1) 1 ½" x 1_'2"x 25" long seal in the center at the

top of the sleeve. Remove the backing paper and press into

position.

5. Attach (2) 1 ½" x 1 _'2"x 14" seals to the left and rightsides

of the sleeve.

6. Cut (2) 1½" x 3/8" x 25" long seals to 14" longeach

and attach to the vertical sections of the grilleas shown.

7. Attach the tapered spacer blocksto the floor of the sleeve.

Now go to step 13.

Use these next steps if the unit requires extra extension

into the room.

8. Attach 1"x %"x14" long seal over the solid vertical portion

of the rear grille.

9. Attach (2) 4 ½" x3½" x1½" foam blocks with the slot

overlapping the seal above.

10. installthe divider intothe slots of the foam blocks. You may

need to trim the length to size.

11. Repeat steps 8-10 for the other vertical shown portion of

the grille as shown in the picture

12. Cut the 1 ½" x 1 !/2"x 25" seal to fit the top of the sleeve.

The pieces must be fitted flush to the edge of the divider.

13. Attach (2) 1 V2"x 1 ½" x 14" seals along the sides of the

sleeve again making sure all seals are flush.

14. Center unit & gently slide unit intosleeve.

15. Before sliding all-the-way back, remove 1st screw from

front on left side of unit.

16. Remove the plasticwasher from the screw.

17. Screw and attach the other end of the ground wire to the

unit as shown in picture. Make sure that the toothed washer

is against the cabinet.

18. Slide the unit completely to the rear to ensure a good seal,

making sure the ground wire does not become tangled.

19. Seal & Frame the unitas described on the last page of

these instructions.

Wall Sleeve Brands: #8 White Westinghouse/Frigidaire/

Carrier 52FSeries 16" + 17 ½" Deep

=If the wall sleeve does not have arear grilleor Iouvered

panel, installthe plasticgrillefrom the kit. The plastic

grille is mounted to the inside of the wall sleeve at the rear

flanges. There are (4) plastic nuts in the tlanges ofthe wail

sleeve. If some are missingreplacements are included in

the accessory kit, and can be simply pressed intothe square

holes inthe flanges. Place the grUieagainst the rear flanges

and use the (4) large washers and screws to secure the grille.

2. Attach (1) 1 ½" x 3/8" x 25" long seal inthe center at the top

of the sleeve. Remove the backing paper and press into

position.

3. Attach (2) 1 ½" x3/8" x 14" seals to the left and rightsides

of the sleeve.

4. Attach (1) 1"x _'x 14" long seal vertically 3.5" from the left

side of the sleeve. Attach the other 1_x%"x 14" longseal 3"

from the right side of the sleeve

5. Center unit& gently slideunit into sleeve.

6. Before sliding all-the-way back, remove 2nd screw from front

on left side of unit.

7. Remove the plastic washer from the screw,

8. Screw and attach the other end of the ground wire to the

unit as shown in picture. Make sure thatthe toothed washer

is against the cabinet.

9. Slide the unitcompletely to the rear to ensure a good seal,

making sure the ground wire does not become tangled.

10. Seal & Frame the unitas described on the last page of

these instructions.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Frigidaire Klimaanlage Handbücher

Frigidaire

Frigidaire CRA054XT7 Betriebsanleitung

Frigidaire

Frigidaire FAS224J2A2 Bedienungsanleitung

Frigidaire

Frigidaire FAA055P7AB Bedienungsanleitung

Frigidaire

Frigidaire CRA065AT711 Betriebsanleitung

Frigidaire

Frigidaire FRA122BU1 Bedienungsanleitung

Frigidaire

Frigidaire GAH085Q1T - GIBSON 8000BTU 115V 8.0A 9.4EE3 SPD 4 WAY AIR... Bedienungsanleitung

Frigidaire

Frigidaire Home Comfort FRA123PT1 Montageanleitung

Frigidaire

Frigidaire FAS155P1A1 Bedienungsanleitung

Frigidaire

Frigidaire FRA106CV1 Bedienungsanleitung

Frigidaire

Frigidaire FAK124Q1 Bedienungsanleitung

Frigidaire

Frigidaire 220218A007 Bedienungsanleitung

Frigidaire

Frigidaire FAC053J7A1 Bedienungsanleitung

Frigidaire

Frigidaire FAS182P2A1 Bedienungsanleitung

Frigidaire

Frigidaire FAS256R2A - 25,000-BTU Window Air... Bedienungsanleitung

Frigidaire

Frigidaire FAH096J2T2 Bedienungsanleitung

Frigidaire

Frigidaire FHWW083WBE Betriebsanleitung

Frigidaire

Frigidaire FAC066L7A2 Bedienungsanleitung

Frigidaire

Frigidaire FRA053XT71 Betriebsanleitung

Frigidaire

Frigidaire FAC084K7A4 Bedienungsanleitung

Frigidaire

Frigidaire FAH086S1T - Through The Wall Room Air... Bedienungsanleitung

Frigidaire

Frigidaire FAA087S7AF Bedienungsanleitung

Frigidaire

Frigidaire FAK083J7V4 Bedienungsanleitung

Frigidaire

Frigidaire FAC127S1A11 Bedienungsanleitung

Frigidaire

Frigidaire FRA106CV1 Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung

Carrier

Carrier 42HVM109303 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Mr.Slim PUZ-SM100VKA Bedienungsanleitung

Airwell

Airwell Dakota DCI Series Bedienungsanleitung