FRONIUS Robacta Reamer V 70 Han12P Bedienungsanleitung

Fronius prints on elemental chlorine free paper (ECF) sourced from certified sustainable forests (FSC).

/ Perfect Charging / Perfect Welding / Solar Energy

Robacta Reamer V 70 Han12P

Operating instructions

Welding torch cleaning

42,0426,0220,EN 008-21092020

Contents

Safety rules 5

General 5

Proper use 5

Environmental conditions 5

Obligations of the operator 6

Obligations of personnel 6

Specific hazards 6

Protecting yourself and others 7

EMC Device Classifications 7

EMC measures 7

EMF measures 8

Safety measures at the installation location and during transport 8

Safety measures in normal operation 8

Commissioning, maintenance and repair 9

Safety inspection 9

Disposal 9

Safety symbols 9

General 11

General 13

Principle 13

Device concept 13

Application areas 13

Warning notices on the cleaning device 13

Transport 16

Transport devices 16

Transport notices on the packaging 16

Scope of supply and options 17

Scope of supply 17

Available options 17

Controls, connections and mechanical components 19

Safety 21

Controls, connections and mechanical components 22

Control elements, connections and mechanical components 22

Harting Han12P connecting plug (X1) pin assignment for robot control 24

General 24

Harting Han12P connecting plug (X1) pin assignment 24

Installation and commissioning 25

Safety 27

Ensuring that the cleaning device is depressurised 28

Before commissioning 29

Proper use 29

Operators, maintenance personnel 29

Setup regulations 29

Compressed air supply specifications 29

Measures for the safe operation of the device with untrained personnel 30

Screwing the cleaning device to the underlying surface 31

Screwing the cleaning device and installation stand to the underlying surface 31

Screwing the cleaning device to the underlying surface 31

Torch cleaning position 33

Welding torch cleaning position 33

Adjust gas nozzle clamping device 34

Adjusting the gas nozzle clamping device 34

Fitting the cleaning cutter 35

Adjusting the position of the cleaning motor 36

Configuring the spray device 37

Installing the electrically controlled wire cutter (optional) 38

How the electrically-controlled wire cutter works 38

Maximum wire diameter 38

Installing the electrically controlled wire cutter 38

To establish the compressed air supply: 40

Establishing the compressed air supply for the cleaning device, function of the compressed air

relief valve

Starting up the parting agent nebuliser 41

Filling the parting agent container (1 litre) and connecting it to the cleaning device 41

Connecting the parting agent container (10 litres) to the cleaning device 42

Adjusting the parting agent nebuliser spray amount 43

Manually checking the cleaning device functions 44

Safety 44

Manually checking the cleaning device functions 44

Starting up the cleaning device 46

Prerequisites for start-up 46

Start-up 46

Cleaning programme 47

Safety 47

Cleaning program sequence 48

Signal waveform for cleaning 52

Signal inputs 52

Signal outputs 52

Signal waveform optional wire cutter (input) 52

Care, maintenance and disposal 53

Safety 55

Ensuring that the cleaning device is depressurised 56

Care, maintenance and disposal 57

General 57

Before each start-up 57

Daily 57

Weekly 57

Every 6 months 57

As necessary 57

Disposal 58

Troubleshooting 59

Safety 61

Ensuring that the cleaning device is depressurised 62

Troubleshooting 63

Errors in program sequence 63

Technical data 65

Technical data 67

Robacta Reamer V 70 Han12P 67

Appendix 69

Robacta Reamer V 70 Han12P Circuit Diagram 70

Robacta Reamer V 70 Han12P pneumatic diagram 71

Declaration of conformity 72

Safety rules

General The device is manufactured using state-of-the-art technology and according to recog-

nised safety standards. If used incorrectly or misused, however, it can cause:

- injury or death to the operator or a third party,

- damage to the device and other material assets belonging to the operating com-

pany,

- inefficient operation of the device.

All persons involved in commissioning, operating, maintaining and servicing the device

must:

- be suitably qualified,

- have sufficient knowledge of automated welding, and

- read and carefully follow these operating instructions as well as the operating

instructions for all system components.

The operating instructions must always be at hand wherever the device is being used. In

addition to the operating instructions, attention must also be paid to any generally applic-

able and local regulations regarding accident prevention and environmental protection.

All safety and danger notices on the device

- must be in a legible state,

- must not be damaged,

- must not be removed,

- must not be covered, pasted or painted over.

For the location of the safety and danger notices on the device, refer to the section

headed "General" in the operating instructions for the device.

Before commissioning the device, rectify any faults that could compromise safety.

This is for your personal safety!

Proper use The device is to be used exclusively for its intended purpose.

The device is intended solely for the mechanical cleaning of Fronius robot welding

torches in automatic mode.

Any use above and beyond this purpose is deemed improper. The manufacturer shall not

be held liable for any damage arising from such usage.

Proper use includes:

- carefully reading these operating instructions

- following all the instructions and safety rules in these operating instructions

- performing all stipulated inspection and maintenance work

The device is designed for use in industry and the workshop. The manufacturer accepts

no responsibility for any damage caused through use in a domestic setting.

The manufacturer likewise accepts no liability for inadequate or incorrect results.

Environmental

conditions

Operation or storage of the device outside the stipulated area will be deemed as not in

accordance with the intended purpose. The manufacturer shall not be held liable for any

damage arising from such usage.

Ambient temperature range:

- during operation: 0 °C to + 40 °C (32 °F to 104 °F)

- during transport and storage: -25 °C to +55 °C (-13 °F to 131 °F)

Relative humidity:

- up to 50 % at 40 °C (104 °F)

- up to 90 % at 20 °C (68 °F)

Keep ambient air free from dust, acids, corrosive gases and substances, etc.

Can be used at altitudes of up to 2000 m (6500 ft)

Obligations of the

operator

The operator must only allow persons to work with the device who:

- are familiar with the fundamental instructions regarding safety at work and accident

prevention and have been instructed in how to use the device

- have read and understood these operating instructions, especially the section

"safety rules", and have confirmed as much with their signatures

- are trained to produce the required results.

Checks must be carried out at regular intervals to ensure that operators are working in a

safety-conscious manner.

Obligations of

personnel

Before using the device, all persons instructed to do so undertake:

- to observe the basic instructions regarding safety at work and accident prevention

- to read these operating instructions, especially the "Safety rules" section and sign to

confirm that they have understood them and will follow them.

Before leaving the workplace, ensure that people or property cannot come to any harm

in your absence.

Specific hazards Stay out of the working area of the robot.

The device must be incorporated into a higher-level safety system within a secured area.

If this area has to be accessed when setup and maintenance work is carried out, make

sure that

- the entire system is switched off for the duration of the work in this area

- and that it is prevented from starting up accidentally, e.g. as the result of a control

fault.

If untrained operators have access to the device, its compressed air supply must be dis-

connected for the duration of work in accordance with "Performance Level d" of the ISO

13849-1 standard.

In addition to these Operating Instructions, the safety rules issued by the robot manufac-

turer must also be observed.

Keep your body, especially your hands, face, hair, clothing and all tools away from mov-

ing parts, such as:

- rotating cleaning cutter

- upwards/downwards travelling cleaning motor

- extending/retracting gas nozzle clamping device

- wire cutter

Do not touch cleaning cutters immediately after use - risk of burns. Observe the special

safety rules in the Operating Instructions for handling cleaning cutters.

Protect hands, face and eyes against flying parts (shavings, etc.) and compressed air/

parting agent mixture escaping from the parting-agent injection nozzle.

Covers may only be opened/removed for the duration of any maintenance, installation or

repair work.

During operation

- Ensure that all covers are closed and fitted properly

- Keep all covers closed

Protecting your-

self and others

Anyone working with the device exposes themselves to numerous risks. In addition to

these Operating Instructions, the safety rules of the manufacturer of the entire welding

system must also be observed.

Keep all persons, especially children, out of the working area while any devices are in

operation or welding is in progress. If, however, there are people in the vicinity:

- Make them aware of all the dangers and health risks (crushing from mechanically-

powered parts, injury from cleaning cutter, flying shavings and similar matter, escap-

ing compressed air/parting agent mixture, flying sparks, dazzling by arc, inhaling of

harmful welding fumes, noise, possible danger from mains or welding current, etc.)

- Provide suitable protective equipment

- Alternatively, erect suitable safety screens/curtains

EMC Device Clas-

sifications

Devices in emission class A:

- Are only designed for use in industrial settings

- Can cause line-bound and radiated interference in other areas

Devices in emission class B:

- Satisfy the emissions criteria for residential and industrial areas. This is also true for

residential areas in which the energy is supplied from the public low-voltage mains.

EMC device classification as per the rating plate or technical data.

EMC measures In certain cases, even though a device complies with the standard limit values for emis-

sions, it may affect the application area for which it was designed (e.g. when there is

sensitive equipment at the same location, or if the site where the device is installed is

close to either radio or television receivers).

If this is the case, then the operator is obliged to take appropriate action to rectify the

situation.

Check for possible problems, and check and evaluate neighbouring devices' resistance

to interference according to national and international requirements:

- Safety devices

- Power, signal and data transfer lines

- IT and telecommunications devices

- Measuring and calibrating devices

Supporting measures for avoidance of EMC problems:

1. Mains supply

- If electromagnetic interference arises despite correct mains connection, addi-

tional measures are necessary (e.g. use a suitable line filter).

2. Control lines

- must be kept as short as possible

- must run close together (to avoid EMF problems)

- must be kept well apart from other leads

3. Equipotential bonding

4. Shield, if necessary

- Shield off other nearby devices

- Shield off entire welding installation

EMF measures Electromagnetic fields may pose as yet unknown risks to health:

- effects on the health of others in the vicinity, e.g. wearers of pacemakers and hear-

ing aids

- wearers of pacemakers must seek advice from their doctor before approaching the

device or any welding that is in progress

- for safety reasons, keep distances between the welding cables and the welder's

head/torso as large as possible

- do not carry welding cables and hosepacks over the shoulders or wind them around

any part of the body

Safety measures

at the installation

location and dur-

ing transport

A device toppling over could easily kill someone. Place the device horizontally on a level,

firm and solid surface and anchor it securely to prevent it toppling over.

Special regulations apply in rooms at risk of fire or explosion

- Observe relevant national and international regulations.

Use internal directives and checks to ensure that the workplace environment is always

clean and clearly laid out.

When transporting the device, observe the relevant national and local guidelines and

accident prevention regulations. This applies especially to guidelines regarding the risks

arising during transport.

After transporting the device, it must be visually inspected for damage before commis-

sioning. Any damage must be repaired by trained service technicians before commis-

sioning the device.

Safety measures

in normal opera-

tion

Only operate the device if all safety devices are fully functional. If the safety devices are

not fully functional, there is a risk of

- injury or death to the operator or a third party,

- damage to the device and other material assets belonging to the operator,

- inefficient operation of the device.

Any safety devices that are not functioning properly must be repaired before switching on

the device.

Never bypass or disable safety devices.

Before switching on the device, ensure that no one is likely to be endangered.

Check the device at least once a week for obvious damage and proper functioning of

safety devices.

- Only use suitable original parting agent from the manufacturer.

- Observe the information on the parting agent safety data sheet when handling part-

ing agent. The parting agent safety data sheet may be obtained from your service

centre or downloaded from the manufacturer's website.

- Do not mix the manufacturer's parting agent with other parting agents.

- If damage results from using a different parting agent, the manufacturer accepts no

liability. In addition, no warranty claims will be entertained.

- Used parting agent must be disposed of properly in accordance with the relevant

national and international regulations.

Commissioning,

maintenance and

repair

It is impossible to guarantee that bought-in parts are designed and manufactured to meet

the demands made of them, or that they satisfy safety requirements.

- Use only original spare and wearing parts (also applies to standard parts).

- Do not carry out any modifications, alterations, etc. to the device without the manu-

facturer's consent.

- Components that are not in perfect condition must be replaced immediately.

- When ordering, please give the exact designation and part number as shown in the

spare parts list, as well as the serial number of your device.

The housing screws provide the ground conductor connection for earthing the housing

parts.

Only use original housing screws in the correct number and tightened to the specified

torque.

Safety inspection The manufacturer recommends that a safety inspection of the device is performed at

least once every 12 months.

A safety inspection should be carried out by a qualified electrician

- after any changes are made

- after any additional parts are installed, or after any conversions

- after repair, care and maintenance has been carried out

- at least every twelve months.

For safety inspections, follow the appropriate national and international standards and

directives.

Further details on safety inspection and calibration can be obtained from your service

centre. They will provide you on request with any documents you may require.

Disposal Do not dispose of this device with normal domestic waste! To comply with the European

Directive on Waste Electrical and Electronic Equipment and its implementation as

national law, electrical equipment that has reached the end of its life must be collected

separately and returned to an approved recycling facility. Any device that you no longer

require must either be returned to your dealer or given to one of the approved collection

and recycling facilities in your area. Ignoring this European Directive may have poten-

tially adverse affects on the environment and your health!

Safety symbols Devices with the CE mark satisfy the essential requirements of the applicable directives

(e.g. low-voltage and electromagnetic compatibility directives, machinery directive).

Devices with the CSA test mark satisfy the requirements of the relevant standards in

Canada and the USA.

The text and illustrations are all technically correct at the time of printing. We reserve the

right to make changes. The contents of the operating instructions shall not provide the

basis for any claims whatsoever on the part of the purchaser. If you have any sugges-

tions for improvement, or can point out any mistakes that you have found in the instruc-

tions, we will be most grateful for your comments.

Inhaltsverzeichnis

Andere FRONIUS Schweißsystem Handbücher

FRONIUS

FRONIUS TransTig 170 Bedienungsanleitung

FRONIUS

FRONIUS MTG 400i K4 Bedienungsanleitung

FRONIUS

FRONIUS TWIN Push Bedienungsanleitung

FRONIUS

FRONIUS TRANS STEEL 3500 C0MPACT Leitfaden

FRONIUS

FRONIUS MTG 270i US Bedienungsanleitung

FRONIUS

FRONIUS TS 4000 Bedienungsanleitung

FRONIUS

FRONIUS Ignis 180 TIG Bedienungsanleitung

FRONIUS

FRONIUS TTW 4500 Bedienungsanleitung

FRONIUS

FRONIUS TransPocket 1500 Bedienungsanleitung

FRONIUS

FRONIUS TransPocket 150 Bedienungsanleitung

FRONIUS

FRONIUS Robacta MTG 3500 Bedienungsanleitung

FRONIUS

FRONIUS TransSteel 2700c Bedienungsanleitung

FRONIUS

FRONIUS MTG 250d Bedienungsanleitung

FRONIUS

FRONIUS TransTig 1750 Puls Bedienungsanleitung

FRONIUS

FRONIUS MTB 200i G ML/L268/flex Bedienungsanleitung

FRONIUS

FRONIUS MTG 250d Bedienungsanleitung

FRONIUS

FRONIUS FDV 15 MF Bedienungsanleitung

FRONIUS

FRONIUS DeltaSpot Series Leitfaden

FRONIUS

FRONIUS TransPocket 180 RC HW Bedienungsanleitung

FRONIUS

FRONIUS MagicWave 2600 Bedienungsanleitung

FRONIUS

FRONIUS MagicWave 190 Bedienungsanleitung

FRONIUS

FRONIUS TPS 320i Bedienungsanleitung

FRONIUS

FRONIUS Robacta Reamer V Easy Bedienungsanleitung

FRONIUS

FRONIUS Trans Pocket 4000 CEL Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

ESAB

ESAB Buddy Arc 145 Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

WIA

WIA Weldmatic 270 CP132-2 Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung

FRO­NIUS Robacta Reamer V 70 Han12P Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

FRONIUS Robacta Reamer V 70 Han12P Bedienungsanleitung