FS S1900-16TP Bedienungsanleitung
S1900-16TP
ETHERNET UNMANAGED POE SWITCH
UNMANAGED ETHERNET-POE-SWITCH
SWITCH POE ETHERNET NON GÉRÉ
Quick Start Guide V1.0
Quick-Start Anleitung
Guide de Démarrage Rapide
PWR
15131197531
Link/Act
Isolation
VLAN
CCTV
Standard
Link/Act
PoE
PoE
161412108642
43 65 87 109 1211 13
S1900-16TP PoE+
21
Isolation: Ports 1-8 are isolated with ports 9-16 VLAN: Ports 1-14 are isolation, but can link with ports 15-16
14 1615
Introduction
Accessories
S1900-16TP
Thank you for choosing S1900-16TP switch. This guide is designed to familiarize you with the layout of
the switch and describes how to deploy the switch in your network.
Front Panel Ports
Hardware Overview
1
EN
Screw x6 ( KM3*8mm ) Power Cord x1Rubber Pad x4 Mounting Bracket x2
RJ45/PoE
Description
Ports
RJ45/PoE 10/100/1000BASE-T ports for Ethernet connection. All ports support PoE function.
PWR
15131197531
Link/Act
Isolation
VLAN
CCTV
Standard
Link/Act
PoE
PoE
161412108642
43 65 87 109 1211 13
S1900-16TP PoE+
21
Isolation: Ports 1-8 are isolated with ports 9-16 VLAN: Ports 1-14 are isolation, but can link with ports 15-16
14 1615
PWR
15131197531
Link/Act
Isolation
VLAN
CCTV
Standard
Link/Act
PoE
PoE
161412108642
43 65 87 109 1211 13
S1900-16TP PoE+
21
Isolation: Ports 1-8 are isolated with ports 9-16 VLAN: Ports 1-14 are isolation, but can link with ports 15-16
14 1615
Front Panel
Solid on
PWR
RJ45
PoE
The switch is connected to a power supply properly.
The switch is not connected to a power supply properly or
not connected to a power supply.
The port is connected properly.
The port is transmitting or receiving data.
O
Solid on
Blinking
DescriptionStatusLEDs
The port is not connected properly or not connected to
a device.
A PD is connected to the PoE port and powered properly.
O
Solid on
No PD is connected to the PoE port.O
2
EN
RJ45/PoE
PWR Network Mode Switch
Network Mode Switch:
Set the network mode to the one you need using the network mode switch according to the
following description.
Standard Mode (default):
In this mode, the switch functions as a common switch and all the ports of the switch can
communicate with each other.
CCTV Mode:
In this mode, PoE ports 1-8 have higher priorities over the other ports. All the ports of the switch
can communicate with each other.
Ports 15 and 16 are uplink ports.
If multiple IP cameras are connected to the switch, you are recommended to enable this mode
and connect special supervision IP cameras to the ports with high priority the two uplink ports of
the switch to upstream devices (such as NVR, router, and so on), to ensure smoother monitoring
video playback.
Back Panel
Grounding Point
3
EN
Installation Requirements
Do not operate it in an area that exceeds an ambient temperature of 45°C.
The installation site must be free from leaking or dripping water, heavy dew, and humidity.
Ensure rack and working platforms are well earthed.
The installation site must be well ventilated. Ensure that there is adequate air ow around the
switch.
Be sure that the switch is level and stable to avoid any hazardous conditions.
Do not install the equipment in a dusty environment.
Desktop mounting: ESD bracelet (or ESD gloves)
Rack mounting: ESD bracelet (or ESD gloves), Phillips screwdriver, M6 Screws, Standard-sized 19"
wide rack with a minimum of 1U height available.
Wall mounting: ESD bracelet (or ESD gloves), ladder, marker, hammer drill, rubber hammer,
expansion bolts (M5*40mm), screws (PA5*25 mm, head diameter: 10 mm), screwdriver.
Before you begin the installation, make sure that you have the following:
Site Environment:
AC 100-240V 56/60HZ
Power Supply
VLAN Mode:
In this mode, ports 1 to 14 are isolated from each other, but can communicate with ports 15 and
16 (uplink ports) respectively.
And the switch can reduce broadcast storm and isolate DHCP broadcast.
Isolation Mode:
In this mode, ports1 to 8 and ports 9 to 16 belong to two dierent VLAN.
This mode can be used to isolate supervision network and wireless network to make them not
interfere with each other.
4
EN
Desk Mounting
Wall Mounting
1. Attach four rubber pads to the bottom.
2. Place the chassis on a desk.
1. Rotate the two L-shaped brackets by 90 degrees and x them to both sides of the switch with the
included screws.
Mounting the Switch
5
EN
2. Horizontally place the switch onto the wall with its RJ45 ports facing upward. Then mark the screw
holes with the marker.
3. Drill holes in the marked positions, and then knock the expansion bolts (self-prepared,
M5*40 mm) into the holes.
4. Insert the screws (self-prepared, PA5*25 mm, head diameter: 10 mm) through the holes of the two
L-shaped brackets, and secure the screws into the expansion bolts with a screwdriver. Ensure that the
switch is installed rmly with its RJ45 ports facing upward.
NOTE: This switch can only be installed on a concrete or non-ammable wall.
6
EN
1. Secure the mounting brackets to the two sides of the switch with six KM3*8 screws.
2. Attach the switch to the rack using the screws and tighten it.
Rack Mounting
AC 100-240V 56/60HZ
7
EN
Grounding the Switch
1. Connect one end of the grounding cable to a proper earth ground, such as the rack in which the
switch is mounted.
2. Secure the grounding lug to the grounding point on the back of the switch with the washer and
screws.
CAUTION: The earth connection must not be removed unless all supply connections have
been disconnected.
AC 100-240V 56/60HZ
8
EN
Connecting the Power
1. Plug the AC power cord into the power port on the back of the switch.
2. Connect the other end of the power cord to an AC power source.
1. Connect an Ethernet cable to the RJ45 port of a computer, printer, network storage, or other
network devices.
2. Connect the other end of the Ethernet cable to the RJ45 port of the switch.
WARNING: Do not install power cable while the power is on.
Connecting the RJ45 Ports
9
EN
1. Connect an Ethernet cable to the PD devices, such as internet phone, network camera, wireless
access point device.
2. Connect the other end of the Ethernet cable to the RJ45 port of the switch.
Connecting the PD
Inhaltsverzeichnis
Sprachen:
Andere FS Schalten Handbücher
FS
FS S5800 Series Bedienungsanleitung
FS
FS S3700-24T4F Bedienungsanleitung
FS
FS IES5100-24TF Bedienungsanleitung
FS
FS S3410 Series Bedienungsanleitung
FS
FS S5800 Series Bedienungsanleitung
FS
FS S1900-5T Bedienungsanleitung
FS
FS PoE+ Series Bedienungsanleitung
FS
FS S5850-24S2Q-DC Bedienungsanleitung
FS
FS SC9405 Series Bedienungsanleitung
FS
FS S5860 Series Bedienungsanleitung
FS
FS PoE+ Series Betriebsanleitung
FS
FS S5800-48F4SR Bedienungsanleitung
FS
FS S5800-48MBQ Bedienungsanleitung
FS
FS S3700-24T4F Bedienungsanleitung
FS
FS S2805S Series Bedienungsanleitung
FS
FS S3700-24T4F Bedienungsanleitung
FS
FS S3900 Series Bedienungsanleitung
FS
FS S3910 Series Bedienungsanleitung
FS
FS IES3100-8TF-P Bedienungsanleitung
FS
FS S5300-12S Bedienungsanleitung
