FS S5860-20SQ Bedienungsanleitung
MANAGED L2/L3 ENTERPRISE SWITCH
S5860-20SQ
Quick Start Guide V1.1
S5860-20SQ
Introduction
Thank you for choosing S5860-20SQ Switch. This guide is designed to familiarize you with the
layout of the switch and describes how to deploy the switch in your network.
Accessories
Power Cord x2
Mounting Bracket x2 M4 Screw x8
Rubber Pad x4Grounding Cable x1
NOTE: S5860-20SQ switch has dust plugs delivered with it. Keep the dust plugs properly
and use them to protect idle optical ports.
MGMT
CONSOLE 25G
STATUSPWR1 PWR2 FAN MGMT ID
123 4
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 40G Breakout
25
26
S5860-20SQ
40G
FUNC
Hardware Overview
Front Panel Ports
MGMT
CONSOLE 25G
STATUSPWR1 PWR2 FAN MGMT ID
123 4
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 40G Breakout
25
26
S5860-20SQ
40G
FUNC
MGMT
CONSOLE 25G
STATUSPWR1 PWR2 FAN MGMT ID
123 4
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 40G Breakout
25
26
40G
FUNC
S5860-20SQ
USB CONSOLE QSFP+
MGMT
FUNC
SFP+ SFP28
Ports Description
SFP+
SFP28
QSFP+
MGMT
SFP+ ports for 1/10G connection
SFP28 ports for 10/25G connection
QSFP+ ports for 40G or 4x 10G connection
An out-of-band Ethernet management port
CONSOLE
USB
An RJ45 console port for serial management
A USB management port for software and conguration backup
and oine software upgrade
Button Description
FUNC The switch will restart after you press the FUNC button for more
than ve seconds and wait for another ten seconds.
Front Panel Button
MGMT
CONSOLE 25G
STATUSPWR1 PWR2 FAN MGMT ID
123 4
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 40G Breakout
25
26
40G
FUNC
S5860-20SQ
Grounding Point
STATUS/PWR1/PWR2
FAN/MGMT/ID SFP+ SFP28 QSFP+
Fan Slots Dual Power Supplies
Back Panel
FAN1 FAN2 PWR1 PWR2
M1SFANI-F
Status
M1SFANI-F
Status
Front Panel LEDs
Description
The system is powered o.
1. A system fault occurs.
2. The temperature reaches the upper limit.
Initialization is in progress.
The system works properly.
The temperature reaches the threshold value.
O
Solid Red
Blinking Green
Solid Green
Solid Yellow
LEDs
STATUS
The power module is NOT in the position.
The power module works properly.
A power fault occurs.
The MGMT port is NOT connected.
The MGMT port is connected.
The MGMT port is transmitting or receiving
data.
The fan works properly.
1. A fan fault occurs.
2. The fan model does not match with the
system.
3. Not all fans are in position.
O
O
Green
Blinking Green
Solid Green
Solid Green
Solid Red
Solid Red
PWR1/PWR2
FAN
MGMT
Status
Before you begin the installation, make sure that you have the following:
Site Environment:
Description
The locator is controlled by CPLD by default.
The SFP+ port is NOT connected.
The SFP+ port is connected at 1/10G.
The SFP28 port is NOT connected.
The SFP28 port isconnected at 10/25G.
The QSFP+ port is NOT connected.
The QSFP+ port is connected at 10/40G.
The QSFP+ port is transmitting or receiving
data at 10/40G.
The SFP28 port is transmitting or receiving
data at 10/25G.
The SFP+ port is transmitting or receiving
data at 1/10G.
The locator is controlled by O&M personnel
remotely.
O
O
O
O
Solid Green
Blinking Green
Solid Green
Blinking Green
Solid Green
Blinking Green
Solid Blue
LEDs
ID
SFP+
SFP28
QSFP+
Status
Installation Requirements
Phillips screwdriver.
Standard-sized, 19" wide rack with a minimum of 1U height available.
Category 5e or higher RJ-45 Ethernet cables, ber optical cables and console cable for connecting
network devices.
Do not operate it in an area that exceeds an ambient temperature of 50°C.
The installation site must be well ventilated. Ensure that there is adequate airow around the
switch.
The switch should be installed at least 1U (44.45mm) away from devices to its sides.
Be sure that the switch is level and stable to avoid any hazardous conditions.
Do not install the equipment in a dusty environment.
The installation site must be free from leaking or dripping water, heavy dew, and humidity.
Ensure rack and working platforms are well earthed.
Mounting the Switch
Desk Mounting
S5860-20SQ
1. Attach four rubber pads to the bottom.
2. Place the chassis on a desk.
1. Secure the mounting brackets to the two sides of the switch with six M4 screws.
Rack Mounting
1234
40GBreakout
25
26
40G
NOTE: Insert the power module steadily. Please pay attention to the direction of the
power panel to avoid wrong insertion. If the position is not proper, press the plug of the
power module and hold on to the module handle with one hand to pull it out slowly,
then re-insert it.
Installing the Power Supply Module
2. Attach the switch to the rack using four M6 screws and cage nuts.
1. Take a new power module out of the package.
2. Take the plane printed with power information as the top panel of the power module. Hold the
handle of the power module with one hand, and hold the end of the power module with the other
hand. Insert it into the chassis along the guide rail steadily and slowly until a click is heard, and make
sure that it is in good contact with the power slot.
FAN2
PWR2
PWR1
M1SFANI-F
Status
M1SFANI-F
Status
1. Connect one end of the grounding cable to a proper earth ground, such as the rack in which the
switch is mounted.
2. Secure the grounding lug to the grounding point on the switch back panel with the washers and
screws.
Grounding the Switch
FAN1
M1SFANI-F
Status
M1SFANI-F
1. Plug the AC power cord into the power port on the back of the switch.
2. Connect the other end of the power cord to an AC power source.
Connecting the Power
FAN2 PWR1
M1SFANI-F
Status
M1SFANI-F
Status
WARNING: Do not install power cable while the power is on.
PWR2
First install SFP+ transceivers and then connect ber optic cables to the transceiver ports, or directly
connect DAC cables to the SFP+ slots.
Connecting the SFP+ Ports
First install SFP28 transceivers and then connect ber optic cables to the transceiver ports.
Connecting the SFP28 Ports
First install QSFP+ transceivers and then connect ber optic cables to the transceiver ports, or
directly connect DAC cables to the QSFP+ slots.
Connecting the QSFP+ Ports
WARNING: Laser beams will cause eye damage. Do not look into bores of optical modules
or optical bers without eye protection.
1. Insert the RJ45 connector into the RJ45 console port on the front of the switch.
2. Connect the DB9 female connector of the console cable to the serial port on the computer.
Connecting the Console Port
Andere Handbücher für S5860-20SQ
1
Inhaltsverzeichnis
Andere FS Schalten Handbücher
FS
FS Fiberstore S8050-20Q4C Bedienungsanleitung
FS
FS IES5100-24FS Bedienungsanleitung
FS
FS S3700-24T4F Bedienungsanleitung
FS
FS S1900-5T Bedienungsanleitung
FS
FS MANAGED L2 Bedienungsanleitung
FS
FS PoE+ Series Bedienungsanleitung
FS
FS S1900-24T Bedienungsanleitung
FS
FS S3150-8T2FP Bedienungsanleitung
FS
FS NC8400 Series Bedienungsanleitung
FS
FS S3700-24T4F Bedienungsanleitung
FS
FS S3910-24TF Betriebsanleitung
FS
FS S5850-48S8C Bedienungsanleitung
FS
FS S3700-24T4F Bedienungsanleitung
FS
FS S3150-8T2FP Bedienungsanleitung
FS
FS S1150-8T2F Bedienungsanleitung
FS
FS S3200 Series Bedienungsanleitung
FS
FS S3150-8T2FP Bedienungsanleitung
FS
FS S5800-48F4SR Bedienungsanleitung
FS
FS PoE+ Series Bedienungsanleitung
FS
FS S5850-24S2Q Bedienungsanleitung
