FS S5850-24S2C-DC Bedienungsanleitung
SWITCH DE ROUTAGE L3 MANAGEABLE
MANAGED L3 ROUTING SWITCHE
MANAGED L3 ROUTING SWITCH
V1.0
Quick Start Guide
Quick Start Anleitung
Guide de Démarrage Rapide
S5850-24S2C-DC
S5850-24S2C-DC
100G
S5850-24S2C-DC
1 2 345 6 78 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
25 26
100G
40GEBreakout 123 4
ID SYS
CON
ETH
Introduction
S5850-24S2C-DC
Terminal Block Connector x 2
Grounding Cable x1 Rubber Pad x4 M4 Screw x8
Mounting Bracket x2
Console Cable x1 Cat5e Cable x1
Accessories
Thank you for choosing S5850-24S2C-DC Switch. This guide is designed to familiarize you with the
layout of the switch and describes how to deploy the switch in your network.
1
EN
S5850-24S2C-DC
1 2 345 6 78910 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
100G
40GEBreakout 123 4
ID SYS
CON
ETH
1 2 345 6 78910 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
100G
40GEBreakout 123 4
ID SYS
CON
ETH
S5850-24S2C-DC
Hardware Overview
Front Panel Ports
Front Panel LEDs
QSFP28
SFP+
USB
CON
QSFP28
SFP+
ETH 40G Breakout LED
SYS
Ports Description
SFP+
QSFP28
CON
SFP+ ports for 1/10G connection
QSFP28 ports for 40/100G connection
An RJ45 console port for serial management
ETH
USB
An Ethernet management port
A USB management port for software and configuration backup
and offline software upgrade
ID
SYS
ID indication function enable.Blue
Green
Off
Off
Amber
ID indication function disable.
The System is normally running.
The system occurs alarm or error.
No power or no system runs or runs abnormally.
ETH
Green
Blinking Green
Off
Port is linked.
Port is receiving or transmitting packets.
Port is not linked.
LEDs Status Description
ETH
ID
2
EN
+
NULL
-
-48V- -60V,6A
+
NULL
-
-48V- -60V,6A
Back Panel
Grounding Point 3 Fixed Fans
Breakout
Loop Blinking
Off
QSFP28
SFP+
Green
Blinking Green
Blinking Green
Off
Off
Amber
Blinking Amber
Blinking Amber
Green
Amber
LEDs Status
One or more 40/100G ports are breakout.
None of the 40/100G port is breakout.
10G port is linked.
The SFP+ port is transmitting or receiving packets at 10G.
1G port is linked.
The SFP+ port is transmitting or receiving packets at 1G.
Port is not linked.
40/100G port is linked.
The QSFP28 port is transmitting or receiving packets at 40/100G.
10/25G port is linked.
The QSFP28 port is transmitting or receiving packets at 10/25G.
Port is not linked.
Description
2 Hot-swappable Power Supplies
3
EN
Site Environment:
Installation Requirements
Do not operate it in an area that exceeds an ambient temperature of 45°C.
The installation site must be well ventilated.
Ensure that there is adequate air flow around the switch.
Be sure that the switch is level and stable to avoid any hazardous conditions.
Do not install the equipment in a dusty environment.
The installation site must be free from leaking or dripping water, heavy dew, and humidity.
Ensure rack and working platforms are well earthed.
Before you begin the installation, make sure that you have the followings:
Phillips screwdriver.
M6 Screws.
Standard-sized, 19" wide rack with a minimum of 1U height available.
Category 5e or higher RJ-45 Ethernet cables for connecting the network devices.
Mounting the Switch
Desk Mounting
1. Attach four rubber pads to the bottom.
2. Place the chassis on a desk.
4
EN
S5850-24S2C-DC
100G
S5850-24S2Q
1 2 345
ID SYS
CON
ETH
S5850-24S2Q
ID SYS
CON
ETH
Rack Mounting
1. Secure the mounting brackets to the two sides of the switch with eight M4 screws.
2. Attach the switch to the rack using four M6 screws and cage nuts.
5
EN
5 6 78910 11 12 13 14 15 16 17 18 19 20 21 22 23 24
25 26
100G
40GE Breakout 123 4
1 2 345 6 78910 11 12 13 14 15 16 17 18 19 20 21 22 23 24
25 26
40G
40GEBreakout 123 4
100G
S5850-24S2Q
ID SYS
CON
ETH
S5850-24S2Q
ID SYS
CON
ETH
1. Connect one end of the grounding cable to a proper earth ground, such as the rack in which the
switch is mounted.
2. Secure the grounding lug to the grounding point on the switch back panel with the washer and
screws.
Grounding the Switch
CAUTION: The earth connection must not be removed unless all supply connections
have been disconnected.
Connecting the Power
+
NULL
-
-48V- -60V,6A
The front panel of the power supply indicates a DC inlet power socket and consists of one terminal
block connector within 3 contacts. Please follow the steps below to insert the power wire.
1. Insert positive/negative DC power wires into Contacts + and -.
2. Tighten the wire-clamp screws to prevent the wires from loosening.
NO.
1
2
3
Name
+
-
NULL
Description
Positive
Negative
Null
+NULL
-
6
EN
CAUTION: Laser beams will cause eye damage. Do not look into bores of optical modules
or optical fibers without eye protection.
First install SFP+ transceivers and then connect the fiber optic cable to the transceiver ports, or directly
connect DAC cables to the SFP+ slots.
Connecting the SFP+ Ports
First install QSFP28 transceivers and then connect the fiber optic cable to the transceiver ports, or
connect DAC cables to the QSFP28 slots.
Connecting the QSFP28 Ports
1 2 345 6 78910 11 12 13 14 15 16 17 18 19 20 21 22 23 24
25 26
100G
40GE Breakout 123 4
1 2 345 6 78910 11 12 13 14 15 16 17 18 19 20 21 22 23 24
25 26
100G
40GE Breakout 123 4
7
EN
ID SYS
CON
ETH
1 2 345 6 7
ID SYS
CON
ETH
Connecting the Management Ports
1. Insert the RJ45 connector of the console cable into the RJ45 console port on the front of the switch.
2. Connect the other end of the console cable to the RS-232 serial port on the computer.
1. Connect one end of a standard RJ45 Ethernet cable to a computer.
2. Connect the other end of the cable to the ETH port on the front of the switch.
Connecting the Console Port
Connecting the ETH Port
8
EN
S5850-24S2C-DC
S5850-24S2C-DC
1 2 345 6 78910 11 12 13 14 15 16 17 18 19 20 21 22 23 24
25 26
40G
40GE Breakout 123 4
8910 11 12 13 14 15 16 17 18 19 20 21 22 23 24
25 26
40G
40GE Breakout 123 4
1 2 345 6 789
ID SYS
CON
ETH
USB
Configuring the Switch
Insert the Universal Serial Bus (USB) flash disk to the USB port for software and configuration backup
and offline software upgrade.
Step 1: Connect the computer to the Management port of the switch using the network cable.
Step 2: Set the IP address of the computer to 192.168.1.x. ("x" is any number from 2 to 254.). Set the
subnet mask of the computer to 255.255.255.0.
Connecting the USB Port
Configuring the Switch Using the Web-based Interface
?x
OK Cancel
General
IP address:
Subnet mask:
Default gateway:
You can get IP settings assigned automatically if your network
supports this capability. Otherwise, you need to ask your network
administrator for the appropriate IP settings.
Internet Protocol Version 4(TCP/IPv4) Properties
Use the following IP address:
Obtain an IP address automatically
Preferred DNS server:
Alternate DNS server:
Validate settings upon exit Advanced...
. . . 21168192
0255
255255
. . .
. . .
. . .
. . .
Obtain DNS server address automatically
Use the following DNS server addresses:
9
EN
S5850-24S2C-DC
Andere Handbücher für S5850-24S2C-DC
1
Inhaltsverzeichnis
Sprachen:
Andere FS Schalten Handbücher
FS
FS IES3100-8TF-P Bedienungsanleitung
FS
FS S3700-24T4F Bedienungsanleitung
FS
FS S3950-4T12S-R Bedienungsanleitung
FS
FS NC8400 Series Bedienungsanleitung
FS
FS S3150-8T2FP Bedienungsanleitung
FS
FS S3900 Series Bedienungsanleitung
FS
FS S3150-8T2FP Bedienungsanleitung
FS
FS PoE+ Series Bedienungsanleitung
FS
FS S5800 Series Bedienungsanleitung
FS
FS SC9405 Series Bedienungsanleitung
FS
FS S3260-8T2FP Bedienungsanleitung
FS
FS S1900-8TP Bedienungsanleitung
FS
FS S5500-48T8SP Bedienungsanleitung
FS
FS S5860-48SC Betriebsanleitung
FS
FS S3910 Series Bedienungsanleitung
FS
FS S3410 Series Bedienungsanleitung
FS
FS IES5100-24TF Bedienungsanleitung
FS
FS S5860-20SQ Bedienungsanleitung
FS
FS S3700-24T4F Bedienungsanleitung
FS
FS S5900-24S4T2Q Bedienungsanleitung
