Fujitsu Siemens Computers D2300 Bedienungsanleitung

System Board D2300

for RX200 S3

Technical Manual

Edition June 2006

Comments…Suggestions…Corrections…

The User Documentation Department would like to

know your opinion of this manual. Your feedback helps

us optimize our documentation to suit your individual

needs.

Fax forms for sending us your comments are included in

the back of the manual.

There you will also find the addresses of the relevant

User Documentation Department.

Certified documentation

according to DIN EN ISO 9001:2000

To ensure a consistently high quality standard and

user-friendliness, this documentation was created to

meet the regulations of a quality management system

which complies with the requirements of the standard

DIN EN ISO 9001:2000.

cognitas. Gesellschaft für Technik-Dokumentation mbH

www.cognitas.de

Delivery subject to availability; right of technical modifications reserved.

All hardware and software names used are trademarks of their respective manufacturers.

D2300 (RX200 S3) Technical Manual

Contents

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2 Important notes . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.1 Notes on safety . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.2 CE Certificate of Conformity . . . . . . . . . . . . . . . . . . 10

2.3 Environmental protection . . . . . . . . . . . . . . . . . . . . 11

3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.2 Main memory . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3.3 PCI-Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3.3.1 ISA bus resources . . . . . . . . . . . . . . . . . . . . . . . . 20

3.3.2 PCI resources . . . . . . . . . . . . . . . . . . . . . . . . . . 21

3.4 Screen resolution . . . . . . . . . . . . . . . . . . . . . . . . 23

3.5 Temperature / system monitoring . . . . . . . . . . . . . . . . 23

3.6 Interfaces and Connectors . . . . . . . . . . . . . . . . . . . 25

3.6.1 External ports . . . . . . . . . . . . . . . . . . . . . . . . . . 27

3.7 Settings with jumpers . . . . . . . . . . . . . . . . . . . . . . 29

4 Replacing the lithium battery . . . . . . . . . . . . . . . . . 31

Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

D2300 (RX200 S3) Technical Manual 5

1Introduction

This technical manual describes the system board D2300, which is equipped

with one or two Intel® processors.

Further information you will find in the BIOS description.

For additional driver information, refer to the Readme files located on the server

hard disk and on the supplied "Update CDs" or the "ServerStart" CD.

Notational conventions

The meanings of the symbols and fonts used in this manual are as follows:

italics indicates commands, menu options or software

programs.

fixed font indicate system output on the monitor.

semi-bold fixed font indicates values to be entered through the keyboard.

[Key symbol] indicates keys according to their representation on the

keyboard.

If capital letters are to be entered explicitly, then the

Shift key is shown, e.g. [SHIFT] - [A] for A.

If two keys need to be pressed at the same time, then

this is shown by placing a hyphen between the two key

symbols.

"Quotation marks" Indicates names of chapters and terms that are being

emphasized.

ÊDescribes an operation that must be performed.

VCAUTION! Pay particular attention to texts marked with this

symbol. Failure to observe these warnings may

endanger your life, destroy the system or lead to the

loss of data.

IIndicates additional information, notes and tips

Table 1: Notational conventions

D2300 (RX200 S3) Technical Manual 7

2 Important notes

In this chapter you will find essential information regarding safety when working

with your server.

VCAUTION!

With the system board installed you must open the system to access the

system board. How to dismantle and reassemble the system is described

in the service manual accompanying your system.

When installing the system board, refer to the specific installation infor-

mation in the operating and/or service manual for the receiving server.

2.1 Notes on safety

VCAUTION!

●The actions described in these instructions should only be performed

by authorized, qualified personnel. Equipment repairs should only be

performed by qualified staff. Any failure to observe the guidelines in

this manual, and any unauthorized openings and improper repairs

could expose the user to risks (electric shock, fire hazards) and could

also damage the equipment. Please note that any unauthorized

openings of the device will result in the invalidation of the warranty

and exclusion from all liability.

●Transport the device only in the antistatic original packaging or in

packaging that protects it from knocks and jolts.

●Only install expansions that are allowed for the system board. If you

install other expansions, you may damage the requirements and rules

governing safety and electromagnetic compatibility or your system.

Information on which system expansions are approved for installation

can be obtained from our customer service center or your sales

outlet.

●The warranty expires if the device is damaged during the installation

or replacement of system expansions.

8 Technical Manual D2300 (RX200 S3)

Notes on safety Important notes

V●Components can become very hot during operation. Ensure you do

not touch components when making extensions to the system board.

There is a danger of burns!

●Transmisson lines to peripheral devices must be adequately shielded.

●To the LAN wiring the requirements apply in accordance with the

standards EN 50173 and EN 50174-1/2. As minimum requirement

the use of a protected LAN line of category 5 for 10/100 Mbps

Ethernet, and/or of category 5e for Gigabit Ethernet is considered.

The requirements of the specification ISO/IEC 11801 are to be

considered.

●Never connect or disconnect data transmission lines during a storm

(risk of lightning hazard).

Batteries

VCAUTION!

●Incorrect replacement of lithium battery may lead to a risk of

explosion. The batteries may only be replaced with identical batteries

or with a type recommended by the manufacturer.

It is essential to observe the instructions in the chapter “Replacing the

lithium battery”.

D2300 (RX200 S3) Technical Manual 9

Important notes Notes on safety

Modules with electrostatic-sensitive components

Boards with electrostatic sensitive devices (ESD) are marked with the following

label:

Figure 1: ESD label

You must follow the instructions below when handling modules containing

electrostatic-sensitive components

●You must always discharge yourself of static charges (e.g. by touching a

grounded object) before touching the components.

●The equipment and tools you use must be free of static charges.

●Remove the power plug from the power socket before inserting or removing

boards containing ESDs.

●Always hold boards with ESDs by theit edges.

●Do not touch any exposed pins or conductors on a component.

●Use a grounding cable designed for this purpose to connect yourself to the

system unit as you install/deinstall the board.

●Place all components on a static-free surface.

IYou will find a detailed description for handling ESD components in the

relevant European or international standards (EN 61340-5-1,

ANSI/ESD S20.20).

10 Technical Manual D2300 (RX200 S3)

CE Certificate of Conformity Important notes

Notes about boards

●During installation/deinstallation of the system board, observe the specific

instructions described in the service manual for the server.

●Remove the plug from the mains outlet so that system and system board are

totally disconnected from the mains voltage.

●To prevent damage to the system board, the components and conductors on

it, please take great care when you insert or remove boards. Take great care

to ensure that extension boards are slotted in straight, without damaging

components or conductors on the system board, or any other components,

for example EMI spring contacts

●Be careful with the locking mechanisms (catches, centring pins etc.) when

you replace the system board or components on it, for example memory

modules or processors.

●Never use sharp objects (screwdrivers) for leverage.

2.2 CE Certificate of Conformity

The shipped version of this board complies with the requirements

of the EEC directive 89/336/EEC "Electromagnetic compatibility".

Compliance was tested in a typical PRIMERGY configuration.

Inhaltsverzeichnis

Andere Fujitsu Siemens Computers Hauptplatine Handbücher

Fujitsu Siemens Computers

Fujitsu Siemens Computers D2352 Bedienungsanleitung

Fujitsu Siemens Computers

Fujitsu Siemens Computers D1961 Bedienungsanleitung

Fujitsu Siemens Computers

Fujitsu Siemens Computers D2470 Bedienungsanleitung

Fujitsu Siemens Computers

Fujitsu Siemens Computers D1562 Bedienungsanleitung

Fujitsu Siemens Computers

Fujitsu Siemens Computers D1409 Bedienungsanleitung

Fujitsu Siemens Computers

Fujitsu Siemens Computers D1332 Bedienungsanleitung

Fujitsu Siemens Computers

Fujitsu Siemens Computers D1837 Bedienungsanleitung

Fujitsu Siemens Computers

Fujitsu Siemens Computers D1218 Bedienungsanleitung

Fujitsu Siemens Computers

Fujitsu Siemens Computers D1875 Bedienungsanleitung

Fujitsu Siemens Computers

Fujitsu Siemens Computers D1501 Bedienungsanleitung

Fujitsu Siemens Computers

Fujitsu Siemens Computers D2164 Bedienungsanleitung

Fujitsu Siemens Computers

Fujitsu Siemens Computers D2721 Bedienungsanleitung

Fujitsu Siemens Computers

Fujitsu Siemens Computers D1451 Bedienungsanleitung

Fujitsu Siemens Computers

Fujitsu Siemens Computers D2438 Bedienungsanleitung

Fujitsu Siemens Computers

Fujitsu Siemens Computers D1132 Bedienungsanleitung

Fujitsu Siemens Computers

Fujitsu Siemens Computers D1381 Bedienungsanleitung

Fujitsu Siemens Computers

Fujitsu Siemens Computers D1931 Bedienungsanleitung

Fujitsu Siemens Computers

Fujitsu Siemens Computers D1421 Bedienungsanleitung

Fujitsu Siemens Computers

Fujitsu Siemens Computers D1534 Bedienungsanleitung

Fujitsu Siemens Computers

Fujitsu Siemens Computers D1644 Bedienungsanleitung

Fujitsu Siemens Computers

Fujitsu Siemens Computers D1332 Bedienungsanleitung

Fujitsu Siemens Computers

Fujitsu Siemens Computers D2130 Bedienungsanleitung

Fujitsu Siemens Computers

Fujitsu Siemens Computers D1555 Bedienungsanleitung

Fujitsu Siemens Computers

Fujitsu Siemens Computers D1740 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung