Fujitsu PSN 900 Plus Bedienungsanleitung
0
PSN 900 Plus Palm Vein Identification
Device (PVID) Operating Manual
Version：1.0.0
Copyright belongs to Jiangsu Fujitsu Telecommunications Technology Co., Ltd.
Copyright reserved, can t change, copy or print without permission, offenders must
be investigated.
1
C o n t e n t s
Chapter1 Specifications ........................................................................ 2
Chapter2 Structure Diagram ................................................................. 3
Chapter3 How to Put Hand ................................................................... 4
Chapter4 Operating Instructions ........................................................... 8
Chapter5 Output Protocol ................................................................... 33
Chapter6 Trobuleshooting .................................................................. 34
2
C apter1 Specifications
PSN 900 Plus PVID Specifications and Parameters Table:
No. Item Specifications
1 Dimension(L)*(W)*(H) mm 302mm*132mm*38mm
2 Material ABS
3 Colour Black
4 Weight Less than 2kg
5 Touch screen 5.0 inches (resolution: 800 * 480)
6 Types of supported RF cards Mifare S50/S70/Desfire, ID / HID(optional)
7 Memory Capacity 4GB
8 Speaker 1*1W
9 USB2.0 Interface 1
10 Communication Interface
Electric lock / Exit Button/ Alarm
Wiegand 26/34,Corporate 1000,CSN32 (connected with access
controller, Max 50m)
LAN（10/100M）
11 Power DC: 12V/1.5A (DC 12V±5%)
12 Operating
Environment
Temperature
Humidity
0℃ ~ 50℃; relative humidity: 30 ~80%, No condensation
Note: T e product is only suitable for indoor installation
Lighting
Environment
Enrollment
Authentication
Natural light (sunlight)
<2000Lux <3000Lux
Fluorescent lamp light <2000Lux <3000Lux
halogen light
<500Lux <700Lux
13 Work Mode
Palm Vein (1:N) Note: These three
modes support
separate card swiping.
PIN Code+Palm Vein (1:1)
Group + Palm Vein (1:G)
Card + Palm Vein (1:1)
14 False Reject Rate (FRR) <0.01% Note:According to ISO/IEC19795 algorithm
False Accept Rate (FAR) <0.00001%Note:According to ISO/IEC19795 algorithm
15 User Capacity
Max users 1000 IDs (1:N Mode)
40,000 IDs (1:1 Mode, extensible)
>500 IDs 1:1 Mode (recommended)
<500 IDs 1:N Mode (recommended)
16 Authentication
Speed
1: N Mode <2.5s (<500IDs)
1: 1 Mode <1s
17 Event Log Records in the last 6 months
3
C apter2 Structure Diagram
PSN 900 Plus PVID structure diagram:
4
C apter3 How to Put Hand
Diagram of putting hand：
5
6
7
Note：
：：
：
1. Recognition accuracy rate is affected by enrolled palm vein templates.
If t e enrolled template is not precise enoug (incorrect and position
or and bent), even put ands in correct way w en verifying, it would
misjudge.
Be sure to use t e black palm guide for enrollment.
2. In particular, if it is not prompted to remove t e and, please make
sure not to remove t e wrist from t e Wrist-support during t e
enrollment process.
3. W en using t e transparent circle to do identification or verification:
Since t ere is no palm guide, except put ands accordance wit t e
specification requirements strictly, to keep t e distance from t e palm
to t e sensor s ould be 40 ~ 60mm; if it prompts to adjust t e palm
location repeatedly, t is means t at you did not mastered skills to put
ands yet, please replace t e circle wit a palm guide..
4. In t e following cases, your enrolled palm vein templates may be
incorrect, aut entication errors(false reject) may repeated occur:
1) Hand wrapped wit bandage.
2) Hands are unclean, wet or injured.
5. Please keep t e sensor surface clean. If dirty, just wipe it gently wit
dry and soft clean clot ; don’t clean t e sensor surface by water or
organic solvents.
6. Recommend installing t e product indoors, cannot be exposed to direct
sunlig t.
8
C apter4 Operating Instructions
Step 1: Plug in the connection terminals of the power adapter. Turn on the
power supply.The Palm Vein Identification Device boots up and the following
screen appears:
After the boot-up is completed, the idle screen appears.
Step 2: Click the touch screen and then the Management button to enter the
following screen. If no system user is registered as an administrator, it will prompt
that an administrator should be registered duly.
Note: A maximum of 10 administrators can be registered.
9
Then enter the main menu screen as follows:
Step 3: Click "Manage" to enter the system settings screen. Click "Work mode"
to enter the screen for selecting a work mode – Palm Vein, Card + Palm Vein, PIN
Code + Palm Vein, or Group No. + Palm Vein mode. Select the work mode to be
used, and then you can register an administrator or user.
1. Palm Vein
2. Card + Palm Vein (recommended)
3. PIN Code + Palm Vein
4. Group No. + Palm Vein
Step 4: After the work mode is selected, click the Back button to enter the
Main Menu screen. Click "User" and "Enroll" in sequence to enter the following user
Inhaltsverzeichnis
Andere Fujitsu IP-Zugriffskontrollsysteme Handbücher
