Fujitsu CW35 Series Bedienungsanleitung

CW35 Series

Rev. C+

System Board

Users Manual

401D0948

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior

written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any

express or implied warranties of merchantability or fitness for any

particular purpose.The user will assume the entire risk of the use or

the results of the use of this document. Further, the manufacturer

reserves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or

entity of such revisions or changes.

Trademarks

Microsoft®MS-DOS®, WindowsTM, Windows®95 and Windows®98

are registered trademarks of Microsoft Corporation. Intel®and

CeleronTM are registered trademarks of Intel Corporation. Award is

a registered trademark of Award Software, Inc. Other trademarks

and registered trademarks of products appearing in this manual are

the properties of their respective holders.

Caution:

Danger of explosion if battery incorrectly replaced.

Replace only with the same or equivalent type recommended by the

manufacturer.

Dispose of used batteries according to the battery manufacturers

instructions.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and the receiver.

 Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

 Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Table of Contents

Chapter 1 - Introduction

1.1 Features and Specifications..................................................................................

1.2 Package Checklist.........................................................................................................

Chapter 2 - Hardware Installation

2.1 System Board Layout .............................................................................................

2.2 System Memory.............................................................................................................

2.3 Jumper Settings for Clearing CMOS Data..........................................

2.4 Jumper Settings for Wake-On-Keyboard/Mouse....................................

2.5 Jumper Settings for the Audio Codec......................................................

2.6 Jumper Settings for the Systems Beep Message...........................

2.7 Jumper Settings for the CPUs Front Side Bus................................

2.8 Jumper Settings for the Boot Block Lock/Unlock..........................

2.9 Ports and Connectors.............................................................................................

Chapter 3 - Award BIOS Setup Utility

3.1 The Basic Input/Output System.....................................................................

3.1.1 Standard CMOS Features.............................................................

3.1.2 Advanced BIOS Features..............................................................

3.1.3 Advanced Chipset Features ......................................................

3.1.4 Integrated Peripherals.........................................................................

3.1.5 Power Management Setup............................................................

3.1.6 PnP/PCI Configurations....................................................................

3.1.7 System Health Monitor.....................................................................

3.1.8 CPU Frequency Control..................................................................

3.1.9 Load Fail-Safe Defaults.....................................................................

3.1.10 Load Optimized Defaults..............................................................

3.1.11 Set Supervisor Password...............................................................

3.1.12 Set User Password..............................................................................

3.1.13 Save & Exit Setup.................................................................................

3.1.14 Exit Without Saving..............................................................................

Chapter 4 - Supported Softwares

4.1 Desktop Management Interface.....................................................................

4.2 Hardware Doctor Utility........................................................................................

4.3 INF Update for Windows95/98...............................................................

4.4 Installing the Graphics Driver..............................................................................

4.5 Installing the Sound Driver....................................................................................

4.6 Drivers and Utilities Installation Notes.....................................................

Appendix A - Using the Suspend to RAM

Function

A.1 Using the Suspend to RAM Function........................................................

Appendix B - System Error Messages

B.1 POST Beep.......................................................................................................................

B.2 Error Messages..............................................................................................................

Appendix C - Troubleshooting

C.1 Troubleshooting Checklist....................................................................................

Introduction

1.1 Features and Specifications

1.1.1 Features

Chipset

 Intel®810-E (CW35-E)

Intel®810 DC-100 (CW35-D)

Intel®810 (CW35-S)

Intel®810-L (CW35-L)

Processor

The system board is equipped with Socket 370 for installing an Intel

CeleronTM processor that is packaged in PPGA (Plastic Pin Grid

Array). It is also equipped with a switching voltage regulator that

automatically detects 1.30V to 2.05V.

 Future Pentium®III FCPGA 133MHz FSB processor (CW35-E)

 Future Pentium®III FCPGA 100MHz FSB processor

 CeleronTM PPGA (300A-533MHz) 66MHz FSB processor

System Memory

 16MB to 256MB/512MB memory using unbuffered DIMMs with

64Mbit/128Mbit technology. (You must use 32MBx64 SDRAM

DIMM to support 512MB memory.)

 Two 168-pin DIMM sockets

 Uses x64 PC-100 SDRAM DIMM, 3.3V

Chapter 1 - Introduction

DIMMs

2MBx64

4MBx64

8MBx64

16MBx64

32MBx64

Memory Size

16MB

32MB

64MB

128MB

256MB

Introduction

Expansion Slots

The system board is equipped with 3 dedicated PCI slots and 1

AMR slot. AMR (Audio/Modem Riser) is an interface desgined for

installing an audio riser card, modem riser card or audio/modem riser

card that is compliant to the AMR specification.

Onboard Graphics Features

 Graphics memory

- Shares 1MB of the system memory. This is fixed regardless of

the size of the system memory.

- Uses the Dynamic Video Memory Technology (DVMT) tech-

nology. This freely changes in size because graphics memory is

allocated from the system memory according to current

needs.

- 4MB onboard display cache (CW35-E and CW35-D only)

 Graphics controller

- 100MHz (CW35-D) or 133MHz (CW35-E) super AGP

performance using 4MB display cache memory

- 3D hyper pipelined architecture

- 2D hardware and motion video acceleration

- 9-bit precision hardware motion compensation assistance for

software MPEG2 decode

- Software DVD at 30fps

 2D graphics features

- Resolution: up to 1600x1200 in 8-bit color at 85Hz refresh

- 64-bit blitter with enhancements

- 64x64x3 color transparent cursor

- Arithmetic stretch blitter

 3D graphics features

- 600K-700K tri/sec sustained

- 55Mpixels/sec

- Flat and Gouraud shading

- MIP mapping with bi-linear and anisotropic filtering

- 16-bit color/Z-buffering

- Discrete/strips/fans

- Anisotropic filtering

- Texture compositing, color keying and chroma keying

 Software drivers

- Windows®95/98

- Windows NT®4.0

Introduction

Onboard Audio Features

 Supports Microsoft®DirectSound

 32-voice wavetable synthesis

 AC97 supported with full duplex, independent sample rate con-

verter for audio recording and playback

 Downloadable sound (DLS) level-1

Compatibility

 Microsoft PC 98 compliant

 VESA Display Power Management Signaling (DPMS)

 VESA DDC2B for Plug and Play monitors

 PCI 2.2, AMR 1.0 and AC 97 compliant

ATX Double Deck Ports (PC 99 color-coded connectors)

 Two USB ports

 One NS16C550A-compatible DB-9 serial port

 One DB-15 VGA port

 One SPP/ECP/EPP DB-25 parallel port

 One mini-DIN-6 PS/2 mouse port

 One mini-DIN-6 PS/2 keyboard port

 One game/MIDI port

 Three audio jacks: line-out, line-in and mic-in

Connectors

 One 9-pin connector for external serial port

 One connector for IrDA interface

 Two IDE connectors

 One floppy drive interface supports up to two 2.88MB floppy

drives

 One 20-pin ATX power supply connector

 One Wake-On-LAN connector

 CPU, chassis and second chassis fan connectors

 One opened chassis alarm connector

 Three CD audio-in connectors (2 Sony and 1 Mitsumi)

 One TAD connector for telephony audio devices

Introduction

PCI Bus Master IDE Controller

 Two PCI IDE interfaces support up to four IDE devices

 Supports Ultra ATA/33 (CW35-L) or ATA/66 (CW35-E,

CW35-D or CW35-S) hard drives

 PIO Mode 4 Enhanced IDE (data transfer rate up to 14MB/sec.)

 Bus mastering reduces CPU utilization during disk transfer

 Supports ATAPI CD-ROM, LS-120 and ZIP

IrDA Interface

The system board is equipped with an IrDA connector for wireless

connectivity between your computer and peripheral devices. It

supports peripheral devices that meet the IrDA or ASKIR standard.

USB Ports

The system board is equipped with two USB ports. USB allows

data exchange between your computer and a wide range of

simultaneously accessible external Plug and Play peripherals.

BIOS

 Award BIOS, Windows®95/98 Plug and Play compatible

 Supports SCSI sequential boot-up

 Flash EPROM for easy BIOS upgrades (4Mbit)

 Includes NCR 810 SCSI BIOS

 Supports DMI 2.0 function

Desktop Management Interface (DMI)

The system board comes with a DMI 2.0 built into the BIOS. The

DMI utility in the BIOS automatically records various information

about your system configuration and stores these information in the

DMI pool, which is a part of the system board's Plug and Play

BIOS. DMI, along with the appropriately networked software, is

designed to make inventory, maintenance and troubleshooting of

computer systems easier. Refer to chapter 4 for instructions on using

the DMI utility.

Introduction

1.1.2 System Health Monitor Functions

The system board is capable of monitoring the following system

health conditions.

 Monitors processor/system temperature and overheat alarm

 One optional temperature sensor for user customization

 Monitors 5VSB/VBAT/1.5V/3.3V/+5V/±12V/processor voltages

and failure alarm

 Monitors the fan speed of the processor fan, chassis fan and

second chassis fan; controls the fan speed of the processor and

chassis fans; and failure alarm

 Automatic fan on/off control

 Read back capability that displays temperature, voltage and fan

speed

 Opened chassis alarm

 Supports CeleronTM processor thermal diode output (real proces-

sor temperature)

Refer to the System Health Monitor section in chapter 3 and the

Hardware Doctor Utility section in chapter 4 for more information.

1.1.3 Intelligence

Automatic CPU/Chassis Fan Off

The CPU and chassis fans will automatically turn off once the system

enters the Suspend mode.

Dual Function Power Button

Depending on the setting in the Soft-Off By PWR-BTTN field of

the Power Management Setup, this switch will allow the system to

enter the Soft-Off or Suspend mode.

External Modem Ring-on

The Modem Ring-on feature allows the system that is in the

Suspend mode or Soft Power Off mode to wake-up/power-on to

respond to incoming calls.

Dieses Handbuch passt für folgende Modelle

Andere Fujitsu Hauptplatine Handbücher

Fujitsu

Fujitsu D3144 Bedienungsanleitung

Fujitsu

Fujitsu D3231-S Bedienungsanleitung

Fujitsu

Fujitsu D2619-N Bedienungsanleitung

Fujitsu

Fujitsu AD11 Bedienungsanleitung

Fujitsu

Fujitsu D3071-S Bedienungsanleitung

Fujitsu

Fujitsu F-Cue Bedienungsanleitung

Fujitsu

Fujitsu SK-91F467D-208PFV Bedienungsanleitung

Fujitsu

Fujitsu D2179 Bedienungsanleitung

Fujitsu

Fujitsu D2610 Bedienungsanleitung

Fujitsu

Fujitsu D3011 Bedienungsanleitung

Fujitsu

Fujitsu F2MC-16FX QFP-100P Bedienungsanleitung

Fujitsu

Fujitsu D2759 Bedienungsanleitung

Fujitsu

Fujitsu FLASH-CAN-64P-350-PMC Bedienungsanleitung

Fujitsu

Fujitsu GA-8ISXT-FS P4 Titan Bedienungsanleitung

Fujitsu

Fujitsu D2799 Bedienungsanleitung

Fujitsu

Fujitsu SK-91464A-100PMC Bedienungsanleitung

Fujitsu

Fujitsu D2119 Bedienungsanleitung

Fujitsu

Fujitsu D3071 Bedienungsanleitung

Fujitsu

Fujitsu GA-8SGXP-FS P4 Titan Series Bedienungsanleitung

Fujitsu

Fujitsu SK-AMAPOLLO-BASE-V11 Bedienungsanleitung

Fujitsu

Fujitsu D1031 Bedienungsanleitung

Fujitsu

Fujitsu D2542 Bedienungsanleitung

Fujitsu

Fujitsu MB96300 series Bedienungsanleitung

Fujitsu

Fujitsu D3003-S Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung