Fujitsu D3313-S Bedienungsanleitung
Assembly Instructions D3313-S
__________________________________________________________________________________________________________________________________________________________
Page 1 of 15 www.fujitsu.com
Assembly Instructions
for D3313-S Kit Solution
________________________________________________________________________________________________________________
Table of Contents
Step 1 Prepare the Chassis .............................................................................................................................................2
Step 2 Mount the Cooler.................................................................................................................................................4
Step 3 Insert RAM...........................................................................................................................................................5
Step 4 Put Board in Chassis ............................................................................................................................................5
Step 5 Wire HDD.............................................................................................................................................................7
Step 6 Mount HDD..........................................................................................................................................................8
Step 7 Add Cross Bar.....................................................................................................................................................10
Step 8 Close Chassis......................................................................................................................................................11
Optional: Application of a Passive Riser Card + Graphic Card AMD W2100 ...................................................................12
Step 9 Mount mSata.....................................................................................................................................................12
Step 10 Insert Passive Riser Card ..................................................................................................................................13
Step 11 Add Graphic Card AMD W2100........................................................................................................................13
Assembly Instructions D3313-S
__________________________________________________________________________________________________________________________________________________________
Page 2 of 15 www.fujitsu.com
Step 1 Prepare the Chassis
Open the chassis with two hands by putting some pressure on your thumbs to push the cover forward.
After opening the chassis take out the contents.
Assembly Instructions D3313-S
__________________________________________________________________________________________________________________________________________________________
Page 3 of 15 www.fujitsu.com
Then, remove the cross bar (middle section) of the chassis.
Remove the screw to take out the HDD tray. After removing the screw slide the tray off the chassis.
You should now have
a completely empty
chassis.
Assembly Instructions D3313-S
__________________________________________________________________________________________________________________________________________________________
Page 4 of 15 www.fujitsu.com
Step 2 Mount the Cooler
Place the backplate underneath the board, pushing the studs on the backplate through the holes on the board
around the CPU.
Then put the cooler on top of the CPU and screw it onto the backplate through the board. The thermal paste is
already applied.
Now plug in the cooler.
Assembly Instructions D3313-S
__________________________________________________________________________________________________________________________________________________________
Page 5 of 15 www.fujitsu.com
Step 3 Insert RAM
If you only have one RAM attach it to the top slot, if you have two, start with the bottom slot.
Put in the first RAM tilted slightly upwards. Then push it down.
Now put in the second RAM in the same manner, putting it in tilted upwards and then pushing it down.
Step 4 Put Board in Chassis
Start by putting all the connectors on the board through the designated holes in the chassis.
Assembly Instructions D3313-S
__________________________________________________________________________________________________________________________________________________________
Page 6 of 15 www.fujitsu.com
Now push down the board so that the holes on the board fit onto the screw holes on the chassis.
Now screw in the board in all four holes. The board should now look like this:
Assembly Instructions D3313-S
__________________________________________________________________________________________________________________________________________________________
Page 7 of 15 www.fujitsu.com
Step 5 Wire HDD
At first you need to attach the HDD to the tray you have taken out earlier.
Align the screw holes with the holes on the tray.
Now add screws from the bottom.
Assembly Instructions D3313-S
__________________________________________________________________________________________________________________________________________________________
Page 8 of 15 www.fujitsu.com
Step 6 Mount HDD
To mount the HDD place the hooks of the tray on the designated hole in the chassis and push the tray forward.
You can now connect the HDD tray to the board.
Then screw the HDD onto the chassis.
Assembly Instructions D3313-S
__________________________________________________________________________________________________________________________________________________________
Page 9 of 15 www.fujitsu.com
Now plug in the power cable.
Connect the SATA cable.
Assembly Instructions D3313-S
__________________________________________________________________________________________________________________________________________________________
Page 10 of 15 www.fujitsu.com
Step 7 Add Cross Bar
At first, plug in the front panel cable coming from the
cross bar.
Next, plug in the intrusion cable. On the left of the picture below you can see the plugged in front panel cable.
Then, set the cross bar in its
designated spot on the chassis
Inhaltsverzeichnis
Andere Fujitsu Hauptplatine Handbücher
Fujitsu
Fujitsu D3031 Bedienungsanleitung
Fujitsu
Fujitsu D3144 Bedienungsanleitung
Fujitsu
Fujitsu D3162-B Bedienungsanleitung
Fujitsu
Fujitsu GA-8I848PM P4 Titan Series Bedienungsanleitung
Fujitsu
Fujitsu D3173 Bedienungsanleitung
Fujitsu
Fujitsu P4 Titan-DDR GA-8STXC Bedienungsanleitung
Fujitsu
Fujitsu D2671 Bedienungsanleitung
Fujitsu
Fujitsu GA-8SGXP-FS P4 Titan Series Bedienungsanleitung
Fujitsu
Fujitsu D2530 Bedienungsanleitung
Fujitsu
Fujitsu D3231-S Bedienungsanleitung
Fujitsu
Fujitsu DVB-S Bedienungsanleitung
Fujitsu
Fujitsu MB91470 SERIES Bedienungsanleitung
Fujitsu
Fujitsu D3003 Bedienungsanleitung
Fujitsu
Fujitsu D2109 Bedienungsanleitung
Fujitsu
Fujitsu D3664 Bedienungsanleitung
Fujitsu
Fujitsu F2MC-16FX Series Bedienungsanleitung
Fujitsu
Fujitsu D2778 Stücklistenhandbuch
Fujitsu
Fujitsu D3071-S Bedienungsanleitung
Fujitsu
Fujitsu MB96300 series Bedienungsanleitung
Fujitsu
Fujitsu D1837 Bedienungsanleitung
Beliebte Hauptplatine Handbücher anderer Marken
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Bedienungsanleitung
Gigabyte
Gigabyte GA-9IVDT Bedienungsanleitung
Texas Instruments
Texas Instruments ADS8372EVM Bedienungsanleitung
Commell
Commell MS-C73 Bedienungsanleitung
IBT Technologies
IBT Technologies MB860 Bedienungsanleitung
Nvidia
Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung
