Fujitsu GA-8STXC P4 Titan-DDR Bedienungsanleitung

USER’S MANUAL

GA-8STXC

P4 Titan-DDR Motherboard

Pentium®4 Processor Motherboard

Rev. 1001

12ME-8STXC-1001

- 2 - WARNING!

English

Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. To

protect them against damage from static electricity, you should follow some precautions whenever you

work on your computer.

1. Unplug your computer when working on the inside.

2. Use a grounded wrist strap before handling computer components. If you do not have one,

touch both of your hands to a safely grounded object or to a metal object, such as the power

supply case.

3. Hold components by the edges and try not touch the IC chips, leads or connectors, or other

components.

4. Place components on a grounded antistatic pad or on the bag that came with the components

whenever the components are separated from the system.

5. Ensure that theATX power supply is switched off before you plug in or remove the ATX power

connector on the motherboard.

If the motherboard has mounting holes, but they don’t line up with the holes on the base and there

are no slots to attach the spacers, do not become alarmed you can still attach the spacers to the

mounting holes. Just cut the bottom portion of the spacers (the spacer may be a little hard to cut off, so

be careful of your hands). In this way you can still attach the motherboard to the base without worrying

about short circuits. Sometimes you may need to use the plastic springs to isolate the screw from the

motherboard PCB surface, because the circuit wire may be near by the hole. Be careful, don’t let the

screw contact any printed circuit write or parts on the PCB that are near the fixing hole, otherwise it

may damage the board or cause board malfunctioning.

Installing the motherboard to the chassis…

WARNING!

- 3 -GA-8STXC Motherboard

English

Chapter 1 Introduction

to be continued......

Features Summary

Form Factor y30.6cm x 24.4cm ATX size form factor, 4 layers PCB

CPU ySocket 478 for Intel®Micro FC-PGA2 Pentium®4 processor

y Support Intel ®Pentium ®4 (Northwood, 0.13 m) processor

yIntel Pentium®4 400/533MHz FSB

y2nd cache depends on CPU

Chipset ySiS 645DX Host/Memory controller

ySiS 962L MuTIOL Media I/O

Memory y3 184-pin DDR DIMM sockets

ySupports DDR333/DDR266/DDR200 DIMM

ySupports Up to 2 un-buffer double-sided DIMM DDR333 or up to

3 un-buffer Double-sided DIMM DDR266/200

ySupports up to 3GB DRAM (Max)(DDR266/200)

ySupports only 2.5V DDR DIMM

ySupports 64bit ECC type DRAM integrity mode

I/O Control yIT8705

Slots y1 CNR (Communication and Networking Riser) Slot

y1 Universal AGP slot (1X/2X/4X) device support

y5 PCI slot supports 33MHz & PCI 2.2 compliant

On-Board IDE y2 IDE bus master (Dual UDMA33/ATA66/ATA100/ATA133) IDE

ports for up to 4 ATAPI devices

ySupports PIO mode 3,4 (UDMA 33/ATA66/ATA100/ATA133) IDE

& ATAPICD-ROM

On-Board Peripherals y1 Floppy port supports 2 FDD with 360K, 720K, 1.2M, 1.44M

and 2.88M bytes

y1 Parallel port supports Normal/EPP/ECP mode

y2 Serial ports (COMA & COMB)

y6 x USB 2.0/1.1 (2 x Rear,4 x Front by cable)

y1 IrDA connector for IR

y1 FrontAudio connector

Introduction

English

- 4 -

Please set the CPU host frequency in accordance with your processor’s specifications.

We don’t recommend you to set the system bus frequency over the CPU’s specification

because these specific bus frequencies are not the standard specifications for CPU, chipset

and most of the peripherals. Whether your system can run under these specific bus frequen-

cies properly will depend on your hardware configurations, including CPU, Chipsets,

SDRAM, Cards…etc.

Hardware Monitor yCPU/System/Power Fan Revolution detect

yCPU Temperature Detect

ySystem Voltage Detect

On-Board Sound yRealtek ALC650 CODEC

yLine Out / 2 front speaker

yLine In / 2 rear speaker (by s/w switch)

yMic In / center & woofer (by s/w switch)

ySPDIF out

yLine In / Line Out / Mic In / CD In / Game Port

On-Board LAN yBuilt in RTL8100BL Chipset

PS/2 Connector yPS/2 Keyboard interface and PS/2 Mouse interface

BIOS yLicensed AWARD BIOS, 2M bit Flash ROM

ySupports Q-Flash

Additional Features yPS/2 Keyboard power on by password

yPS/2 Mouse power on

ySTR (Suspend-To-RAM)

yWake on LAN (WOL)

yWake on Ring (WOR)

- 5 -GA-8STXC Motherboard

English

GA-8STXC Motherboard Layout

KB_MS

COMA

LPT

LINE_IN

LINE_OUT

MIC_IN USB

LAN

COMB

GAME

CD_IN

ATX_12V

ATX POWER

RTL8100BL

F_AUDIO_I

AC97

SPDIF

SUR_CEN

PWR_FAN

NB_FAN

SiS 645DX

AGP

CNR

I R WOR WOL

F_USB2 F_USB1

SYS_FAN

S_IRQ

IT8705

Main BIOS

F_PANEL

SiS 962L

BUZZER

BAT

IDE2

GA-8STXC

IDE1 FDD

83518

CLR_CMOS

CPU_FAN

DIMM_LED

DDR1

DDR2

DDR3

PC1

PC2

PC3

PC4

PC5

SOCKET 478

- 6 - Hardware Installation Process

English

To set up your computer, you must complete the following steps:

Step 1- Install the Central Processing Unit (CPU)

Step 2- Install memory modules

Step 3- Install expansion cards

Step 4- Connect ribbon cables, cabinet wires and power supply

Step 5- Setup BIOS software

Step 6- Install supporting software tools

Chapter 2 Hardware Installation Process

Step 4

Step 3

Step 4

Step 2

Step 1

- 7 -GA-8STXC Motherboard

English

Step 1: Install the Central Processing Unit (CPU)

Step1-1 : CPU Installation

Pin1 indicator Pin1 indicator

CPU Top View CPU Bottom View

Socket Actuation Lever

1. Pull up the CPU socket lever and

up to 90-degree angle.

Pin1 indicator

2. Locate Pin 1 in the socket and look

for a (golden) cut edge on the CPU

upper corner. Then insert the CPU

into the socket.

3. Press down the CPU socket lever

and finish CPU installation.



Please make sure the CPU type is supported by the motherboard.



If you do not match the CPU socket Pin 1 and CPU cut edge well, it will cause

improper installation. Please change the insert orientation.

- 8 - Hardware Installation Process

English

Step1-2 : CPU Heat Sink Installation

1. Hook one end of the cooler bracket

to the CPU socket first.

2. Hook the other end of the cooler

bracket to the CPU socket.



Please use Intel approved cooling fan.



We recommend you to apply the thermal tape to provide better heat

conduction between your CPU and heatsink.

(The CPU cooling fan might stick to the CPU due to the hardening of the

thermal paste. During this condition if you try to remove the cooling fan, you

might pull the processor out of the CPU socket alone with the cooling fan,

and might damage the processor. To avoid this from happening, we suggest

you to either use thermal tape instead of thermal paste, or remove the cooling

fan with extreme caution.)



Make sure the CPU fan power cable is plugged in to the CPU fan connector,

this completes the installation.



Please refer to CPU heat sink user’s manual for more detail installation

procedure.

- 9 -GA-8STXC Motherboard

English

Step 2: Install memory modules

The motherboard has 3 dual inline memory module (DIMM) sockets. The BIOS will automatically

detects memory type and size. To install the memory module, just push it vertically into the DIMM

socket. The DIMM module can only fit in one direction due to the notch. Memory size can vary

between sockets.

Support Unbuffered DDR DIMM Sizes type:

64 Mbit (2Mx8x4 banks) 64 Mbit (1Mx16x4 banks) 128 Mbit(4Mx8x4 banks)

128 Mbit(2Mx16x4 banks) 256 Mbit(8Mx8x4 banks) 256 Mbit(4Mx16x4 banks)

512 Mbit(16Mx8x4 banks) 512 Mbit(8Mx16x4 banks)

Note:

1. GA-8STXC can only support 4 banks of DDR333.

2. If you mix DDR266 and DDR333 then all modules will run as DDR266.

SS: Single Side, DS: Double Side

Install memory in any combination table:

DDR1 (Bank 0&1) DDR2 (Bank 2&3) DDR3 (Bank 4&5)

S S none none

DS none none

S S S S none

DS S S none

DS DS none

SS SS SS

DS SS SS

DS DS SS

DS DS DS

- 10 - Hardware Installation Process

English

Established on the existing SDRAM industry infrastructure, DDR (Double Data Rate) memory is

a high performance and cost-effective solution that allows easy adoption for memory vendors, OEMs

and system integrators.

DDR memory is a sensible evolutionary solution for the PC industry that builds on the existing

SDRAM infrastructure, yet makes awesome advances in solving the system performance bottleneck

by doubling the memory bandwidth. DDR SDRAM will offer a superior solution and migration path from

existing SDRAM designs due to its availability, pricing and overall market support. PC2100 DDR

memory (DDR266) doubles the data rate through reading and writing at both the rising and falling edge

of the clock, achieving data bandwidth 2X greater than PC133 when running with the same DRAM

clock frequency. With peak bandwidth of 2.1GB per second, DDR memory enables system OEMs to

build high performance and low latency DRAM subsystems that are suitable for servers, workstations,

high-end PC's and value desktop SMA systems. With a core voltage of only 2.5 Volts compared to

conventional SDRAM's 3.3 volts, DDR memory is a compelling solution for small form factor desktops

and notebook applications.

DDR Introduction



When STR/DIMM LED is ON, do not install/remove DIMM from socket.



Please note that the DIMM module can only fit in one direction due to the one

notches. Wrong orientation will cause improper installation. Please change

the insert orientation.

DDR

1. The DIMM socket has a notch, so the DIMM memory

module can only fit in one direction.

2. Insert the DIMM memory module vertically into the

DIMM socket. Then push it down.

3. Close the plastic clip at both edges of the DIMM

sockets to lock the DIMM module.

Reverse the installation steps when you wish to

remove the DIMM module.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Fujitsu Hauptplatine Handbücher

Fujitsu

Fujitsu D2861 Bedienungsanleitung

Fujitsu

Fujitsu D3003 Bedienungsanleitung

Fujitsu

Fujitsu D1170 Bedienungsanleitung

Fujitsu

Fujitsu D2317 Bedienungsanleitung

Fujitsu

Fujitsu GA-8I848PM P4 Titan Series Bedienungsanleitung

Fujitsu

Fujitsu D3654 Series Bedienungsanleitung

Fujitsu

Fujitsu D2420 Bedienungsanleitung

Fujitsu

Fujitsu D3231-S Bedienungsanleitung

Fujitsu

Fujitsu DD2963-S Bedienungsanleitung

Fujitsu

Fujitsu SK-96380-120PMT Bedienungsanleitung

Fujitsu

Fujitsu D3031 Bedienungsanleitung

Fujitsu

Fujitsu F2MC-16FX Series Bedienungsanleitung

Fujitsu

Fujitsu GA-8SGXP-FS P4 Titan Series Bedienungsanleitung

Fujitsu

Fujitsu D3171 Betriebsanleitung

Fujitsu

Fujitsu PTM900 Bedienungsanleitung

Fujitsu

Fujitsu D2529 Bedienungsanleitung

Fujitsu

Fujitsu MB91360 SERIES Bedienungsanleitung

Fujitsu

Fujitsu SK-91460T-144PMC-GPIO Bedienungsanleitung

Fujitsu

Fujitsu D1826-G Bedienungsanleitung

Fujitsu

Fujitsu D3011 Bedienungsanleitung

Fujitsu

Fujitsu Mainboard D2974 Bedienungsanleitung

Fujitsu

Fujitsu MB91470 SERIES Bedienungsanleitung

Fujitsu

Fujitsu D3141 Bedienungsanleitung

Fujitsu

Fujitsu D3598 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung