Fujitsu 10 ppm Bedienungsanleitung

10V 14V

USER’S MANUAL

10/14 ppm page printer

User’s Manual FM-1

Federal Communications Commission

Radio Frequency Interference Statement

Notice: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio / TV technician for help.

FCC warning: Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

Notes

• Testing of this equipment was performed on model number M3878SA14AV.

• The use of a non-shielded interface cable with the referenced device is prohibited.

The length of the parallel interface cable must be 3␣ meters (10␣ feet) or less. The

length of the serial interface cable must be 15␣ meters (50␣ feet) or less.

• The length of the power cord must be 3 meters (10 feet) or less.

Laser Safety Information

This printer has been designed and manufactured according to FDA regulations

“title 21, CFR, chapter I, subchapter J, based on the Radiation Control for Health

and Safety Act of 1968”, and is classified as class 1 laser product.

Warning: Use of controls, adjustments or performance of procedures other than

those specified herein may result in hazardous radiation exposure.

This class B digital apparatus meets all requirements of the Canadian Interference-

Causing Equipment Regulations.

Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur

le matériel brouilleur du Canada.

Bescheinigung des Herstellers/Importeurs

Hiermit wird bescheinigt, daß der/die/das

• Maschinenlärminformationsverordnung 3. GSGV, 18.01.1991: Der höchste

Schalldruckpegel beträgt 70 dB (A) oder weniger gemäß EN27779-1991.

Notice to American

Users

Notice to Canadian

Users

Notice to German

Users

Notice to Japanese

Users

@– u˝C æ u dgÆQ' K§ƒc iubbhj

ˆ› æ æZp u¯•D– u˝C˘º´«¯gp•Ø–˘

I˘ ˜¢ •“C– u“ WI e rW M@ ˜g

p‡ŒØ˘CdgWQ ł«N–•–˘“ Ł •D

@ ]`˜‡¢Ł¢ ˜”‡¢D

FM-2 User’s Manual

In case that the interface board, Ethernet C, is installed, this equipment complies

with EMI regulations as follows:

Notice to American

Users

Federal Communications Commission

Radio Frequency Interference Statement

Notice: This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to correct the

interference at his own expense.

FCC warning: Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

Notes

• Testing of this equipment was performed on model number M3878SA14AV.

• The use of a non-shielded interface cable with the referenced device is prohibited.

The length of the parallel interface cable must be 3␣ meters (10␣ feet) or less. The

length of the Ethernet interface cable must be 100␣ meters (328␣ feet) or less for type

10BASE-2 and 185 meters (607 feet) or less for type 10BASE-T.

• The length of the power cord must be 3 meters (10 feet) or less.

Laser Safety Information

This printer has been designed and manufactured according to FDA regulations

“title 21, CFR, chapter I, subchapter J, based on the Radiation Control for Health

and Safety Act of 1968”, and is classified as class 1 laser product.

Warning: Use of controls, adjustments or performance of procedures other than

those specified herein may result in hazardous radiation exposure.

This class A digital apparatus meets all requirements of the Canadian Interference-

Causing Equipment Regulations.

Cet appareil numérique de la Classe A respecte toutes les exigences du Règlement sur

le matériel brouilleur du Canada.

Bescheinigung des Herstellers/Importeurs

Hiermit wird bescheinigt, daß der/die/das

• Maschinenlärminformationsverordnung 3. GSGV, 18.01.1991: Der höchste

Schalldruckpegel beträgt 70 dB (A) oder weniger gemäß EN27779-1991.

Warning: This is a product which meets Class A of AS/NZS3548 and EN55022.

In a domestic environment this product may cause radio interference in which case

the user may be required to take adequate measures.

Notice to German

Users

Notice to European

and Oceanian Users

@– u˝C æ u dgÆQ' K§ƒc iubbhj

ˆ› Œ æZp u¯•D– u ˘º´«¯gp•Ø˘dgW

Q ł«N–•–˘“ Ł •D– Œ ˝gp “K ¨˛ u‚Ø

⁄v ‡ŒØ–˘“ Ł •D

Notice to Canadian

Users

Notice to Japanese

Users

User’s Manual FM-3

As an International ENERGY STARSM Partner, Fujitsu Limited has determined that

this product meets the International ENERGY STAR Office Equipment Program for

energy efficiency.

The International ENERGY STAR Office Equipment Program is an international

program that promotes energy saving through the use of computers and other office

equipments. The program backs the development and dissemination of products

with functions that effectively reduce energy consumption. It is an open system in

which business proprietors can participate voluntarily. The targeted products are

office equipment such as computers, displays, printers, facsimiles, and copiers.

Their standards and logos are uniform among participating nations.

This product sold in Europe conforms to the standards in accordance with EC

Directives. The copy of “Declaration of Conformity” is attached in the next page.

CE Declaration

FM-4 User’s Manual

User’s Manual FM-5

The contents of this manual may be revised without prior notice and

without obligation to incorporate changes and improvements into units

already shipped.

Fujitsu has made every effort to ensure that the information included

here is complete and accurate at the time of publication. The company

assumes no liability for errors and omissions.

reproduced or translated, stored in a database or retrieval system, or

transmitted, in any form or by any means, electronic, mechanical,

photocopying, recording, or otherwise, without the prior written

permission of Fujitsu Limited.

C145-E145-02EN, November 1996

Trademark Acknowledgment

Fujitsu is a registered trademark of Fujitsu

Limited. The following companies own

the other trademarks used in this manual:

Adobe Systems, Inc.: PostScript

Agfa Division of Miles Inc.: Albertus,

Antique Olive, Arial, CG Omega, CG

Times, Clarendon Condensed, Coronet,

Courier, Garamond, Letter Gothic,

Marigold, Symbol, Times New Roman,

Univers, Univers Condensed, Wingdings

Apple Computer, Inc.: AppleTalk,

LocalTalk, Macintosh, TrueType

AT&T: UNIX

Centronics Data Computer Corporation:

Centronics

Hewlett-Packard Corporation: Hewlett-

Packard, LaserJet, LaserJet 4, PCL

International Business Machines

Corporation: IBM, IBM PC/AT, IBM

PS/2, PC-DOS

Microsoft Corporation: Microsoft, MS-

DOS, Windows

Lexmark: MarkVision

Miles, Inc.: Intellifont

Novell, Inc.: Netware

Xerox Corporation: 4024, Ethernet,

Xerox

FM-6 User’s Manual

Precautions

Read this section and remember these instructions to ensure your safety and

your printer’s correct performance. Follow the cautions and notices labeled on

the printer or marked with icons in the manual. Save this manual for future

reference.

• Use only the power cord furnished with the printer and a properly grounded

outlet. Do not use an extension power cord.

• Confirm that the rated voltage of your printer matches the voltage of your

power outlet. The maximum wattage of the printer is 600 watts.

• Turn off the printer and disconnect the power cord before beginning

maintenance operations.

• Disconnect the power cord from the outlet whenever you are not using the

printer for an extended period of time.

• Disconnect the power cord from the outlet whenever thunder storms are

nearby. Leaving the power cord connected may allow damage to the printer

or other property.

• Do not put the printer in direct sunlight, near a heater, or near water. Leave

adequate space around the printer.

• Do not touch any connector contacts and corona wires. This could cause

electrostatic damage to the printer.

• Do not touch the heat roller and motors if you have been printing recently.

These parts may be hot.

• Do not touch or scratch the green drum surface, and do not expose it to light

for more than three minutes.

• Use only a shielded interface cable of 3 meters (10 feet) or less for the parallel

interface, 15 meters (50 feet) or less for the serial interface, 100 meters (328

feet) or less for Ethernet interface 10BASE-T connection, and 185 meters

(607 feet) or less for the Ethernet interface 10BASE-2 connection.

• Be sure the printer is turned off before connecting the interface.

• Do not turn the printer off while it is printing.

• Do not disassemble or remove any components unless instructed in the

maintenance procedures.

• Keep the print unit upright when removing or installing it.

• Do not apply excessive pressure on the corona wire when cleaning it.

• Do not use alcohol or other cleaning solutions on the drum surface or on any

interior parts of the printer.

• Clear paper jams quickly, especially when they occur in the heat roller unit.

• Do not drop small objects, such as paper clips, into the printer.

• Do not set page margins off the physically printable page area.

• Turn off the printer and disconnect the power cord immediately if an

abnormal condition occurs: for instance, if the printer smokes, prints

abnormally, becomes wet, or falls. Then consult your dealer.

User’s Manual i

Contents

Preface ............................................................................................ v

Manual and Floppy Disks................................................................. v

Operating Environments ................................................................. vi

Conventions .................................................................................... vi

Control Panel........................................................................... vii

Chapter 1 Getting Started ........................................................................... 1–1

Getting Acquainted ..................................................................... 1–1

Getting Ready ............................................................................. 1–4

Picking a Suitable Location ................................................... 1–4

Unpacking and Checking Your Printer ................................. 1–5

Setting Up ................................................................................... 1–7

Preparing the Print Unit and Installing the Toner Bottle ...... 1–7

Loading Paper and Installing the Paper Tray ....................... 1–10

Connecting the Power Cord ............................................... 1–12

Connecting the Printer to Your Computer ................................ 1–13

About Interfacing ................................................................ 1–13

Connecting to the Parallel Port ........................................... 1–14

Printing a Test Page Offline ................................................ 1–15

Installing the Printer Driver....................................................... 1–16

Get to Know Your Printer Driver ....................................... 1–16

Printer Driver for Windows 3.1/3.11 .................................. 1–17

Printer Driver for Windows 95 ........................................... 1–17

Plug and Play Printer Detection ................................... 1–17

Set-up from Printers Folder .......................................... 1–18

Printing Your First Document ................................................... 1–19

Adjusting Print Density ...................................................... 1–20

If Something Goes Wrong .................................................. 1–21

Where To Go From Here .......................................................... 1–22

ii User’s Manual

Chapter 2 Using Printer Software ............................................................... 2–1

Remote Setup Utility Program, PPMENU .................................. 2–1

Installing PPMENU ............................................................. 2–2

Factory Defaults .................................................................... 2–4

Printer Management Utility Program, Lexmark’s MarkVision ..... 2–6

Installing MarkVision ........................................................... 2–6

Menu Bar Functions ............................................................. 2–7

Chapter 3 Printing and Paper Handling ...................................................... 3–1

Control Panel Tutorial ................................................................ 3–1

The Control Panel ................................................................ 3–1

Indicators ....................................................................... 3–2

Message Display ............................................................. 3–3

Buttons........................................................................... 3–3

Control Panel Functions.............................................................. 3–5

Printing Data Remaining in the Buffer ................................. 3–5

Clearing an Error Condition to Continue Printing ............... 3–5

Clearing the Buffer and Reinitializing the Printer.................. 3–6

Printing a Status Report ........................................................ 3–6

Printing a Font Report .......................................................... 3–8

Selecting Paper Tray, MFF, or Manual Paper Feed ............. 3–10

Setting MFF Paper Size ....................................................... 3–11

Selecting Menu Option and Resetting Menu ...................... 3–12

Menu Functions ........................................................................ 3–12

Menu Structure and How to Use Control Panel Buttons .... 3–12

Submenus, Items, and Options ........................................... 3–13

Menu Items ............................................................................... 3–16

Handling Paper ......................................................................... 3–19

Paper Types and Sizes ......................................................... 3–19

General Tips................................................................. 3–22

Preprinted Sheets.......................................................... 3–22

Transparencies .............................................................. 3–22

Envelopes ..................................................................... 3–23

Labels ........................................................................... 3–24

Changing the Paper Tray Size ............................................. 3–24

Feeding Paper Manually...................................................... 3–27

Setting Up the Rear Stacker ................................................ 3–28

Printing on Nonstandard Size Paper and on Envelopes ....... 3–29

Considerations on Paper Size........................................ 3–29

Page Orientation .......................................................... 3–30

Contents

User’s Manual iii

Chapter 4 Enhancing and Customizing the Printer ..................................... 4–1

Adding RAM ............................................................................... 4–1

Installing an Alternate Emulation ................................................ 4–3

Installing an Interface Expansion Board ....................................... 4–4

Installing an Interface Board ................................................. 4–4

Connecting to the Serial Port ................................................ 4–5

Connecting the Serial Interface Cable ............................. 4–5

Selecting the Serial Interface ........................................... 4–6

Verifying Serial Parameter Settings ................................. 4–6

Connecting to the LocalTalk Port ......................................... 4–7

Connecting the LocalTalk Interface Cable...................... 4–8

Selecting the LocalTalk Interface .................................... 4–8

LocalTalk Specifications ................................................. 4–8

Connecting to the Ethernet Port ........................................... 4–9

Connecting the Ethernet Interface Cable ........................ 4–9

Selecting the Ethernet Interface .................................... 4–10

Ethernet Specifications ................................................. 4–10

Adding Paper Sources ................................................................ 4–10

Paper Feeder ....................................................................... 4–10

Changing the Paper Tray Size ............................................. 4–12

Different Paper Tray Sizes................................................... 4–15

Multi-function Feeder......................................................... 4–15

Chapter 5 Maintenance .............................................................................. 5–1

Preventive Maintenance............................................................... 5–1

Periodic Routine Maintenance .................................................... 5–2

Replacing the Toner Bottle ................................................... 5–2

Replacing the Print Unit and Internal Cleaning .................... 5–5

Removing the Print Unit ................................................ 5–6

Cleaning the Paper Path ................................................. 5–7

Cleaning the Corona Wire ............................................. 5–8

Cleaning the Paper Guide before the Corona Wire......... 5–9

Installing the New Print Unit ....................................... 5–10

Resetting the Print Unit Counter ................................. 5–13

Cleaning the Precharger Wire ............................................. 5–15

Repacking the Printer ................................................................ 5–16

Contents

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Fujitsu Drucker Handbücher

Fujitsu

Fujitsu FTP-628WSL210 Series Bedienungsanleitung

Fujitsu

Fujitsu Impact 4550 PRO Bedienungsanleitung

Fujitsu

Fujitsu S510 - ScanSnap - Document Scanner Konfigurationshandbuch

Fujitsu

Fujitsu fi-4x20 SERIES Konfigurationshandbuch

Fujitsu

Fujitsu FTP-642MCL001 Bedienungsanleitung

Fujitsu

Fujitsu fi-7480 Bedienungsanleitung

Fujitsu

Fujitsu fi-4860C Konfigurationshandbuch

Fujitsu

Fujitsu SP320Q Bedienungsanleitung

Fujitsu

Fujitsu FTP-628 Series Bedienungsanleitung

Fujitsu

Fujitsu Fi-718PR Handbuch

Fujitsu

Fujitsu FP-510II Bedienungsanleitung

Fujitsu

Fujitsu DL6400PRO Bedienungsanleitung

Fujitsu

Fujitsu DL3800 Pro Bedienungsanleitung

Fujitsu

Fujitsu FTP-628WSL Bedienungsanleitung

Fujitsu

Fujitsu FTP-639MCL054 Bedienungsanleitung

Fujitsu

Fujitsu FTP-638WSL Bedienungsanleitung

Fujitsu

Fujitsu FTP-631MCL101 Bedienungsanleitung

Fujitsu

Fujitsu DotMax 24 series Bedienungsanleitung

Fujitsu

Fujitsu Breeze 100 Bedienungsanleitung

Fujitsu

Fujitsu VM2200 Bedienungsanleitung

Fujitsu

Fujitsu DL7600 Bedienungsanleitung

Fujitsu

Fujitsu FP-1000 Bedienungsanleitung

Fujitsu

Fujitsu DL7400 Bedienungsanleitung

Fujitsu

Fujitsu FP-1000 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung