Fujitsu SE310 Bedienungsanleitung

English

Fujitsu Server BS2000 SE Series

Server Unit x86

Operating Manual

Valid for:

SE700(B) / SE500(B) / SE300(B) (basic software V6.2A and higher)

SE710 / SE310 (basic software V6.3A and higher)

SE320 (basic software V6.4A and higher)

Edition March 2021

Comments… Suggestions… Corrections…

The User Documentation Department would like to know your opinion on this manual. Your feedback helps us to

optimize our documentation to suit your individual needs.

Feel free to send us your comments by e-mail to: .

[email protected]

Certified documentation according to DIN EN ISO 9001:2015

To ensure a consistently high quality standard and user-friendliness, this documentation was created to meet the

regulations of a quality management system which complies with the requirements of the standard DIN EN ISO

.9001:2015

Delivery subject to availability; right of technical modifications reserved.

All hardware and software names used are trademarks of their respective manufacturers.

The Xen® mark is a trademark of Citrix Systems, Inc., which manages the mark on behalf of the Xen open source

community. The Xen® mark is registered with the U.S. Patent and Trademark Office, and may also be registered in

other countries.

Novell and SUSE are registered brands of Novell, Inc. in the USA and other countries.

Linux is a registered brand of Linus Torvalds.

Windows® is a registered trademark of Microsoft Corporation.

The Linux-based basic software M2000, X2000, and HNC which is installed on the Management Unit, Server Unit

x86, and HNC contains Open Source Software. The licenses for this can be found in the LICENSES directory on

the relevant installation DVD.

Table of Contents
Server Unit x86 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Server Unit SU x86 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1 Switching the Server Unit on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2 Front of the Server Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.1 Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.2 Indicators on the operating panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.3 Indicators on the operable drives/components . . . . . . . . . . . . . . . . . . . . . . . . 15
2.4 Hard disks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.5 DVD-RW drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3 Rear of the Server Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
What to do if ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Related publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Server Unit x86

1 Introduction

The FUJITSU Server BS2000 SE series is the continuation and integration of technologies from the previous Fujitsu

mainframe lines of the S and SQ series as regards hardware architecture and software functions. Designed as

hybrid systems, the SE servers bring a high quality of openness and integration ability from various server and

peripheral systems together with comprehensive, cross-system manageability.

Depending on requirements, an SE server contains all the system components needed for operation as an overall

application:

/390-based BS2000 Server Unit

x86-based Server Unit with BS2000 guest systems

x86-based Application Units for operating Native or hypervisor systems (e.g. Linux, Windows, VMware, OVM,

etc.)

Net Unit as a high-speed, server-internal infrastructure to connect the components with each other and with the

customer's IP networks

Shareable tape and disk periphery

Infrastructure to connect the components with the customer's FC networks

Information on the hardware lifecycle of the FUJITSU Server BS2000 SE Series (Changes

since the last edition of the manual)

With the hardware lifecycle of the SE Series, the hardware basis for the Server Unit x86, the Management Unit and

the HNC has been renewed several times. If the following generations are not identified by their own designations

(e.g. SU300 SU300B SU310 SU320), the generations are identified by a subsequent Mx with x = 1,2,3,…: MU

M2, MU M3, HNC M2, HNC M3 etc. The generation M2 is supported as of SE V6.2A, the generation M3 as of

version 6.3A04.

The changes in the manuals are mainly due to these new hardware lifecycle generation models. Any differences to

the previous models regarding structure and operation are described in detail.

Information on using the manual

The Operating Manual consists of a number of modules and describes the features and hardware components of

the FUJITSU BS2000 servers of the SE series. Users should read the operating manuals carefully in order to obtain

optimal performance from the SE server.

This manual describes the hardware component Server Unit x86 and complements the Basic Operating Manual [ ].

You will find a comprehensive introductory chapter in the Basic Operating Manual. The chapters "Important notes"

on SE server operation and "Environmental protection and service" are contained only in the Basic Operating

Manual.

In the following, abbreviations are used to describe the SE server models and their components. These are

explained in the introduction to the Basic Operating Manual [ ] in the section "Models, Names, Abbreviations".

2 Server Unit SU x86

This section describes the Server Units SU300, SU310 and SU320. SE300(B) is equipped with an SU300 as the

first Server Unit. SE300, SE500 and SE700 can optionally be equipped with one or two additional Server Units

SU300. SE310 is equipped with an SU310 as Server Unit, SE320 with an SU320 as Server Unit.

In the SU x86 the base system X2000 enables BS2000 to execute (in Native mode or on BS2000 VMs).

An SU300 occupies four height units (HUs) in the rack, an SU310 occupies two HUs and an SU320 occupies three

HUs.

Features

For SU300 16 models are available with up to 16 BS2000 processors. For SU310 and SU320 there are 3 models

with 4 processors (16 cores) each. Capacity on Demand permits temporary processor attachment.

Depending on the model, the size of the main memory (for BS2000 and for the base system X2000) is 32 to 128

GB in the basic configuration. These models can be enhanced to up to 512 GB (SU310 and SU320) resp. 1504

GB (SU300) or 2912 GB (SU300B).

For the input/output system the Server Unit contains two 2.5'' SAS (on SU310 and SU320) resp. SATA (on

SU300) hard disks, each with a capacity of 600 GB in size in the basic configuration, which are mirrored.

The Server Unit contains a DVD-RW drive.

Fibre Channels operating at 8 or 16 Gbps are available for connecting peripherals.

At least one 4-port LAN card is connected on the Server Unit. The first two ports are used for the connection to

the Net Unit, and the other two can, if required, be used for BS2000 applications. Optionally LAN controllers

operating at 10 Gbps can also be used.

Each Server Unit is equipped with 4 power supply units. 2 + 2 redundancy in 2 phases is thus guaranteed. If one

phase fails completely, the Server Unit will continue to operate.

Components and ports which are not used are not described below.

2.1 Switching the Server Unit on/off

Information on switching on and starting the SE server and on switching it off and shutting it down is provided in the

"Basic Operating Manual" [ ], section "Switching the server on and off".

Switching the Server Unit on

Before the Server Unit is switched on, the power status indicator lights up green (item 5 in ) resp. on

figure 3/4

SU320 the status indicator (item 1 in ) lights up white.figure 6

>As the administrator, BS2000 administrator or a privileged operator, switch on the Server Unit using the SE

Manager (menu , tab, symbol for the Server Unit), see the “Operation and

Hardware -> Units Units Switch on

Administration” manual [ ].5

The On/Off switch / status indicator lights up green (item 4 in resp. item 1 in ). The Server Unitfigure 3/4 figure 1

switches on, conducts a system test and starts X2000.

If automatic IPL is configured for BS2000, the BS2000 system (Native or as a VM2000 monitor system) is also

started with the configured settings.

Switching the Server Unit off

Before the Server Unit is switched off, the On/Off switch / status indicator lights up green, and after the Server Unit

has been switched off it no longer lights up resp. on SU320 lights up white (item 4 in resp. item 1 in

figure 3/4 figure

).6

>As the administrator, BS2000 administrator or a privileged operator, switch off the Server Unit using the SE

Manager (menu , tab, symbol for the Server Unit), see the “Operation and

Hardware

Units Units Switch off

Administration” manual [ ].5

When the Server Unit is switched off, the BS2000 system is shut down properly taking into account the remaining

runtime specified.

The power status indicator (item 5 in , not on SU320) lights up green when the server is switched off but

figure 3/4

connected to the power supply (power cable connected).

This status indicator does not light up in the following situations:

The Server Unit is switched off and not connected to the power source.

The Server Unit is switched on and operating normally.

On SU320 the power status indicator is integrated into the On/Off switch / status indicator. The On/Off switch /

status indicator lights up white when the Server Unit is switched off, but connected to the power supply (power

cable connected).

The On/Off switch / status indicator does not light up when the SU320 is switched off and not connected to the

power supply. It lights up green when the Server Unit is switched on and is in normal operation mode.

2.2 Front of the Server Unit

Figure 1: Server Unit SU300 (front)

Figure 2: Server Unit SU310 (front)

No. Meaning

1 ID card (green)

2 ServerView Local Service Display (SU300 only)

3 Optical drive activity indicator

4 Operating panel (for further details see )figure 3/4

5 Video port (for Customer Support only)

6 USB ports (3x on SU300, 2x on SU310, for Customer Support only)

7 HDD indicators

Figure 3: Front - Detailed view: Operating panel

Figure 4: Front - Detailed view: Operating panel

No. Meaning

1 ID button/ ID indicator

2 Reset button

3 NMI button

4 On/Off button / Status indicator

5 Status indicator (power cable connected)

6 3x resp. 2x USB ports (for Customer Support only)

7 Video port (for Customer Support only)

8 HDD activity indicator

9 Global error indicator

10 CSS indicator

Figure 5: Server Unit SU320 (front)

No. Meaning

1 ID card

2 Optical disk drive (optional)

3 Video port (for Customer Support only)

4 Operating panel (for further details see figure 6)

5 2.5-inch HDDs/SSDs/PCIe-SSDs (8x, 16x or 24x)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Fujitsu Server Handbücher

Fujitsu

Fujitsu Primergy RX300 S2 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY RX1330 M1 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY TX150 S6 Leitfaden

Fujitsu

Fujitsu PRIMERGY TX150 S4 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY RX600 S3 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY RX4770 M4 Bedienungsanleitung

Fujitsu

Fujitsu PRIMEQUEST 2800B3 Bedienungsanleitung

Fujitsu

Fujitsu PRIMEQUEST 2000 Series Leitfaden

Fujitsu

Fujitsu PRIMEQUEST 1000 Series Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY RX100 S8 Bedienungsanleitung

Fujitsu

Fujitsu SPARC Enterprise M8000 Installationsanleitung

Fujitsu

Fujitsu PRIMERGY BX920 S2 Bedienungsanleitung

Fujitsu

Fujitsu PRIMEQUEST 2000 Series Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY RX600 S3 Leitfaden

Fujitsu

Fujitsu SPARC Enterprise T5440 Server Bedienungsanleitung

Fujitsu

Fujitsu PRIMEQUEST 2000 Series Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY TX1320 M4 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY RX2530 M1 Bedienungsanleitung

Fujitsu

Fujitsu Primergy RX300 S3 Betriebsanleitung

Fujitsu

Fujitsu PRIMERGY RX300 S8 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY BX600 Leitfaden

Fujitsu

Fujitsu PRIMERGY BX600 S3 Betriebsanleitung

Fujitsu

Fujitsu PRIMERGY TX200 S2 Leitfaden

Fujitsu

Fujitsu PRIMERGY TX1310 M5 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung