Fujitsu ETERNUS DX60 S3 Bedienungsanleitung

FUJITSU Storage

ETERNUS DX

Configuration Guide -Server Connection-

(Fibre Channel) ETERNUS DX60 S3/DX100 S3/DX200 S3,

ETERNUS DX500 S3/DX600 S3,

ETERNUS DX8700 S3/DX8900 S3 Disk Storage System,

ETERNUS DX200F All Flash Array Settings

P3AM-7962-08ENZ0

This page is intentionally left blank.

Preface

This manual briefly explains the operations that need to be performed by the user in order to connect an

ETERNUS DX to a server running Solaris OS, HP-UX, AIX, Windows®, Linux, VMware ESX, PAN Manager, Citrix®

XenServer®, Oracle Linux, or Oracle VM Server for x86 via a Fibre Channel interface.

This manual should be used in conjunction with any other applicable user manuals, such as those for the

ETERNUS DX, server, OS, Fibre Channel cards, and drivers.

Refer to "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Notations" for the notations

used in this manual such as product trademarks and product names. For storage systems that are supported

by the OS, refer to the Server Support Matrix of the ETERNUS DX.

8th Edition

June 2015

The Contents and Structure of this Manual

This manual is composed of the following two chapters.

•"Chapter 1 Workflow" (page 6)

This chapter describes the workflow when setting up a storage system.

•"Chapter 2 Setting Up the ETERNUS DX" (page 8)

This chapter describes how to set up a storage system.

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-

P3AM-7962-08ENZ0

Table of Contents

Chapter 1 Workflow 6

Chapter 2 Setting Up the ETERNUS DX 8

2.1 Common Settings ........................................................................................................................... 8

2.1.1 Setting the To-Server Connection Type (Setting the FC Port Parameters)..............................................................8

2.1.2 Creating the Server Accessible LUN Groups (Setting the LUN Groups)...................................................................9

2.1.3 Setting the Host Responses ................................................................................................................................10

2.1.4 Setting the CA Port Groups..................................................................................................................................10

2.1.5 Registering the WWNs of the Accessing Fibre Channel Cards (Setting FC Host)...................................................10

2.1.6 Allocating LUN Groups (Setting the Host Affinity)...............................................................................................11

2.2 Specific Settings ........................................................................................................................... 11

2.2.1 Setting the CA Reset Groups................................................................................................................................11

2.2.2 Setting the Subsystem Parameters .....................................................................................................................11

2.3 Checking the WWNs ..................................................................................................................... 11

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-

P3AM-7962-08ENZ0

List of Tables

Table 2.1 FC port parameter settings (FC-AL connection) ..........................................................................................8

Table 2.2 Transfer Rate setting values (for FC-AL connection) ...................................................................................8

Table 2.3 FC port parameter settings (Fabric connection) .........................................................................................8

Table 2.4 Transfer Rate setting values (for Fabric connection) ..................................................................................9

Table 2.5 Host response settings .............................................................................................................................10

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-

P3AM-7962-08ENZ0

Chapter 1

Workflow

This manual is used when performing the setup procedures described in the "Setting Up the ETERNUS DX"

section of the "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel)" for

each OS.

Required Documents

•"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) Fibre Channel

Switch Settings"

•"Fabric OS Administrator's Guide Supporting Fabric OS"

•"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris"

•"ETERNUS Web GUI User's Guide"

Workflow

Setting the FC Port Parameters

Set the to-server connection type.

•"2.1.1 Setting the To-Server Connection Type (Setting the FC Port Parameters)" (page 8)

Setting the LUN Groups

Set the server accessible LUN groups.

•"2.1.2 Creating the Server Accessible LUN Groups (Setting the LUN Groups)" (page 9)

Setting the Host Responses

Set the host responses to match the connection configuration.

•"2.1.3 Setting the Host Responses" (page 10)

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-

P3AM-7962-08ENZ0

Setting the CA Port Groups

Create a group of ports for each CA type.

•"2.1.4 Setting the CA Port Groups" (page 10)

Setting the FC Host

•"2.1.5 Registering the WWNs of the Accessing Fibre Channel Cards (Setting FC Host)" (page 10)

Setting the Host Affinity

Define the relationship between the FC host, the CA port group, and the LUN group.

•"2.1.6 Allocating LUN Groups (Setting the Host Affinity)" (page 11)

Setting the Specific Parameters

Set the required parameters according to the OS and the connection configuration.

•"2.2 Specific Settings" (page 11)

Checking the WWNs

Check information that is necessary for connecting to the server.

•"2.3 Checking the WWNs" (page 11)

After completing all the required procedures in this manual, follow the procedures in "FUJITSU Storage

ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel)" for each OS.

Chapter 1 Workflow

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-

P3AM-7962-08ENZ0

Chapter 2

Setting Up the ETERNUS DX

2.1 Common Settings

This section explains the settings required for all server OSs, regardless of the connection configuration.

See the "ETERNUS Web GUI User's Guide" for details of how to set up and operate ETERNUS Web GUI.

2.1.1 Setting the To-Server Connection Type (Setting the FC Port Parameters)

For each connection configuration, set the indicated items only. All other parameters should be left on their

default values.

•Specify "Fabric connection" for connections to the Fibre Channel switches.

•Specify "FC-AL connection" for direct connections to the Fibre Channel cards. Specify "Fabric connection" for

direct connections to 16Gbit/s Fibre Channel cards (maximum transfer rate) with a transfer rate of 16Gbit/s.

Table 2.1 FC port parameter settings (FC-AL connection)

Parameter Solaris OS

HP-UX, AIX, Windows®, Linux, VMware

ESX, PAN Manager, Citrix XenServer,

Oracle Linux, Oracle VM Server for x86

Connection FC-AL

Set Loop ID Manual

Loop ID Values from 0x10 upwards

(Except 0x7D)

0x00

Transfer Rate See the table below (*1)

Frame Size 2048

Reset Scope I_T_L

Release Reservation if Chip is Reset Disable

*1: Set the appropriate value from the following table. Do not use [Auto-negotiation].

Table 2.2 Transfer Rate setting values (for FC-AL connection)

Fibre Channel card maximum speed Transfer rate setting value

16Gbit/s CA 8Gbit/s CA

16Gbit/s — 8Gbit/s

8Gbit/s 8Gbit/s 8Gbit/s

4Gbit/s 4Gbit/s 4Gbit/s

Table 2.3 FC port parameter settings (Fabric connection)

Parameter Setting value

Connection Fabric

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-

P3AM-7962-08ENZ0

Parameter Setting value

Transfer Rate See the table below (*1)

Frame Size 2048

Reset Scope I_T_L

Release Reservation if Chip is Reset Disable

*1: Set the appropriate value from the following table.

Table 2.4 Transfer Rate setting values (for Fabric connection)

Fibre Channel switch maximum

speed

Transfer rate setting value

16Gbit/s CA 8Gbit/s CA

16Gbit/s 16Gbit/s (*1) 8Gbit/s

8Gbit/s 8Gbit/s 8Gbit/s

4Gbit/s 4Gbit/s 4Gbit/s

*1: Specify "Auto Negotiation" for direct connections to 16Gbit/s Brocade Fibre Channel cards.

Make sure to prepare and set up Fibre Channel switches for Fibre Channel connections. For setting details,

refer to "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) Fibre Chan-

nel Switch Settings" or "Fabric OS Administrator's Guide Supporting Fabric OS".

2.1.2 Creating the Server Accessible LUN Groups (Setting the LUN Groups)

Create LUN groups for the server to access. Refer to "Connectivity Management" in "ETERNUS Web GUI User's

Guide" for details, and set the LUN groups.

Depending on the OS version, the server may not recognize the ETERNUS DX unless a LUN group is as-

signed from LUN0. In this case, assign a LUN group starting from LUN0 in ascending order.

Chapter 2 Setting Up the ETERNUS DX

2.1 Common Settings

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-

P3AM-7962-08ENZ0

2.1.3 Setting the Host Responses

The host response parameters for the ETERNUS DX must be set to match the way the server processes the

responses to requests from the ETERNUS DX. Setting of the host response must be done before connecting

the ETERNUS DX to the server.

Set the parameters that are described below for each OS.

Retain the default values for all of the parameters that are not described below.

When setting the access path using the ETERNUS SF Storage Cruiser, the host responses for FC host will be

set to default values. Set the host response after setting the access path using the ETERNUS SF Storage

Cruiser.

Table 2.5 Host response settings

OS Conditions Host response selection

Solaris (*1) When using the OS standard Multipath Driver

(MPxIO)

Solaris MPxIO

Other cases Default

Windows®

Linux

VMware ESX

Citrix XenServer

Oracle VM Server for x86

– Default

HP-UX – HP-UX

AIX When using Symantec Storage Foundation AIX VxVM

Other cases AIX

IBM SVC – SVC

*1: An Oracle-brand Fibre Channel card driver may be used for Fujitsu Fibre Channel cards.

To confirm which driver should be used, check the "Notes" and "Fibre Channel Cards that Require an Ora-

cle-brand Driver" sections in "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fi-

bre Channel) for Oracle Solaris".

2.1.4 Setting the CA Port Groups

Create new FC port groups and register the ports as members of the groups. A port group is a group of ports

that access the same LUN group (ports that are used for multipath connection to the server or for connecting

to the cluster configuring server). Configure the host affinity setting for each FC port group.

2.1.5 Registering the WWNs of the Accessing Fibre Channel Cards (Setting FC Host)

same time, set the host response numbers registered in "2.1.3 Setting the Host Responses" (page 10) to ac-

cept these WWNs.

Registering the FC host WWNs and setting up Host Affinities as described elsewhere, allows limits to be set

on which servers are allowed to access which ETERNUS DX LUNs.

Chapter 2 Setting Up the ETERNUS DX

2.1 Common Settings

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-

P3AM-7962-08ENZ0

Andere Handbücher für ETERNUS DX60 S3

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Fujitsu Lagerung Handbücher

Fujitsu

Fujitsu ETERNUS DX Disk Bedienungsanleitung

Fujitsu

Fujitsu Eternus DX80 S2 Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS AF650 S2 Montageanleitung

Fujitsu

Fujitsu ETERNUS DX100 S3 Bedienungsanleitung

Fujitsu

Fujitsu SLR 50 GBYTE Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS LT260 Bedienungsanleitung

Fujitsu

Fujitsu MAU3147FC Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS AF250 S2 Technisches Handbuch

Fujitsu

Fujitsu ETERNUS Multipath Driver V2 Bedienungsanleitung

Fujitsu

Fujitsu M2488 Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS LT260 Bedienungsanleitung

Fujitsu

Fujitsu MAT3300NC Bedienungsanleitung

Fujitsu

Fujitsu GP5-HDH8B Bedienungsanleitung

Fujitsu

Fujitsu MAN3735 SERIES Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS4000' ETERNUS8000 Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS DX60 S3 Bedienungsanleitung

Fujitsu

Fujitsu HandyDrive-5 Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS DX Disk Bedienungsanleitung

Fujitsu

Fujitsu MHV2100BH Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS DX8100 S4 Technisches Handbuch

Fujitsu

Fujitsu GRANPOWER 5000 GP5-HDH451 Bedienungsanleitung

Fujitsu

Fujitsu MAU3147RC SERIES Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS DX Disk Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS DX S4 Series Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung