Fujitsu MHV2160BT - 160GB SATA/150 4200RPM 8MB Notebook Hard... Bedienungsanleitung

CHAPTER 3 Installation Conditions

3.1 Dimensions

3.2 Mounting

3.3 Connections with Host System

This chapter gives the external dimensions, installation conditions, surface

temperature conditions, cable connections, and switch settings of the hard disk

drives.

C141-E244 3-1

Installation Conditions

3.1 Dimensions

Figure 3.1 illustrates the dimensions of the disk drive. All dimensions are in mm.

*1 The PCA and connectors are not included in these dimensions.

*2 Dimension from the center of the user tap to the base of the connector pins

*3 Length of the connector pins

*4 Dimension from the outer edge of the user tap to the center of the connector

pins

*5 Dimension from the outer edge of the user tap to the innermost edge of the

connector pins

Figure 3.1 Dimensions

3-2 C141-E244

3.2 Mounting

For information on mounting, see the "FUJITSU 2.5-INCH HDD

INTEGRATION GUIDANCE (C141-E144)."

(1) Orientation

The disk drives can be mounted in any direction.

(2) Frame

The MR head bias of the HDD disk enclosure (DE) is zero. The mounting frame

is connected to Signal Ground (SG).

IMPORTANT

Use M3 screw for the mounting screw and the screw length should

satisfy the specification in Figure 3.2.

The tightening torque must be 0.49N •m (5kgf •cm).

When attaching the HDD to the system frame, do not allow the

system frame to touch parts (cover and base) other than parts to

which the HDD is attached.

(3) Limitation of mounting

Note) These dimensions are recommended values; if it is not possible to satisfy

them, contact us.

Screw

Details of A

3.0 or less

Frame of system

cabinet

Frame of system

cabinet

PCA

2.52.5

2.5

Side surface

mounting

Bottom surface mounting

Figure 3.2 Mounting frame structure

C141-E244 3-3

Installation Conditions

IMPORTANT

Because of breather hole mounted to the HDD, do not allow this to

close during mounting.

Locating of breather hole is shown as Figure 3.3.

For breather hole of Figure 3.3, at least, do not allow it around φ 2.4

to block.

Figure 3.3 Location of breather

3-4 C141-E244

3.2 Mounting

(4) Ambient temperature

The temperature conditions for a disk drive mounted in a cabinet refer to the

ambient temperature at a point 3 cm from the disk drive. The ambient

temperature must satisfy the temperature conditions described in Section 1.4, and

the airflow must be considered to prevent the DE surface cover temperature from

exceeding 60 °C.

Provide air circulation in the cabinet such that the PCA side, in particular,

receives sufficient cooling. To check the cooling efficiency, measure the surface

cover temperatures of the DE. Regardless of the ambient temperature, this

surface cover temperature must meet the standards listed in Table 3.1. Figure 3.4

shows the temperature measurement point.

Figure 3.4 Surface cover temperature measurement points

Table 3.1 Surface temperature measurement points and standard values

No. Measurement point Temperature

1 DE cover 60 °C max

C141-E244 3-5

Installation Conditions

3-6 C141-E244

(5) Service area

Figure 3.5 shows how the drive must be accessed (service areas) during and after

installation.

Figure 3.5 Service area

Data corruption: Avoid mounting the disk drive near strong

magnetic sources such as loud speakers. Ensure that the disk drive

is not affected by external magnetic fields.

Damage: Do not press the cover of the disk drive. Pressing it too

hard, the cover and the spindle motor contact, which may cause

damage to the disk drive.

Static: When handling the device, disconnect the body ground

(500 kΩor greater). Do not touch the printed circuit board, but hold

it by the edges.

(6) Handling cautions

Please keep the following cautions, and handle the HDD under the safety

environment.

Mounting

screw hole

Mounting screw hole

Cable connection

3.2 Mounting

- General notes

ESD mat

Shock absorbing mat

Wrist strap

Use the Wrist stra

. Place the shock absorbing mat on the

operation table, and place ESD mat on it.

Do not hit HDD each other. Do not stack when carr

Do not

lace HDD verticall

to avoid fallin

down. Do not dro

Figure 3.6 Handling cautions

- Installation

(1) Please use the driver of a low impact when you use an electric driver.

HDD is occasionally damaged by the impact of the driver.

(2) Please observe the tightening torque of the screw strictly.

M3 ······· 0.49N •m (5 kgf •cm).

- Recommended equipments

Contents Model Maker

Wrist strap JX-1200-3056-8 SUMITOMO 3MESD

ESD mat SKY-8A (Color Seiden Mat) Achilles

Shock Low shock driver SS-6500 HIOS

C141-E244 3-7

Installation Conditions

3.3 Connections with Host System

3.3.1 Device connector

The disk drive has the SATA interface connectors listed below for connecting

external devices. Figure 3.7 shows the locations of these connectors and

terminals.

SATA interface

and power

connectors

PCA

Figure 3.7 Connector locations

3-8 C141-E244

3.3 Connections with Host System

3.3.2 Signal segment and power supply segment

Figure 3.8 shows each segment of the SATA interface connector and pin

numbers.

Power suppl

segment

P1 pins in the power

supply segment

S1 pins in the si

nal

segment

View from the

connector side

View from the

PCA side

nal se

ment

Figure 3.8 Power supply pins (CN1)

3.3.3 Connector specifications for host system

Table 3.2 lists the recommended specifications for the host interface connectors.

Table 3.2 The recommended connector specifications for the host system

Segment Name Model (Manufacturer)

SATA interface

and power supply Host receptacle 67492-0220 (Molex) or compatibles

C141-E244 3-9

Installation Conditions

3-10 C141-E244

3.3.4 SATA interface cable connection

The cable that connects the disk drive to the host system must be compliant with

the Serial ATA 1.0a specification.

3.3.5 Note about SATA interface cable connection

Take note of the following precaution about plugging a SATA interface cable into

the SATA interface connector of the disk drive and plugging the connector into a

host receptacle:

When plugging together the disk drive SATA interface connector

and the host receptacle or SATA interface cable connector, do not

apply more than 10 kgf of force in the connection direction once

they are snugly and securely in position.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Fujitsu Lagerung Handbücher

Fujitsu

Fujitsu Eternus CS800 S3 Bedienungsanleitung

Fujitsu

Fujitsu MBC2036RC SERIES Bedienungsanleitung

Fujitsu

Fujitsu MBA3073 SERIES Bedienungsanleitung

Fujitsu

Fujitsu MAY2036RC Product/ Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS AX Series Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS DX60 S2 Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS LT160 Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS DX60 Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS LT140 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY LTO3 Bedienungsanleitung

Fujitsu

Fujitsu DynaMO 640SZI Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS LT140 Bedienungsanleitung

Fujitsu

Fujitsu MAU3147RC SERIES Bedienungsanleitung

Fujitsu

Fujitsu MHY2250BH - Mobile 250 GB Hard Drive Bedienungsanleitung

Fujitsu

Fujitsu MAN3184 SERIES Bedienungsanleitung

Fujitsu

Fujitsu MHZ2320BJ Bedienungsanleitung

Fujitsu

Fujitsu Eternus DX500 S3 Installationsanleitung

Fujitsu

Fujitsu Eternus DX80 S2 Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS Bedienungsanleitung

Fujitsu

Fujitsu M2488 Bedienungsanleitung

Fujitsu

Fujitsu Eternus DX80 S2 Bedienungsanleitung

Fujitsu

Fujitsu RE25U Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS JX40 S2 Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung

HP P9000 Bedienungsanleitung