Furuno MFDBB Bedienungsanleitung

Installation Manual

Multi Function Display

Model MFDBB

SAFETY INSTRUCTIONS ............................................................................ i

SYSTEM CONFIGURATION ....................................................................... ii

EQUIPMENT LISTS.................................................................................... iii

1. MOUNTING............................................................................................ 1

1.1 Mounting the Control Unit.............................................................................................1

1.2 Mounting the Processor Unit ........................................................................................7

2. WIRING .................................................................................................. 9

2.1 Processor Unit Wiring...................................................................................................9

2.2 Control Unit Wiring .....................................................................................................14

3. SETTING UP THE EQUIPMENT ......................................................... 15

3.1 Setup for Single MFD in the Network .........................................................................16

3.2 Setup for Multiple MFDs in the Network .....................................................................30

PACKING LISTS...................................................................................... A-1

OUTLINE DRAWINGS............................................................................. D-1

INTERCONNECTION DIAGRAM ............................................................ S-1

www.furuno.com

ll brand and product names are trademarks, registered trademarks or their respective holder

WARNING

Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation which, if not avoided,

may result in minor or moderate injury.

Warning, Caution

Mandatory Action

Prohibitive Action

SAFETY INSTRUCTIONS

The user and installer must read the appropriate safety instructions before attempting to install

or operate the equipment.

WARNING CAUTION

Ground the equipment to prevent

electrical shock and mutual interference.

Observe the following compass safe distances

to prevent interference to a magnetic compass:

ELECTRICAL SHOCK HAZARD

Do not open the equipment unless

totally familiar with electrical circuits.

Only qualified personnel should work

inside the equipment.

Turn off the power at the switchboard

before beginning the installation.

Fire or electrical shock can result if the

power is left on.

Be sure that the power supply is

compatible with the voltage rating of the

equipment.

Connection of an incorrect power supply

can cause fire or damage the equipment.

Standard

compass Steering

compass

MPU-001 1.45 m 0.90 m

MCU-001 0.55 m 0.40 m

DCU12 0.70 m 0.45 m

Use the proper fuse.

Use of an incorrect fuse may damage the equipment.

SYSTEM CONFIGURATION

MONITOR

MU-155C/170C, etc.

VIDEO IN (CCD

CAMERA, MAX. 4)

LINE OUT

(SPKR, ETC.)

12-24 VDC*2

DISPLAY CONTRO

UNIT DCU12

CONTROL UNIT

MCU-001

AND/OR*3

HUB-101

GPS NAVIGATOR

GP-330B

AIS RECEIVER,

HEADING SENSOR or

EXTERNAL BUZZER

USB DEVICE

(MOUSE, KYBD)

NMEA 2000

(GP-330B, ETC.)

POWER SUPPLY UNIT

PSU-013*1

: Standard Supply

: Optional Supply

: Local Supply

*1 Required with DRS25A

*2 See the table and figure below for

configurations for the PSU and rectifiers.

*3 Max. two units total

PROCESSOR UNIT

MPU-001

RADAR SENSOR

DRS4A/DRS6A/DRS12A/DRS25A

RADAR SENSOR

DRS2D/DRS4D

FISH FINDER

(DFF series, ETR-6/10N,

ETR-30N, FCV-1150)

Matrix for radar model, PSU and rectifiers

DRS2D/4D/

4A/6A/12A

MPU-001

RU-1746B-2

DRS25A

PSU-013

DRS25A

PSU-013

Radar

Model PSU Rectifier for

MFDBB Rectifier for

PSU Rectifier for

MFDBB+PSU

DRS2D Not

required RU-1746B-2

DRS4D

DRS4A

DRS6A

DRS12A

DRS25A PSU-013* RU-1746B-2 RU-3424

* Standard supply with DRS25A.

12-24 VDC*2

RU-1746B-2

12-24 VDC2

LINE IN (MIC,

for future use)

DRS25A

DRS4A

DRS6A

DRS12A

RU-1746B-2 RU-3424

JUNCTION

BOX FI-5002

MPU-001 MPU-001

FAX-30

FA-50

iii

EQUIPMENT LISTS

Standard supply

*See the lists at the back of this manual.

Optional supply

Name Type Code No. Qty Remarks

Processor Unit MPU-001 - 1

Control Unit MCU-001 - 1 Choose one.

Display Control Unit DCU12 - 1

Installation Materials CP19-00600 000-011-664 1 set For MPU-001, Cable, CP19-

00601*

CP19-00700 000-011-663 1 set For MCU-001,

cable, CP19-

00701*

Choose one.

CP19-00800 000-011-662 For DCU12,

cables, CP19-

00801*

Spare Parts SP19-00501 001-023-090 1 set For MPU-001, fuses

SP19-00601 001-023-040 1 set For DCU-001, fuses

Accessories FP19-01201 001-033-760 1 For MCU-001, panel remover

FP19-01101 001-023-060 For DCU12, panel remover

Name Types Code No. Remarks

DVI-D Cable DVI-D/D SINGLELINK 000-149-054-10 5 m

DVI-D/D S-LINK 000-150-200-10 10 m

External Buzzer OP03-136 000-086-443

Rectifier RU-1746B-2 -

Network Hub HUB-101 -

Joint Box TL-CAT-012 000-167-140-10 For LAN cable extension

Junction Box FI-5002 000-010-765 For NMEA 2000

Control Unit MCU-001 -

Display Control

Unit DCU12 -

Cable Assy MJ-A7SPF0007-050C 000-154-028-10 5 m, NMEA0183, w/7P

connector

MJ-A6SPF0016-005C 000-159-689-11 For FAX-30, ETR6N/10N

connection

MOD-Z072-020+ 000-167-175-10 2 m, LAN

MOD-Z072-050+ 000-167-176-10 5 m, LAN

MOD-Z072-100+ 000-167-177-10 10 m, LAN

MOD-Z073-030+ 000-167-171-10 3 m, for PC connection

M12-05BM+05BF-010 000-167-962-10 φ6, 1 m, NMEA 2000

M12-05BM+05BF-020 000-167-963-10 φ6, 2 m, NMEA 2000

M12-05BM+05BF-060 000-167-964-10 φ6, 6 m, NMEA 2000

M12-05BFFM-010 000-167-965-10 φ6, 1 m, NMEA 2000

M12-05BFFM-020 000-167-966-10 φ6, 2 m, NMEA 2000

M12-05BFFM-060 000-167-967-10 φ6, 6 m, NMEA 2000

CB-05PM+05BF-010 000-167-968-10 φ10, 1 m, NMEA 2000

CB-05PM+05BF-020 000-167-969-10 φ10, 2 m, NMEA 2000

CB-05PM+05BF-060 000-167-970-10 φ10, 6 m, NMEA 2000

CB-05BFFM-010 000-167-971-10 φ10, 1 m, NMEA 2000

CB-05BFFM-020 000-167-972-10 φ10, 2 m, NMEA 2000

CB-05BFFM-060 000-167-973-10 φ10, 6 m, NMEA 2000

NMEA connector LTWSS-050505-FMF-

TS001 000-168-603-10 NMEA 2000 distributor

(micro style)

LTWMC-05BMMT-

SL8001 000-168-604-10 NMEA 2000 terminator,

male (micro style)

LTWMC-05BFFT-

SL8001 000-168-605-10 NMEA 2000 terminator,

female (micro style)

LTWNC050505FMF-

TS001 000-160-507-10 NMEA 2000 distributor

(mini style)

LTWMN-05AMMT-

SL8001 000-160-508-10 NMEA 2000 terminator,

male (mini style)

LTWMN-05AFFT-

SL8001 000-160-509-10 NMEA 2000 terminator,

female (mini style)

In-line Terminator FRU-0505-FF-IS 000-172-037-10 NMEA 2000 connector

w/terminator, micro style

Operator’s Manual OME-44460 000-167-217

NMEA 2000 Inter-

face Unit IF-NMEA2K1 -

Name Types Code No. Remarks

1. MOUNTING

1.1 Mounting the Control Unit

There are two types of control units: Control Unit MCU-001 and Display Control Unit DCU12. The

former is the keyboard type, and the latter has an LCD display and keyboard.

When selecting a mounting location for the control unit, keep the following in mind:

• The temperature and humidity at the mounting location should be moderate and stable.

• Locate the unit away from exhaust pipes and ventilators.

• The mounting location should be well ventilated.

• Mount the unit where shock and vibration are minimal.

• Keep the unit away from electromagnetic field generating equipment such as motors and gen-

erators.

• For maintenance and checking purposes, leave sufficient space at the sides and rear of the unit

and leave slack in cables. Minimum recommended space is shown on the outline drawing for

the control units.

• Do not mount the DCU12 on the overhead.

• A magnetic compass will be affected if the control unit is placed too close to it. Observe the

compass safe distances shown in the SAFETY INSTRUCTIONS to prevent disturbance to the

magnetic compass.

•For the flush mount, make sure the mounting location is flat.

1.1.1 Mounting procedure for control unit MCU-001

The control unit MCU-001 is designed to be flush mounted in a console or panel.

1. Prepare a cutout in the mounting location using the template sheet (supplied) for the MCU-

001.

2. Remove the front panel from the MCU-001 by unfastening the catches at the rear of the panel,

in the order as shown in the figure below.

Note: Detach the panel carefully to prevent breakage of the panel.

3. Attach the mounting sponge to the MCU-001.

4. Fix the MCU-001 by using four self-tapping screws (supplied).

5. Attach the front panel to the MCU-001.

How to detach the front panel from the mounting place

To detach the front panel after mounting the unit, use the remover (supplied) as below. Do not

attempt to remove it by any other method, to prevent damage to the unit.

1. Set the remover to the left-side notch at the bottom of the unit.

Mounting

sponge

MCU-001

Cutout

Self-tapping screws

(4 pcs.)

Front panel

MCU-001, rear view

(Location of catches and order to unfasten them)

2. Pull the remover to raise the panel slightly.

3. Similarly use the remover to raise the panel at the right-side notch.

4. Insert the remover to the space at the one end of the unit, and pull it to raise the panel slightly.

Repeat this procedure for the opposite side.

5. Use the remover to raise the panel at the two notches on the upper side of the unit.

6. Use your hands to detach the front panel at both sides of it.

1.1.2 Mounting procedure for display control unit DCU12

The Display Control Unit DCU12 can be flush mounted in a console or panel, or mounted on a

desktop or the overhead.

Flush mounting

1. Prepare a cutout in the mounting location using the template sheet (supplied) for the DCU12.

2. Remove the front panel from the DCU12 by unfastening the catches at the rear of he panel, in

the order as shown in the figure below.

Note: Detach the panel carefully to prevent breakage of the panel.

3. Attach the mounting sponge to the DCU12.

4. Fix the DCU12 by using four self-tapping screws (supplied).

5. Attach the front panel to the DCU12.

How to detach the front panel from the mounting place

To detach the front panel after mounting the unit, use the remover (supplied) as below. Note that

the front cover may be damaged if you do not follow the methods below.

1. Set the remover to a notch on the lower side of the unit.

Mounting

sponge

Front panel

Cutout

Display unit

(ex. MFD12)

Self-tapping screws

(4 pcs.)

MFD, rear view

(Location of catches and

order to unfasten them)

Andere Handbücher für MFDBB

Inhaltsverzeichnis

Andere Furuno Schiffsausrüstung Handbücher

Furuno

Furuno BBWX4 SiriusXM Installationsanleitung

Furuno

Furuno SC-33 Bedienungsanleitung

Furuno

Furuno Sc 50 Handbuch

Furuno

Furuno NAVpilot-700 Bedienungsanleitung

Furuno

Furuno FCV-295 Bedienungsanleitung

Furuno

Furuno FCV-581 Bedienungsanleitung

Furuno

Furuno DFF1 Bedienungsanleitung

Furuno

Furuno FI-503 Bedienungsanleitung

Furuno

Furuno FMD-3200-BB Bedienungsanleitung

Furuno

Furuno Network Sounder DFF3 Bedienungsanleitung

Furuno

Furuno FM-8900S Bedienungsanleitung

Furuno

Furuno DS-50 Bedienungsanleitung

Furuno

Furuno FI70DSW Bedienungsanleitung

Furuno

Furuno FCV-30 Bedienungsanleitung

Furuno

Furuno Multi Instrument FI-504 Bedienungsanleitung

Furuno

Furuno DFF1 Bedienungsanleitung

Furuno

Furuno FELCOM 12 Bedienungsanleitung

Furuno

Furuno FCV-1100L Bedienungsanleitung

Furuno

Furuno Color LCD Sounder FCV-620/585 Bedienungsanleitung

Furuno

Furuno FE-680 Bedienungsanleitung

Furuno

Furuno RD-33 Bedienungsanleitung

Furuno

Furuno FCV-620 Handbuch

Furuno

Furuno LS-6100 Bedienungsanleitung

Furuno

Furuno ETR-10N Bedienungsanleitung

Beliebte Schiffsausrüstung Handbücher anderer Marken

Clarion

Clarion CMS2 Reparaturanleitung

EBS

EBS M7000 Bedienungsanleitung

Kongsberg

Kongsberg M3 Bathy Bedienungsanleitung

NPK

NPK SCS-1002 Bedienungsanleitung

Harken

Harken 1561 Bedienungsanleitung

Simrad

Simrad DD15 Bedienungsanleitung

Notifier

Notifier FS-BSO Bedienungsanleitung

Raymarine

Raymarine ST40 Bedienungsanleitung

E2S

E2S E2XS112UL Bedienungsanleitung

R2Sonic

R2Sonic 2026 Bedienungsanleitung

COBHAM

COBHAM SAILOR 6000 Bedienungsanleitung

Raymarine

Raymarine Maxiview ST80 Benutzerhandbuch

GUIDANCE MARINE

GUIDANCE MARINE 20- Series Montageanleitung

Raymarine

Raymarine ST60 Tridata Benutzerhandbuch

Sonic

Sonic 2024 Bedienungsanleitung

Quicksilver

Quicksilver 88688A25 Handbuch

olympia electronics

olympia electronics ΒS-532/WP Bedienungsanleitung

olympia electronics

olympia electronics ΒS-531/1/MAR Bedienungsanleitung