Furuno GP-7000F Bedienungsanleitung

Installation Manual

COLOR GPS/PLOTTER/SOUNDER

GP-7000F

SAFETY INSTRUCTIONS.......................................................................................................i

SYSTEM CONFIGURATION..................................................................................................ii

EQUIPMENT LISTS ..............................................................................................................iii

1. INSTALLATION.................................................................................................................1

1.1 Display Unit........................................................................................................................1

1.2 Antenna Unit ......................................................................................................................4

1.3 Transducer.........................................................................................................................5

1.4 Optional Speed/Water Temperature Sensor ST-02MSB, ST-02PSB ...............................18

2. WIRING ...........................................................................................................................19

3. ADJUSTMENTS..............................................................................................................26

3.1 Choosing Position Data Source .......................................................................................26

3.2 Choosing Port I/O Format................................................................................................28

3.3 Echo Sounder Settings....................................................................................................30

3.4 Choosing Data Source(s) ................................................................................................32

3.5 Calibrating NMEA Depth, Speed and Water Temperature Data ......................................33

3.6 C-FORECAST Setup .......................................................................................................34

PACKING LIST...................................................................................................................A-1

OUTLINE DRAWINGS .......................................................................................................D-1

INTERCONNECTION DIAGRAM....................................................................................... S-1

Your Local Agent/DealerYour Local Agent/Dealer

9-52 Ashihara-cho,9-52 Ashihara-cho,

Nishinomi

a 662-8580, JAPANNishinomi

a 662-8580, JAPAN

Tele

hone :Tele

hone : 0798-65-21110798-65-2111

FaxFax 0798-65-42000798-65-4200

IRST EDITION :

IRST EDITION :AUGAUG.. 20042004

Printed in JapanPrinted in Japan

ll ri

hts reserved.

ll ri

hts reserved.

Pub. No.Pub. No. IME-44291-AIME-44291-A

00014914000

(( DAMIDAMI )) GP-7000FGP-7000F * 0 0 0 1 4 9 1 4 0 0 0 ** 0 0 0 1 4 9 1 4 0 0 0 *

IME

44291

IME

44291

IME

44291

IME

44291

* I M E 4 4 2 9 1 A 0 0 ** I M E 4 4 2 9 1 A 0 0 *

SAFETY INSTRUCTIONS

WARNING

ELECTRICAL SHOCK HAZARD

Do not open the equipment

unless totally familiar with

electrical circuits and

service manual.

Only qualified personnel

should work inside the

equipment.

Turn off the power at the switchboard

before beginning the installation.

Fire or electrical shock can result if the

power is left on.

CAUTION

Observe the following compass safe

distances to prevent interference to a

magnetic compass:

Use the power cable supplied with the

installation materials.

Use of other power cables may cause fire

or damage the equipment.

Use the proper fuse.

Use of the wrong fuse may damage the

equipment.

Observe the following precautions when

handling the transducer cable:

- Keep away from oils.

- Choose a working area where the

cable will not be damaged during

installation.

- Do not paint the cable.

The sheath of the cable is made of

chloroprene (or polyvinyl chloride).

Those materials easily deteriorate in

the presence of organic solvents

(toulene, etc.) found in paints. For

that reason keep the cable away from

ship's paint house.

Display

unit

Standard Steering

compass compass

0.70 m 0.45 m

SYSTEM CONFIGURATION

TRANSDUCER

Speed/Water

Temp Sensor

(option)

Distributor

MB-1000*

* Required when using

1 kW transducer.

Power Source

12-24 VDC

: Option

: Standard

: User Supply

ANTENNA UNIT GPA-017

DISPLAY UNIT

GP-7000F

How to remove the hard cover

Place your thumbs at the center

of the cover, and then lift the cover

while pressing it with your thumbs.

NMEA1 and NMEA2 ports:

Radar, autopilot, video sounder,

temperature indicator, etc.

PC/NMEA IN port:

PC, NMEA device, buzzer

iii

EQUIPMENT LISTS

Standard supply

Name Type Code No. Qty Remarks

Display Unit GP-7000F — 1

Antenna Unit

GPA-017

— 1

System also available

without antenna (for boats

which already have an

appropriate antenna)

Installation

Materials*

CP14-06400 000-041-183 1 Signal cable and power

cable

Spare Parts* SP14-03201 004-371-980 1

520-5PSD 000-015-204

525-5PWD 000-146-966

Transducer

520-5MSD 000-015-212

525ST-MSD 000-015-263Triducer

525ST-PWD 000-015-261

Choose

one

Also available without

transducer (for boats with

transducer already installed)

*: See list at back of this manual.

Optional equipment

Name Type Code No. Qty

GPS Antenna GPA-017S 000-040-541

CP20-01700 004-372-110 30 m, antenna cable extensionAntenna Cable Set

CP20-01710 004-372-120 50 m, antenna cable extension

Right Angle

Antenna Base No.13-QA330 000-803-239

L-angle Antenna

Base No.13-QA310 000-803-240

Antenna Base for

Rail Mounting No.13-RC5160 000-806-114

For mounting antenna unit

Mast Mounting Kit CP20-01111 004-365-780 For mounting antenna unit on a mast

MJ-A6SPF0012-050 000-134-424 6P – 6P, 5 m

MJ-A6SPF0012-100 000-133-817 6P – 6P, 10 m

MJ-A6SPF0003-050 000-117-603 6P, 5 m

Cable Assy.

MJ-A7SPF0007-050 000-144-418 7P, 5 m

50B-6 000-015-042

50B-6G 000-015-016

200B-5S 000-015-029

200B-5 000-015-027

Transducer

50/200-1T 000-015-170

Inner Hull Kit S 22S0191-2 000-802-598

Distributor MB-1000 000-040-809 For 1 kW transducer

02S4089 000-133-622 For Distributor MB-1000Cable Assy.

02S4147-0 000-141-082 For sensor

Sensor ST-02PSB 000-137-987

Sensor ST-02MSB 000-137-986

Speed/water temperature sensor

This page is intentionally left blank.

1. INSTALLATION

1.1 Display Unit

The display unit may be mounted on a desktop, overhead or flush mounted in a console.

Mounting considerations

Choose a mounting location for the display unit considering the following points:

• Choose a location where the controls can be easily operated.

• Leave sufficient space around the unit to facilitate checking and maintenance. See the

outline drawing at the back of this manual for recommended maintenance space.

• Locate the unit out of direct sunlight because of heat that can build up inside the cabinet.

• The operating temperature range is -15°C to 55°C (5°F to 131°F).

• Locate the unit well away from exhaust gases and other active gases.

• The location should be well ventilated.

• Choose a location where shock and vibration are minimal.

• Be sure the mounting location is strong enough to support the weight of the unit,

particularly in overhead mounting. If necessary reinforce the mounting location.

• A magnetic compass will be affected if the display unit is placed too close to the compass.

Observe the following compass safe distances to prevent deviation to the compass.

Standard compass, 0.70 m, Steering compass, 0.45 m.

Mounting

Desktop, overhead mounting

1. Fix the hanger to the mounting location with four self-tapping screws (5x20). See the

outline drawing on page D-1 for complete mounting dimensions.

2. Loosely screw the knob bolts into the display unit.

3. Set the display unit to the hanger and tighten the knob bolts.

4. Attach the hard cover to the display unit to protect the LCD.

FIXING HOLE

Unit: mm

Display unit, mounting dimensions for desktop or overhead mounting

Flush mounting

If the thickness of the console is 11-14 mm, use the washer

head screws (M4x20) supplied with the installation

materials. If it is thicker than those dimensions, the length of

the screws should be the thickness of the console plus

7.3 mm ±1.5 mm. The length of the threaded portion to be

inserted to the display unit should not exceed 7 mm (B≤7).

1. Prepare a cutout in the mounting location using the template provided.

2. Fix the display unit with six washer head screws (M4x20) provided.

52 80 150

Service

Clearance

Unit: mm

Mounting dimensions for flush mounting

A: Thickness of console

1.2 Antenna Unit

Refer to the antenna unit outline drawing at the back of this manual for mounting

instructions.

When selecting a mounting location consider the following points:

• Select a location out of the radar and Inmarsat beams. Those beams will obstruct or

prevent reception of the GPS satellite signal.

• There should be no interfering object within the line-of-sight to the satellites. Objects

within line-of-sight to a satellite, for example, a mast, may block reception or prolong

acquisition time.

• Locate the antenna well away from the antenna of a VHF radiotelephone to prevent

interference.

• Mount the antenna unit as high as possible. Mounting it this way keeps it free of

interfering objects and water spray, which can interrupt reception of GPS satellite signal if

the water freezes.

Note: If the antenna cable is to be passed through a hole in a bulkhead which is too small

to pass the connector, disassemble the connector with radio pincers and a monkey

wrench. After passing the cable through the hole assemble the connector as below.

Pin (Solder.)

Clamping Nut

Housing

Gasket

Washer

Shield

How to assemble the antenna connector

Andere Handbücher für GP-7000F

Inhaltsverzeichnis

Andere Furuno Marine-GPS-System Handbücher

Furuno

Furuno LC-90 Mark-II Bedienungsanleitung

Furuno

Furuno GP-1800 Bedienungsanleitung

Furuno

Furuno FELCOM 16 Bedienungsanleitung

Furuno

Furuno FELCOM 250 Bedienungsanleitung

Furuno

Furuno GP-80 Bedienungsanleitung

Furuno

Furuno GP-7000F Bedienungsanleitung

Furuno

Furuno GP-1871F Bedienungsanleitung

Furuno

Furuno Marine GPS System Bedienungsanleitung

Furuno

Furuno 2100 Technisches Handbuch

Furuno

Furuno GP-1610CF Bedienungsanleitung

Furuno

Furuno FMD3100 Bedienungsanleitung

Furuno

Furuno GP-1650WDF Bedienungsanleitung

Furuno

Furuno Precision PG-500 Bedienungsanleitung

Furuno

Furuno GP-3500F-D Bedienungsanleitung

Furuno

Furuno Navpilot 500 Handbuch

Furuno

Furuno SC-30 Betriebsanleitung

Furuno

Furuno ECDIS FEA-2100 Technisches Handbuch

Furuno

Furuno FELCOM 12 Bedienungsanleitung

Furuno

Furuno GP-1250 Bedienungsanleitung

Furuno

Furuno GP-70 Mark-2 Handbuch

Furuno

Furuno GD-1700C Bedienungsanleitung

Furuno

Furuno GP-1800F Bedienungsanleitung

Furuno

Furuno GD-3100 Bedienungsanleitung

Furuno

Furuno GP-32 Bedienungsanleitung

Beliebte Marine-GPS-System Handbücher anderer Marken

JRC

JRC JHS-183 Bedienungsanleitung

Thuraya

Thuraya IP Voyager Bedienungsanleitung

Raytheon

Raytheon NautoPilot NP 5100 Bedienungsanleitung

Garmin

Garmin GPSMAP 8008 MFD Bedienungsanleitung

Iridium

Iridium Pilot Bedienungsanleitung

Beam

Beam Terra 800 Bedienungsanleitung

Sailmon

Sailmon E4 Bedienungsanleitung

AUTOHELM

AUTOHELM ST50 PLUS Bedienungsanleitung

ASTRO

ASTRO X-5 twin B Bedienungsanleitung

Garmin

Garmin GPS 16 Series Referenzhandbuch

Iridium

Iridium EXTREME Bedienungsanleitung

Satcube

Satcube Ku Bedienungsanleitung

Thuraya

Thuraya ATLAS IP+ Bedienungsanleitung

Radio Zeeland DMP

Radio Zeeland DMP Sigma 120 Bedienungsanleitung

METRACKCO

METRACKCO SVT600/T1/T3 Bedienungsanleitung

Garmin

Garmin GPSMAP 190-01120-00 Bedienungsanleitung

Thuraya

Thuraya SatSleeve Bedienungsanleitung

Humminbird

Humminbird 532162-1_B Bedienungsanleitung