FuzzDog Enlightened Drive 2.0 Bedienungsanleitung

Enlightened Drive

v2.0

Highly Responsing verdrive

“Dumble-in-a-Box”!

No reproduction permitted without the express written

Schematic

B M

R1 2M2

R2 470K

R3 1K

R4 10K

R5 1K

R6 10K

R7 10K

R8 1K

R9 2K2 (CLR)

C1 470n

C2 100p

C3 100n

C4 3n3

C5 470n

C6 100u elec

C7 47 u elec

D1-3 BAT 41

Q1-2 2N7000**

IC *

GAIN 500KB

V ICE 10KB

T NE 50KB

V L 100KA

* riginals have been traced with AD712 and NE5532, both of which are still readily

available. No rules here - find the one you like the best. PA2604 are good, but you

may like a nice, simple 2262, 4558 or 072.

** ther FETs may work well, but original uses these.

Wiring shown overleaf will disconnect the battery when you remove the jack

plug from the input, and also when a DC plug is inserted.

Snap the little metal tag off the pots to mount them flush in the box.

You should use some kind of heat sink on the legs of the diodes when

soldering. They aren’t keen on heat. Any more than 3-4 seconds of iron

and they’re toast.

There are multiple pads for G D as well as pads for Jack-I and Jack-

OUT. These are used when combined with a Direct-Connect Daughterboard.

If you aren’t using a daughterboard just ignore J-I , JI, JO and J-OU, otherwise

please refer to the daughterboard document for more details.

The pads for the pots are spaced so

you can use vertical pots if you wish.

Why not try “Cheating Vericals” by

soldering snipped component legs to

the pots as shown left. You can just

wire them normally though.

1 2 3

Test the board!

Once you’ve finished the circuit it makes sense to test is before

starting on the switch and LED wiring. It’ll cut down

troubleshooting time in the long run. If the circuit works at this

stage, but it doesn’t once you wire up the switch - guess what?

You’ve probably made a mistake with the switch.

Solder some nice, long lengths of wire to the board connections

for 9V, G D, I and OUT. Connect I and OUT to the jacks as

shown. Connect all the G Ds together (twist them up and add a

small amount of solder to tack it). Connect the battery + lead to the

9V wire, same method. Plug in. Go!

If it works, crack on and do your switch wiring. If not... aw man.

At least you know the problem is with the circuit. Find out why, get

it working, THE worry about the switch etc.

BATTERY

IN OUT

Your nice, new circuit board

INCLUDING WIRED POTS!!!!

IN 9V GND OUT

Wire it up

(if using a daughterboard please refer to the relevant document)

The Board G D connections don’t all have to directly attach to the

board. You can run a couple of wires from the DC connector, one to the

board, another to the I jack, then daisy chain that over to the OUT jack.

It doesn’t matter how they all connect, as long as they do.

This circuit is standard, egative G D. Your power supply should be Tip

egative / Sleeve Positive. That’s the same as your standard pedals

(Boss etc), and you can safely daisy-chain your supply to this pedal.

ow... do some overdriven meditation!

PedalParts.co.uk

BOARD

OUT

BOARD

GND

BOARD

GND

BOARD

GND

BOARD

INPUT

BATTERY

OUT

BOARD

GND

BOARD

LED+

Drilling template

Hammond 1590B

60 x 111 x 31mm

Recommended drill sizes:

Pots 7mm

Jacks 10mm

Footswitch 12mm

DC Socket 12mm

Toggle Switch 6mm

This template is a rough guide only. You should ensure correct marking of your

enclosure before drilling. You use this template at your own risk.

Pedal Parts Ltd can accept no responsibility for incorrect drilling of enclosures.

It’s a good idea to drill

the holes for the pots

1mm bigger to give

yourself some wiggle

room, unless you’re a

drill ninja.

32mm

27mm

Inhaltsverzeichnis

Andere FuzzDog Zubehör für Musikinstrumente Handbücher

FuzzDog

FuzzDog Phase 45 Bedienungsanleitung

FuzzDog

FuzzDog Quack Machine Bedienungsanleitung

FuzzDog

FuzzDog Recurring Nightmare Bedienungsanleitung

FuzzDog

FuzzDog Stinky Cheese Bedienungsanleitung

FuzzDog

FuzzDog ToxicMinx V2 Bedienungsanleitung

FuzzDog

FuzzDog Blue Fool Bedienungsanleitung

FuzzDog

FuzzDog VERB V2 Bedienungsanleitung

FuzzDog

FuzzDog L'il Louie Bedienungsanleitung

FuzzDog

FuzzDog Vintage POW! Bedienungsanleitung

FuzzDog

FuzzDog MUFF GUN Bedienungsanleitung

FuzzDog

FuzzDog 3PDT Bedienungsanleitung

FuzzDog

FuzzDog QuagmireFuzz Bedienungsanleitung

FuzzDog

FuzzDog OVD-1 Bedienungsanleitung

Beliebte Zubehör für Musikinstrumente Handbücher anderer Marken

Behringer

Behringer AIRPLAY GUITAR AG10 Bedienungsanleitung

EMG

EMG SPC Bedienungsanleitung

FEURICH

FEURICH BASIC Bedienungsanleitung

thomann

thomann Harley Benton JA Bedienungsanleitung

NeoTech

NeoTech PAD-IT TUBA HARNESS Bedienungsanleitung

EMG

EMG X Series Service-Handbuch

Duncan

Duncan SH-8n Invader Kurzanleitung

Palmer

Palmer The Junction PDI-09 Bedienungsanleitung

EMG

EMG P Service-Handbuch

GuitarPCB

GuitarPCB Fuzzy Bee v2 Handbuch

Yamaha

Yamaha Tough-Terrain T-335 Bedienungsanleitung

EMG

EMG RT RIP TIDE Service-Handbuch

EMG

EMG EMG-91 ARCHTOP Service-Handbuch

LEWISMIDI

LEWISMIDI CZ Patch Library Bedienungsanleitung

Free The Tone

Free The Tone LB-2 Bedienungsanleitung

Duncan

Duncan Apollo Jazz Bass - neck Handbuch

dbx

dbx dB10 Bedienungsanleitung

EMG

EMG P-HZ Service-Handbuch