GAI-Tronics Titan Illuminated Crossing Telephone Bedienungsanleitung

Installation and User Guide

Titan Illuminated Crossing

Telephone

Titan Illuminated Crossing Telephone 1

CONTENTS

1Pre-Installation.........................................................................................3

1.1 Ringer Equivalence Number (REN) .................................................3

1.2 Suitability For Use ............................................................................4

1.3 Preparation.......................................................................................4

2INSTALLATION.......................................................................................5

2.1 Vertical Surface or Wall Mounting....................................................5

2.2 Pole Mounting...................................................................................8

2.3 Post Mounting...................................................................................9

2.4 Connections and Cabling ...............................................................10

3Approvals ............................................................................................11

Titan Illuminated Crossing Telephone 2

IMPORTANT

ALL POSSIBLE MEASURES MUST BE TAKEN TO ENSURE WATER,

FLUID OR DUST DOES NOT CONTAMINATE THE INTERNAL

COMPONENTS OF THIS TELEPHONE WHILST UNPACKING, PREPARING

AND INSTALLING IT IN INCLEMENT WEATHER CONDITIONS OR BY

NEGLIGENCE.

FAILURE TO CARRY OUT THIS BASIC FUNCTION

WILL INVALIDATE YOUR WARRANTY

Figure 1– Titan Illuminated Crossing Telephone at a glance

Titan Illuminated Crossing Telephone 3

1Product Description

The Crossing Telephone is a metal-bodied, weather resistant telephone

designed for connection to PETS. Features include:

•CB Operation only – lift handset to loop line – no dialling is possible.

•Illuminated legend panel and switch.

•Selectable illumination level setting.

•Selectable call timer

•Voltage free contacts, (N\C, N\O, COM) available on the terminal block,

which operate when the front panel button is pressed.

2Pre-Installation

The Crossing Telephone is connected by hard wiring -(unlike a standard indoor

telephone, which uses a plug and socket). Because of this, additional

requirements must be observed. Connection to the network (including via a

PBX/PABX) must be performed by authorised personnel with the agreement of

the network provider. Connections to the telephone should be isolated at the

network termination point (NTP) before opening the telephone case.

IMPORTANT

THE SAFETY OF THE USER/INSTALLER RELIES ON ISOLATION OF THE

TELEPHONE NETWORK AND NOT ON THE EARTHING OF THE CASE.

When connection is being made to privately owned extension wiring of a

PBX/PABX, then this should only be performed by either the network provider

to which the PBX/PABX may be linked, or by the authorised maintainer of the

PBX/PABX.

2.1 Ringer Equivalence Number (REN)

Exchange lines provide a limited amount of current to make telephones

connected to them ring correctly. In order to ensure that telephones will ring

properly, the number of instruments that may be connected to one line must be

controlled. All telephones are designated a Ringer Equivalence Number (REN)

- the Crossing Telephone has a REN of 1.

Note: Some PBX/PABX lines have different capabilities to the public network

and the Installation Handbook should be consulted for information.

When the Crossing Telephone is 3-wire connected with different models of

telephone, then full performance cannot be guaranteed.

Titan Illuminated Crossing Telephone 4

2.2 Suitability For Use

Crossing Telephones are suitable for connection to either loop disconnect or

multifrequency (tone) dialling telephone lines.

Connection may NOT be made to shared service (party) lines.

The telephone is NOT suitable for connection to a PABX which returns

secondary proceed indication

2.3 Preparation

Figure 2 – Circuit Board with Option Setting

2.3.1 Light Panel Current Selection

It is possible to give the legend panel and PRESS button illumination by wiring

the connections 1 and 2 together. A jumper is available to select, 5mA, or 1mA

of current from the line. The jumper is supplied in the 5mA position, (maximum

light output). For 1mA the jumper must be left off. It is advisable to select the

maximum current setting possible to give the best light output.

2.3.2 Timer Selection

Set the call time-out selector as required. If set to the ENABLE position, calls

will terminate after approximately 7 minutes even if the handset is still off hook.

Titan Illuminated Crossing Telephone 5

3INSTALLATION

IMPORTANT

All possible measures must be taken to ensure water or fluid does not

contaminate the internal components of the telephone whilst unpacking,

preparing and installing the telephone in inclement weather conditions or

by negligence.

Failure to carry out this basic function may invalidate your warranty and

Certification

As supplied the telephones are suitable for wall/vertical surface, pole or post

mounting.

If only one gland is used, the sealing plug should be left in place.

3.1Vertical Surface or Wall Mounting

As supplied, the telephone is only suitable for vertical surface mounting.

The following parts are included in the standard installation kit:

•2 - cable glands with sealing washers

•1 - 4mm socket wrench

1. Place the telephone on its rear surface on a firm horizontal surface.

2. Open the cover, release the front plate from the rear enclosure by

unscrewing the four captive screws using a 3mm socket wrench provided.

Figure 3 – Releasing the front plate

1. Remove the RED blanking plug from the cable entry hole leaving the

YELLOW plug in situ.

Titan Illuminated Crossing Telephone 6

Figure 4 – Gland fitting

2. Select the appropriate sized cable gland provided:

Use the smallest gland for cables diameters 4 - 7mm.

Use the largest gland for cable diameters 8 - 13mm.

Figure 5 – Threading the cable

3. Insert the selected gland into the threaded cable entry hole and tighten

using a 19mm A/F spanner, so that its sealing washer is compressed

against the enclosure surface.

Figure 6 – Tightening the gland

Using a suitable tool to create the mounting holes needed by punching through

the centre of the plastic flanged bushes fitted to the back wall of the rear

enclosure.

WARNING:.Your warranty will be invalidated if :-

1. Any fixing hole made in the rear enclosure is left unused.

2. Any additional holes are drilled into the telephone enclosure.

Titan Illuminated Crossing Telephone 7

Figure 7 – Knocking out plastic bushes

4. Ensuring that the cable entries are at the bottom, offer the rear enclosure up

to a vertical surface and mark through the punched holes. Do not use the

backplate as a template to drill the holes, work only from the marked

positions. Be careful not to damage the plastic washers.

⇒Drill the required number of holes in the vertical surface to the

appropriate depth to suit the best possible method of fixing.

5. Ensure that all four plastic flanged bushes are in place and the rear

enclosure is screwed tightly to the surface to prevent any water incursion

through the punched holes.

IMPORTANT:DO NOT use countersunk headed fixing screws. Only use

either round head, hexagon head or pan head screws provided.

Figure 8 – Plastic bush knockout

6. Insert the cable through the gland body and screw down the gland nut

sufficient to clamp the cable and make a seal.

Titan Illuminated Crossing Telephone 8

Figure 9 – Gland assembly

IMPORTANT: If only one gland entry is used, the blanking plug fitted to the

second gland position must be left in place.

3.2 Pole Mounting

Kit No 100-02-0208-001

For mounting telephones on to the side of round poles of 100mm to 200mm

diameter, or on to square or rectangular section uprights of 100mm to 150mm

across the mounting surface.

Banding straps (large-scale worm drive clamps) are not included in this kit and

must be obtained separately. For details of where these may be obtained call

GAI-Tronics.

For flat mounting on surfaces greater than 150mm across, use the Vertical

Surface or Wall Mounting method.

Figure 10 – Pole mounting

1. Disassemble the telephone as described in Vertical Surface or Wall

Mounting.

2. Punch through the flanged bushes in the rear enclosure - taking care to note

the IMPORTANT advice in Vertical Surface or Wall Mounting regarding

extra holes and warranty invalidation.

3. Attach the pole mounting clamp assemblies to the rear enclosure using the

M6 x 25 screws provided - see Figure 14 – Pole mounting.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere GAI-Tronics Telefon Handbücher

GAI-Tronics

GAI-Tronics 262-001 Bedienungsanleitung

GAI-Tronics

GAI-Tronics Commander GSM Betriebsanleitung

GAI-Tronics

GAI-Tronics KETS 1141 Bedienungsanleitung

GAI-Tronics

GAI-Tronics 491-204 Bedienungsanleitung

GAI-Tronics

GAI-Tronics 1090 Bedienungsanleitung

GAI-Tronics

GAI-Tronics 226-002 Bedienungsanleitung

GAI-Tronics

GAI-Tronics ILC-1117 Bedienungsanleitung

GAI-Tronics

GAI-Tronics 354-700 Bedienungsanleitung

GAI-Tronics

GAI-Tronics 263 Bedienungsanleitung

GAI-Tronics

GAI-Tronics 227-005 Bedienungsanleitung

GAI-Tronics

GAI-Tronics IPE2500A Betriebsanleitung

GAI-Tronics

GAI-Tronics 354-001 series Bedienungsanleitung

GAI-Tronics

GAI-Tronics Titan GSM Bedienungsanleitung

GAI-Tronics

GAI-Tronics Auteldac 5 Bedienungsanleitung

GAI-Tronics

GAI-Tronics 12576-502 Bedienungsanleitung

GAI-Tronics

GAI-Tronics 611C Referenzhandbuch

GAI-Tronics

GAI-Tronics Auteldac 4 Bedienungsanleitung

GAI-Tronics

GAI-Tronics 256S Bedienungsanleitung

GAI-Tronics

GAI-Tronics ITR1000-001 Betriebsanleitung

GAI-Tronics

GAI-Tronics 7265-101 Bedienungsanleitung

GAI-Tronics

GAI-Tronics Auteldac 4 VoIP Bedienungsanleitung

GAI-Tronics

GAI-Tronics 700 Series Bedienungsanleitung

GAI-Tronics

GAI-Tronics IDR1000A Betriebsanleitung

GAI-Tronics

GAI-Tronics 352-101 Bedienungsanleitung

Beliebte Telefon Handbücher anderer Marken

GE 2-9480 Bedienungsanleitung

Geemarc

Geemarc PHOTOPHONE 155 Bedienungsanleitung

Interquartz

Interquartz Gemini IQ333 Bedienungsanleitung

SSS Siedle

SSS Siedle HT 840-0 Bedienungsanleitung

Motorola

Motorola TITANIUM Bedienungsanleitung

Panasonic

Panasonic ICX Bedienungsanleitung

LG H870DS Bedienungsanleitung

Samsung

Samsung GT-I9500 Bedienungsanleitung

AT&T

AT&T Trimline 205 Bedienungsanleitung

Selta

Selta zenyth 600 Bedienungsanleitung

Doro

Doro AFTI 20 Bedienungsanleitung

UNIQCELL

UNIQCELL A1 Bedienungsanleitung

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Bedienungsanleitung

BT Decor 425 Bedienungsanleitung

NEC

NEC SV8500 Bedienungsanleitung

Teledex

Teledex PEARL Bedienungsanleitung

Ericsson

Ericsson Dialog 3213 Bedienungsanleitung

Yealink

Yealink VP530 Bedienungsanleitung