Galvin Engineering 656512 Merkblatt

Product Installation Guidelines

Version 1, 6th July 2022, Page 1of 5

SS Vandal Resistant D/F Plate Assembly

for Pneumatic Inwall Cistern w/ CP BS

Raised Buttons

PRODUCT CODES

- 656512

SPECIFICATIONS

−Face plate assembly features pneumatic dual flush push activation buttons for CIST19-PNEU-2 Slim-

Line Inwall Cistern.

−2mm thick, Vandal resistant stainless steel faceplate.

TECHNICAL DATA

Activation

Push Button

Connections

Pneumatic

Hose Length

3 metres

Finish

Polished

NOTE: Galvin Engineering continually strive to improve their products. Specifications may change without

notice.

MOUNTING DETAILS

If a cut out is required, refer to the face plate position and cut out details below.

- The push button can be positioned as preferred but consideration should be given to ensure it is easily

accessible for children and adults.

- A 70mm x 140mm x 80mm cut out is required in the wall to fit the two push buttons. Drill two holes 160

mm from centres as shown for two nylon wall plugs 8 X 40 (NWP8).

Product Installation Guidelines

Version 1, 6th July 2022, Page 2of 5

DIMENSIONS

Product Installation Guidelines

Version 1, 6th July 2022, Page 3of 5

INSTALLATION

INSTALLATION COMPLIANCE: Galvin Engineering products must be installed in accordance with these

installation instructions and in accordance with your local regulatory requirements. Water and/or electrical supply

conditions must also comply to the applicable national and/or state standards. Failing to comply with these

provisions shall void the product warranty and may affect the performance of the product.

Assemble the push buttons and faceplate.

- Insert the pneumatic push buttons into the

faceplate and fasten together using hex nuts.

- Ensure the rubber washers are placed in

between the faceplate and the hex nuts.

Connect the pneumatic tubes to the push

buttons.

- Connect one end of the air tube to the push

button and the other end to the cistern.

- Ensure the tube is connected to the correct

button (half or full flush).

- Check if the connections are tight and secure.

- Check if both buttons are operational and

check the air tubes for leaks

Product Installation Guidelines

Version 1, 6th July 2022, Page 4of 5

Mount the faceplate.

- Install nylon wall plugs as shown.

- Apply a thin bead of silicon on the edge of cut out

- Mount the faceplate to the wall using the two

countersunk torx screws.

- Ensure the screws are securely tightened and

the faceplate is mounted flush to the wall.

Check for correct operation.

Product Installation Guidelines

Version 1, 6th July 2022, Page 5of 5

WARRANTY

The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty

Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied.

Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including

but not limited to the implied warranties of merchantability and fitness for a particular purpose.

Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download

from www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free

from operational defects in workmanship and materials for the warranty period as shown on the schedule in

the manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any

defective products manufactured by Galvin Engineering without charge, so long as the terms of the

Manufacturer’s warranty are complied with.

The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy

for breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or

consequential damages, including without limitation, lost profits or the cost of repairing or replacing other

property which is damaged if this product does not work properly, other costs resulting from labour charges,

delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,

chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty

shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or

alteration of the product.

TROUBLESHOOTING

PROBLEM

CAUSE

RECTIFICATION

Cistern does not flush

No air supplied from air pump

Check air tube for leaks

Replace air pump if damaged

Faulty Push Button

Replace damaged push button

Incorrect connections

Check all connections

NON-SERVICEABLE PRODUCTS INFORMATION

Push Button, Air Pump, Face Plate

These items are non-serviceable products. If damaged, they must be replaced.

If there appears to be any problems with these items, please contact Galvin Engineering.

Note: Before attempting to replace any of these items check that you have access to re-run the

connection leads. If you do not have access or you have any doubts, please contact Galvin Engineering

for advice before commencing replacement.

Inhaltsverzeichnis

Andere Galvin Engineering Sanitärprodukte Handbücher

Galvin Engineering

Galvin Engineering CliniLever TCBTC80CC Bedienungsanleitung

Galvin Engineering

Galvin Engineering GalvinCare CP-BS Merkblatt

Galvin Engineering

Galvin Engineering CliniLever TCWMC80CC Merkblatt

Galvin Engineering

Galvin Engineering Ezy-Drink 85326X Merkblatt

Galvin Engineering

Galvin Engineering Ezy-Drink CP Lead Safe 2 in 1 Bottle Filler & Bubbler Hob... Merkblatt

Galvin Engineering

Galvin Engineering CliniMix Lead Safe 100.00.71.00 Merkblatt

Galvin Engineering

Galvin Engineering Assist 41978CP Merkblatt

Galvin Engineering

Galvin Engineering Haws GalvinSafe Axion 8100-A Merkblatt

Galvin Engineering

Galvin Engineering 49920 Bedienungsanleitung

Galvin Engineering

Galvin Engineering Ezy-Drink Lead Safe 170.81.13.01 Merkblatt

Galvin Engineering

Galvin Engineering CliniLever TCWSC150C Merkblatt

Galvin Engineering

Galvin Engineering Ezy-Wash TF81HJS Merkblatt

Galvin Engineering

Galvin Engineering GalvinSafe 190.80.10.12 Merkblatt

Galvin Engineering

Galvin Engineering GalvinSafe 190.42.11.90 Merkblatt

Galvin Engineering

Galvin Engineering Ezy-Drink Lead Safe 170.50.14.00 Bedienungsanleitung

Galvin Engineering

Galvin Engineering GalvinSafe 190.41.12.12 Merkblatt

Galvin Engineering

Galvin Engineering TCWBC150C Bedienungsanleitung

Galvin Engineering

Galvin Engineering GalvinSafe 190.42.11.12 Merkblatt

Galvin Engineering

Galvin Engineering Haws SP220SS Merkblatt

Galvin Engineering

Galvin Engineering Ezy-Drink TD25XEB Bedienungsanleitung

Galvin Engineering

Galvin Engineering Safe-Cell 50150 Merkblatt

Galvin Engineering

Galvin Engineering Ezy-Drink 316 TDBFXEB Merkblatt

Galvin Engineering

Galvin Engineering CliniMix WM-PMSKIT Merkblatt

Galvin Engineering

Galvin Engineering CliniMix CP-BS Merkblatt

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

Kohler

Kohler K-6228 Montageanleitung

UBERHAUS DESIGN

UBERHAUS DESIGN 75175017 Bedienungsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Fortis

Fortis MILANO 78211JS Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Moen

Moen 5922 Series Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung