Gamma+ 8800 Els Bedienungsanleitung

OWNER'S MANUAL

Issue 1 - June 2006

STRINGING MACHINE

8800 Els

6 POINT MOUNTING

LIMITED WARRANTY

GAMMA SPORTS warrants to the original purchaser that the 8800 Els stringing machine ("EQUIPMENT") purchased is free

fromdefectsinmaterialsandworkmanshipforaperiodoffive(5)yearsfromthedateoforiginalpurchaseformechanicalparts

(excluding electrical parts and string clamps), and for a period of one (1) year from the date of purchase for all electrical parts

and string clamps. Should any defects develop under normal use within the specified time periods, GAMMA will at its option,

repair or replace the defective EQUIPMENT provided it is returned to GAMMA prepaid at the purchaser's expense. This

warranty does not apply to any damage or defect caused by negligence, abuse, misuse, unauthorized alteration, shipping,

handling, or part wear and tear as a result of normal use.

Routine maintenance, adjustment, and cleaning required to ensure proper operation are the responsibility of the purchaser

and are not covered under the terms of this warranty. These include, but are not limited to: String Clamp adjustment, as

described on page 18, Switch Action Clamp Base adjustment, as described on page 18, and the cleaning procedures listed

on page 19.

GAMMA’sobligationunderthiswarrantyislimitedtorepairorreplacementofdefectiveEQUIPMENT,andnooneisauthorizedto

promiseanyotherliability.GAMMAshallinnoeventbeliableforanyincidentalorconsequentialdamages.

ToreturndefectiveEQUIPMENT,areturnauthorization(RA#)mustbeobtainedfromaGAMMAcustomerservicerepresentative.The

RA#mustbemarkedontheoutsideoftheshippingcartonbeingreturned.Allreturnsmustbeshippedprepaidbythecustomer

to GAMMA. Please retain the original shipping carton and packing materials for any future shipments. GAMMA will not be

responsible for machines which are not sent in the original undamaged packaging.

TABLE OF CONTENTS

PAGE 1................................................................................................ WARRANTY

PAGE 2................................................................................................. FEATURES

PAGE 3....................................................................... UNPACKING & ASSEMBLY

PAGE 8..................................................... POWER CONNECTION & CONTROLS

PAGE 10.................................................. TENSIONER & GRIPPER OPERATION

PAGE 11......................................................................... MOUNTING THE FRAME

PAGE 13.........................................................................STRINGING THE FRAME

PAGE 15................................................. STRING LENGTH METER OPERATION

PAGE 16.........................................................................ADDITIONAL FEATURES

PAGE 17...............................MAINTENANCE, ADJUSTMENTS & CALIBRATION

PAGE 19..................................................................... TROUBLESHOOTING TIPS

PAGE 20...................................................................................PATHFINDER AWL

PAGE 21..............................................................................................PARTS LIST

PAGE 22....................................................................................PARTS DRAWING

OWNER'S MANUAL

8800 Els

MACHINE FEATURES

Electric Constant Pull Tensioner w/ 11 lb. to 89 lb. Tension

Range

Digital Tension Setting Display

Professional Six Point Self-Centering “Suspension Mount”

Racquet Mounting System - Accomodates All Racquets

Without Adapters

Parallel Jaw Linear Gripper w/ Diamond Dust Coated Gripping

Surfaces

Professional Dual Action, Rotating, Diamond Dust Coated,

Fixed String Clamps

High Strength Extruded Aluminum Frame with Durable

Anodized Finish and 2-Convenient Padded Tool Trays

Unique Internal Drawer System for Storing Tools and Adap-

tors.

Convenient Foot Actuated Tensioner Switch

GAMMA 8800 Els

FEATURES

8800 Els

Unpacking Instructions & Contents

Instructions for Unpacking and Preparing for Assembly

The stringing machine is shipped in three cartons, a large carton for the stringing machine

and accessories, a medium carton for the turntable and mounting system and a smaller

carton for the post and base legs. Please save the cartons and packing materials for

possible shipments in the future. Gamma Sports cannot be responsible for machines

that are not returned, shipped in their original, undamaged packaging. The tools you will

need to assemble the machine are provided with the machine. Due to the weight of the

tensioner unit, you may need the assistance of someone to help lift the tensioner unit out of

the carton.

Once the cartons are opened, remove all inner cartons and check to be sure that all parts

are present and accounted for.

Contents of Base & Leg Carton

(1) Lower Post

(1) Upper Post with Flange Plate

(4) Legs

(1) Locking Knob Screw

(4) M8 x 25 Flat Head Screws

(4) M8 x 30 Cap Screws

(1) M8 x 25 Cap Screws for Height Adjustment

(1) String Reel Holder (M8 Threaded Pin), (1) Knob, (10) Spacers, & (2) M8 Washers

Contents of Mounting System Carton

(1)Turntable

(2) Mounting Stands w/ Frame Support Slide, Side Supports, and Adapters

(2) String Clamp Heads

(1) Package of Spare plastic adapters for mounting system supports (contains 16 pcs)

Contents of Large Master Carton (including accessory cartons packed inside)

(1) StringerAssembly Unit w/ Tensioner Module

(1) Power Cord

(1) Foot Pedal Tensioner Switch

(1) Tool Kit (contains side cutter, bent nose pliers, needle nose pliers)

(1) Straight Stringers Awl & (1) Pathfinder Specialty Awl

(1)Tools for assembly and maintenance

Base Leg Assembly

The stringing machine uses a four leg base

design. The legs must be assembled to the

support post before use. Remove the lower

column support, the upper column support,

four (4) legs, four (4) socket head cap

screws and four (4) flat head cap screws

from the small shipping carton.

Base Leg Assembly (Cont.)

Align the holes in the leg flange with the

matching holes in the lower column support

post. Secure the leg with one FLAT HEAD

cap screw through the upper hole, and one

SOCKET HEAD cap screw through the bot-

tomhole.Repeatthisprocedureforthethree

remaining legs.

ASSEMBLY INSTRUCTIONS

Base Leg Assembly (Cont.)

To complete the base stand, screw the height adjust-

ment locking knob (“A”) into the side of the support

column. The locking knob should not protrude beyond

the inside of the support column at this time.

“A”

ASSEMBLY INSTRUCTIONS

Height Adjustment

Theheightofthe machineisadjustablefrom

39”to46”.Tochange theheight, removethe

socket head cap screw from its current posi-

tionandplaceitintheappropriateholetoset

the desired height of the machine.

Stand Upper Post Installation (cont.)

Securetheflangetothebasewiththesixcap

screws or the rubber feet.

USE CAUTION WHEN SECURING

SCREWSTO SLIDING BRACKETS, THEY

WILL STRIP.

Stand Upper Post Installation

Withthe height adjustmentcap screw onthe

upper post facing the brake lever & string

lengthmeter,align the 6 holes marked “X” in

the upper post flange with the holes in the

slide brackets of the machine base.

STRING REEL HOLDER INSTALLATION

Thestringreelholder pinisan8 mmrodwith

threads on both ends, and flat surfaces

machinedon one end.Thread theendof the

pinwithouttheflatsurfacesintothethreaded

boss on the right side of the lower column

support. Using the M6 open end wrench

positioned on the flat surfaces, securely

tighten the pin to the lower column support.

The string reel holder can hold up to 5 reels

of string (depending on the size of the string

reel). Before placing the first reel on the pin,

slide two M8 washers over the pin and slide

them to the boss on the lower column sup-

port.Afterthe firstreelis placedontothepin,

place two spacers between each reel to

provide enough space between reels and

allow them to turn freely without rubbing

against one another. (To provide a smooth

feed to the String Length Meter, place the

reels on the pin so the string spools off the

reel from the underside of the reel.)

After the last reel is installed, place the

remaining spacer(s) on the pin and attach

the threaded knob to the end of the pin.

ASSEMBLY INSTRUCTIONS

String Clamp Installation

The post of the string clamp and tube of the string

clamp base are treated with grease to provide protec-

tion against corrosion during shipping. Remove any

excessive grease with a clean cloth prior to use. The

post and tube may also be cleaned with isopropyl

alcohol. After this type of thorough cleaning, the post

and tube should be treated with a light coating of

machine oil to protect the surfaces against corrosion

and to ensure smooth operation.

Turntable and Mounting System In-

stallation

To install the turntable remove the four nuts

underneath holding the mounting bolts in

place. Align the bolts with the holes in the

turntablepin. Securethemwiththeincluded

allen wrech.

NOTE: Apply the turntable brake and it will

be easier to align the bolts and holes.

POWER CONNECTION & CONTROLS

Front Panel Features

A - String Gripper

B - Tension Button

C - L.E.D.Tension Display

D - ControlPanel

Back Panel Features

A - 115 / 230 Volt Switch

B - Lighted Power Switch

C - A/C Power Cord Socket

D - String Length Meter Receptacle

E - 2 Amp Fuse Holder (w/ spare fuse)

F - 2 Pin Foot Pedal Switch Receptacle

Instructions for Power Connection and Controls

CAUTION ! Before connecting to the power supply, check the voltage source

that the machine is being connected to. The acceptable range of input volt-

ages for this machine is between 100 V and 110 V @ 50 to 60 Hz. If you have any

questions regarding the input voltage supply for your area, please ask your electric

utility company.

To install the power cord, insert the female end of the power cord into the Power Cord

Socket located on the back panel and plug the male end into a grounded power outlet.

When using extension cords, use grounded heavy duty extension cords rated for 15

AMP service. To connect the foot pedal switch, insert the 2 pin female connector located at

the end of the foot pedal switch cord, into the two pin receptacle located in the back panel.

Tighten the connector with the sleeve nut located on the foot pedal switch connector.

After checking to be certain that the machine is connected to the correct input voltage,

switch on the machine by pressing the Lighted On-Off Power Switch on the side panel. At

start-up, the LED will display a countdown from “9.0” to “0.0” while the machine performs a

self diagnostics check at start-up.

WARNING! FOR INDOOR USE ONLY. TO BE USED

BYADULTSORUNDERADULT SUPERVISIONONLY.

NEVEROPENUNITWITHPOWERCONNECTED

CONTROL PANEL FUNCTIONSAND

FEATURES

Single Digit (0-4)

Memory LED Display Three Digit (XX.X) Tension Settings or

String Length LED Display

Keypad - Used to enter

tension settings

Release Button - Returns gripper to

starting position and releases tension

Lbs/Kgs Button - Changes tension

display from Lbs to Kgs. Each press of

the button toggles back and forth

between Lbs and Kgs

Speed Button - Changes pulling speed

of winder from Fast to Slow. Slow speed

is recommended for low stretch strings,

such as Kevlar. Each press of the

button toggles back and forth between

Fast and Slow speed.

Pre-Stretch Function - Pulls string

10% or 20% over the tension setting (up

to 90 lbs / 40.8 kgs), releases the string,

and repulls to the tension setting. Each

press of the button toggles between

10%, 20% or no pre-stretch.

String Length Meter Button - Enables

string length meter function. Each press

of the button toggles back and forth

between Meters and Feet measure-

ment. To switch back to tensioning

function, press the “Lbs/Kgs” button.

Clear Button - Clears display to enter a

new tension

Knot Function - Increases pulling tension

by 10% over the setting value (max 90 lbs /

40.8 kgs) for one pull. During pull the

Memory LED flashes to indicate that the

Knot function is enabled.

Tension Index Buttons - Changes

tension setting in +/- 1.0 or 0.1 Lb or Kg

increments. Holding the button down

will scroll the tension setting values up

or down. Tension settings entered with

the tension index buttons are placed

into temporary memory setting “0”.

Memory Button - Indexes from 4 preset

tension settings that can be stored in

memory. Settings are retained even if

machine is turned off. Each press of the

button indexes to the next memory setting.

Memory settings 1-4 must be entered using

the keypad followed by pressing the “ENT”

button.

Enter Button - Confirms tension setting

when entered on keypad (display flashes

when tensions are keyed in with the keypad

until this button is pressed)

Test Function - Performs internal

calibration check. Press and hold for 5

seconds until the winder reverses and

performs an internal diagnostic check,

such as the one performed at start-up.

Andere Handbücher für 8800 Els

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Gamma+ Besaitungsmaschine Handbücher

Gamma+

Gamma+ 6900 Els Bedienungsanleitung

Gamma+

Gamma+ X-ST Bedienungsanleitung

Gamma+

Gamma+ 7500 Els Bedienungsanleitung

Gamma+

Gamma+ X-Stringer Bedienungsanleitung

Gamma+

Gamma+ PROGRESSION 600ES-LED Bedienungsanleitung

Gamma+

Gamma+ Progression ES II Bedienungsanleitung

Gamma+

Gamma+ 9900 Els Bedienungsanleitung

Gamma+

Gamma+ PROGRESSION 602 Bedienungsanleitung

Gamma+

Gamma+ X-ES Bedienungsanleitung

Gamma+

Gamma+ Progression Els Bedienungsanleitung

Gamma+

Gamma+ X-6 Bedienungsanleitung

Gamma+

Gamma+ Progression 602 FC Bedienungsanleitung

Gamma+

Gamma+ 5800 Els Bedienungsanleitung

Gamma+

Gamma+ Progression 200 Bedienungsanleitung

Gamma+

Gamma+ 6500 Els Bedienungsanleitung

Gamma+

Gamma+ Progression ES II+ Bedienungsanleitung

Gamma+

Gamma+ Progression STII Bedienungsanleitung

Gamma+

Gamma+ PRO 100 Bedienungsanleitung

Gamma+

Gamma+ PROGRESSION ST Bedienungsanleitung

Gamma+

Gamma+ X-6FC Bedienungsanleitung

Gamma+

Gamma+ Progression 600 Bedienungsanleitung

Gamma+

Gamma+ 6004 Bedienungsanleitung

Gamma+

Gamma+ 7900 Els Bedienungsanleitung

Gamma+

Gamma+ X-2 Bedienungsanleitung

Beliebte Besaitungsmaschine Handbücher anderer Marken

Spinfire

Spinfire Flame Bedienungsanleitung

Babolat

Babolat STAR 5 Bedienungsanleitung

TSE

TSE PTV100/72 Bedienungsanleitung

Prince

Prince 7000 Bedienungsanleitung

PREMIUM STRINGER

PREMIUM STRINGER 9200 Bedienungsanleitung

Gamma Sports

Gamma Sports 602FC Bedienungsanleitung

Atlas

Atlas 8600 Bedienungsanleitung

Wilson Electronics

Wilson Electronics BAIARDO Bedienungsanleitung

Stringway

Stringway MS140N Bedienungsanleitung

Gamma Sports

Gamma Sports STII Bedienungsanleitung

Babolat

Babolat Sensor Mono Bedienungsanleitung

Babolat

Babolat SENSOR EXPERT Bedienungsanleitung

Yamaha

Yamaha Strings SS-30 Bedienungsanleitung

Hornet

Hornet PRO'S PRO Bedienungsanleitung

ATS

ATS Super Stringer II Bedienungsanleitung

Gamma Sports

Gamma Sports Els Bedienungsanleitung

PENTA

PENTA Premium Stringer 7600 Bedienungsanleitung

power tennis nederland

power tennis nederland P501 Bedienungsanleitung