Gamma+ X-2 Bedienungsanleitung

OWNER'SMANUWNER'SMANU

WNER'SMANUWNER'SMANU

WNER'SMANUALAL

ALAL

Issue1-December2003Issue1-December2003

Issue1-December2003

Provided by www.gssalliance.com

OWNER'SMANUAL

LIMITEDLIFETIMEWARRANTYLIMITEDLIFETIMEWARRANTY

LIMITEDLIFETIMEWARRANTY

GAMMA warrants to the original purchaser that the GAMMA X-2 stringing machine ("EQUIPMENT") purchased is free from

defectsinmaterialsandworkmanship forthelife oftheEQUIPMENT. Should anydefectsdevelop undernormaluse, GAMMA

will at its option, repair or replace the defective EQUIPMENT provided it is returned to GAMMA prepaid at the purchaser's

expense. This warranty does not apply to any damage or defect caused by negligence, abuse, misuse, unauthorized

alteration, shipping, handling, or part wear and tear as a result of normal use.

GAMMA'sobligationunderthiswarrantyislimitedtorepairorreplacementofdefectiveEQUIPMENT,andnooneisauthorized

to promise any other liability. GAMMA shall in no event be liable for any incidental or consequential damages.

To return defective EQUIPMENT, a return authorization (RA#) must be obtained from an GAMMA customer service

representative by calling 1-800-333-0337. The RA# must be marked on the outside of the shipping carton being returned. All

returnsmustbeshipped prepaid bythecustomertoGAMMA.Please retain theoriginalshippingcartonandpacking materials

for any future shipments.

TABLEOFCONTENTSTABLEOFCONTENTS

TABLEOFCONTENTS

PAGE1 ............................................................................................WARRANTY

PAGE2 .....................................................................ASSEMBLYINSTRUCTIONS

PAGE4 ..................................................................... MOUNTINGTHERACQUET

PAGE5 ..........................................................................STRINGINGTHEFRAME

PAGE8 .................................................................................. PATHFINDERAWL

PAGE9 ............................................................................................PARTSLIST

PAGE10 ....................................................................... EXPLODEDPARTSVIEW

ASSEMBLYINSTRUCTIONS

Installing the Turntable

Placetheturntableringspaceronthepostof

the turntable.

Inserttheturntablecenterpostintothebush-

ing assembly of the machine base.

Installing the Support posts

Slide each support post onto the end of the

turntable bar. The posts should be oriented so

astoangleawayfromtheturntablecenterpost.

Installing the Drop Weight

Remove the endcap from the tension bar

and slide the drop weight onto the bar. The

weight should be oriented with the knob end

closest to the string winder. Replace the

endcap.

ASSEMBLYINSTRUCTIONS

Clamp Adjustment

The floating clamps provided with your ma-

chinewillneedminoradjustmentsaccording

to what string type, construction, and gauge

you are using.

If the strings slip through the jaws of the

clamp, tighten the clamp by turning the

thumb knob opposite of the handle, in the

clockwise direction. If the clamps leave im-

pressions or damage the string, they are too

tight and the thumbwheel must be turned

counterclockwise.

The clamp jaws must be clean and free from

dirt, oil, and any string coating for them to

grip properly. Keep the clamp jaws clean

with alcohol.

Clamp Adjustment

Thumb Knob

Tension Bar Stop Screw

Raise the Tension Bar to an upright position.

Using the supplied 5MM wrench, securely

tighten the Stop Screw. This will prevent the

Tensionbarfromcontactingtheracquetframe.

Winder Support Stand Installation

Attach the winder support stand to the ma-

chine base using the 5MM hex key (in-

cluded) by sliding the 2 brackets into the 2

rear most grooves. Then align the right side

of the stand with the right end of the base.

MOUNTINGTHERACQUET

Installing the Racquet Support Adapters

The GAMMA X-2 is supplied with two styles

of RacquetSupportAdapters.Athickprofile

adapter for widebody racquets and a thin

profile adapter for conventional racquet

frames. The Adapters are also tapered, use

the highest side of the adapter that does not

interfere with the string grommet holes.

Adjusting the Frame Support Posts

Place the racquet frame over the center

posts and onto the frame support posts.

Loosen the locking screws on one support

post and slide the post in the appropriate

direction until the plastic adapter contacts

the frame. Securely tighten the locking

screws.Adjustthe oppositepostinthesame

manner.

It is extremely important both plastic adapt-

ers are in contact with the frame to prevent

racquet damage.

Securing the Racquet

With the frame support posts properly ad-

justed, place the frame hold down plates

overthecenterscrewsandtightentheclamp

bar knobs securely. Do not overtighten the

knobs as frame damage may occur.

Note: Inverted throat racquet frames may

require the throat clamp plate to be rotated

180 degrees to match the frame.

STRINGINGTHEFRAME

Setting Tension

The drop weight is of a two piece design.

When assembled, it will accomodate ten-

sionsfrom20lbs.to90lbs.Fortensionsfrom

8to20 lbs.,removethe5mmbolt ontheface

of the drop weight, and use the smaller

portion of the weight as described above.

Note: Tensions above 77lbs. require re-

moval of the drop weight bar endcap.

To set the stringing tension, loosen the lock-

ingknobon the sideofthedropweight.Slide

the weight in the appropriate direction until

the face closest to the string gripper is

indexedwiththedesiredtensionmarkonthe

tension bar.

Starting the Main Strings

Tobeginstringingthemainstrings,countthe

number of holes at the throat of the frame,

which will determine the starting point. For

racquets with 4 or 8 holes at the throat, the

main strings will begin at the head. For

racquets with 2 or 6 holes at the throat, the

main strings will begin at the throat.

Threadthetwoendsofthestringthroughthe

two center grommet holes at the head or

throat as determined in the previous step.

Route the strings through the opposite center holes.

STRINGINGTHEFRAME

Clamping the First Main String

Thread one end of the string through the

adjacent grommet hole and pull excess by

hand. Clamp both the center and the adja-

cent string to each other on the inside of the

frame.

Pulling Tension

Wrap the free string clockwise around the

gripper drum once and position between the

gripper jaw.

Gently turn the gripper clockwise while

squeezing the jaws together until all slack in

the string is removed.

Note:Forproperoperation,thestringgripper

jaw must be in the position shown. The

tension in the string provides the clamping

force to the jaws.

While holding the string gripper drum with

your hand, lift the tension bar to approx. 45

degree angle and let fall. If the tension bar

drops below horizontal, repeat the above

action until the bar comes to rest parallel to

the racquet. The set tension will be reached

when the bar rests horizontal.

If the bar comes to rest above horizontal,

release the string and re-pull tension.

Manually forcing the bar into the horizontal

position will greatly increase string tension

and may result in racquet damage.

STRINGINGTHEFRAME

Clamping the String

Clamp the tensioned string to the next adja-

cent string using the secong string clamp.

Release the tensioned string by raising the

tension arm.

Repeattheprocedureforalloftheremaining

main strings and tie off following the racquet

manufacturers recommendations.

Starting the Cross Strings

Follow the manufacturer's recommended

stringing pattern for one or two piece string-

ing. This will determine the starting point for

the cross strings. Weave the first two cross

strings and pull tension and clamp the cross

strings to each other.

Finishing the String Job

Weave and tension the remaining cross

strings and tie off at the specified grommet

hole.

RemovethestrungracquetfromtheGAMMA

X-2 in the reverse order of mounting.

PATHFINDERAWL

The GAMMA X-2 includes the Pathfinder

stringing awl which creates a pathway be-

tween or around strings to make inserting a

string through tight grommets easier and

quicker.

Insert the awl through the grommet hole in

the same manner as for traditional awls.

The Pathfinder awl must be in the closed

position before insertion.

Once the awl is inserted, pull the handle of

theawloutwardwhile holding the tip section

in place, leaving the outer sheath in the

grommet hole.

Insert the end of the string into the center of

the sheath.

While holding pressure on the string, slowly

pull the sheath out of the grommet hole to

leave the end of the string exposed.

PARTSLIST

PART #

25A

30A

MRSG

MPFC

DESCRIPTION

TURNTABLE BUSHING

BUSHING SET SCREW

KNOB

TENSION BAR

SET SCREW

TENSION BAR CAP

DROP WEIGHT KNOB

FRONT WEIGHT

BACK WEIGHT

TENSION BAR DRUM

SET SCREW

STRING GRIPPER DRUM

ROTATIONAL GRIPPER

RATCHET TEETH

RACHET TEETH SPRING

CAP SCREW

FLOATING CLAMP ASMBLY

LEVER JAW

INNER JAW

KNOB JAW

LEVER

KNOB

SWING BOLT

RETURN SPRING

PIVOT PIN

RETAINING RING

PART #

82A

83A

161

162

163

255

256

257

258

259

108

109

98A

260

DESCRIPTION

CLAMP PLATE

CLAMP PLATE PAD

FRM. SUPP. ADPTR - SHORT

FRM.SUPP. ADPTR. - TALL

TENSION BAR STOP SCREW

TURNTABLE

SUPPORT POST

SUPPORT POST PIN

SUPPORT POST PAD

WINDER BEARING

GRIPPER PIVOT PIN

PIVOT PIN RET. COLLAR

BASE

BASE FOOT

LOWER WINDER STAND

UPPER WINDER STAND

WINDER ST. BRACKET CLAMP

( NOT SHOWN )

HEX WRENCH / 3MM

HEX WRENCH / 5MM

5MM T-HANDLE HEX WRENCH

PATHFINDER AWL

STRINGERS AWL

UTILITY KNIFE

NEEDLE NOSE PLIERS

10MM WRENCH

TURNTABLE SPACER RING

Inhaltsverzeichnis

Andere Gamma+ Besaitungsmaschine Handbücher

Gamma+

Gamma+ Progression Els Bedienungsanleitung

Gamma+

Gamma+ 7000 Es Bedienungsanleitung

Gamma+

Gamma+ Progression 600 Bedienungsanleitung

Gamma+

Gamma+ Progression ES II Bedienungsanleitung

Gamma+

Gamma+ Progression Els Bedienungsanleitung

Gamma+

Gamma+ 8800 Els Bedienungsanleitung

Gamma+

Gamma+ PRO 100 Bedienungsanleitung

Gamma+

Gamma+ X-Stringer Bedienungsanleitung

Gamma+

Gamma+ 7900 Els Bedienungsanleitung

Gamma+

Gamma+ 5003 Bedienungsanleitung

Gamma+

Gamma+ 5800 Els Bedienungsanleitung

Gamma+

Gamma+ X-6FC Bedienungsanleitung

Gamma+

Gamma+ Progression ES II+ Bedienungsanleitung

Gamma+

Gamma+ 6900 Els Bedienungsanleitung

Gamma+

Gamma+ 6004 Bedienungsanleitung

Gamma+

Gamma+ X-ST Bedienungsanleitung

Gamma+

Gamma+ 5003 Bedienungsanleitung

Gamma+

Gamma+ Progression Els Bedienungsanleitung

Gamma+

Gamma+ 5002 Bedienungsanleitung

Gamma+

Gamma+ X-ST Bedienungsanleitung

Gamma+

Gamma+ PROGRESSION 602 Bedienungsanleitung

Gamma+

Gamma+ Progression 602 FC Bedienungsanleitung

Gamma+

Gamma+ Progression 602 FC Bedienungsanleitung

Gamma+

Gamma+ X-6 Bedienungsanleitung

Beliebte Besaitungsmaschine Handbücher anderer Marken

Spinfire

Spinfire Flame Bedienungsanleitung

Babolat

Babolat STAR 5 Bedienungsanleitung

TSE

TSE PTV100/72 Bedienungsanleitung

Prince

Prince 7000 Bedienungsanleitung

PREMIUM STRINGER

PREMIUM STRINGER 9200 Bedienungsanleitung

Gamma Sports

Gamma Sports 602FC Bedienungsanleitung

Atlas

Atlas 8600 Bedienungsanleitung

Wilson Electronics

Wilson Electronics BAIARDO Bedienungsanleitung

Stringway

Stringway MS140N Bedienungsanleitung

Gamma Sports

Gamma Sports STII Bedienungsanleitung

Babolat

Babolat Sensor Mono Bedienungsanleitung

Babolat

Babolat SENSOR EXPERT Bedienungsanleitung

Yamaha

Yamaha Strings SS-30 Bedienungsanleitung

Hornet

Hornet PRO'S PRO Bedienungsanleitung

ATS

ATS Super Stringer II Bedienungsanleitung

Gamma Sports

Gamma Sports Els Bedienungsanleitung

PENTA

PENTA Premium Stringer 7600 Bedienungsanleitung

power tennis nederland

power tennis nederland P501 Bedienungsanleitung