Ganz ZN-L7210PHA Bedienungsanleitung

ETHERNET CAMERA, MPEG-4

ZN-L7000

INSTRUCTION MANUAL

ZN-L7210PHA

ZN-L7210NHA

Colour high resolution camera with computar autoiris varifocal

lens, MPEG-4

ENG-

rights are reserved. No part of this document may be reproduced or

transmitted for any purpose, by whatever means, be they electronic or

mechanical, without the express written permission of CBC

(EUROPE) Ltd.

Edition: October 2003 (version 6.10)

Note This manual was compiled with the greatest of care and all

information double checked. At the time of printing the description was

complete and correct. Because of the further development of the

products, the content of the manual might change without prior notice.

CBC (EUROPE) Ltd. will not be liable for damage which is directly due

to errors, incompleteness or discrepancies between the manual and

the product described.

Trade Marks All names used in this manual for hardware and software are very

probably registered trade marks and must be treated as such.

This is a class A product. In a domestic enviroment, this product

may cause radio interference in which case the user maybe

required to take adequate measures.

ENG-

INDEX

INTRODUCTION

SAFETY INFORMATIONS

PRODUCT DESCRIPTION

INSTALLATION

CONFIGURATION WITH WEB BROWSER

OPERATION WITH INTERNET EXPLORER

SERVICE

TECHNICAL SPECIFICATIONS

INDEX

ENG-

This manual is intended for persons authorized to install and operate of this camera and

VCS products .International, national and any relevant regional regulations relating to

electronics must be observed at all times.

Conventions

In this manual, the following symbols and notations are used to draw attention to special

situations:

Attention! This symbol indicates tips and notes that make using the device

easier and more convenient.

Hazard! This symbol indicates that failure to follow the safety instructions

given may directly endanger people, cause damage to the system or to other

equipment. This symbol represents a direct threat of danger.

The following typographic conventions are used in this manual:

Configuration menu names and window and key names and parameters

[Enter],[C] key names

[Ctrl]+[C] two or more keys that are pressed simultaneously

ping Command line input and output

Intended use

This camera serves to transmit video and control signals via data networks (Ethernet LAN).

This camera is designed for use in CCTV systems. The connection of an external alarm

generator allows functions to be triggered automatically. Other applications are not

permitted.

In the event of questions concerning the use of the devices which are not answered in this

manual, please contact your dealer.

This camera is compatible with following VCS products: VideoJet10e, VideoJet100e,

VideoJet1000 and Vidos softwares.

INTRODUCTION

ENG-

Electrical shock hazard

¾Never attempt to connect the unit or the mains power supply to any power network

other than the one for which it was

¾Use only appropriate and approved power supply units for the camera (see

technical specifications)

¾Do not open the housing of the power supply unit

¾Disconnect the power supply unit from the mains power supply and from all other

devices if fault occurs

¾Install the power supply unit and the unit only in a dry place protected against the

elements

¾If you are uncertain about the safe operation of the unit, shut it down immediately

and secure it to prevent any unauthorized start-up. Safe is no longer possible, for

example:

If damage is visible to the unit or the cables

If the unit no longer operates correctly

If the unit has been exposed to rain or moisture

If objects have penetrated inside the unit

After long storage under improper conditions or

After heavy demands during transport

Installation and operation

¾All applicable electrical codes and regulations must be observed and followed at all

times during the installation.

¾Before installing or operating the system, ensure that you have read and

understood the documentation for other equipment connected to the unit, e.g.

monitors or pan-tilt heads. These contain important safety notices and information

concerning permissible applications.

¾Perform only installation and operating work described in this manual. All other

work beyond this may lead to injuries to persons and damage to the system or

other equipment.

¾Ensure a secure footing whenever working in elevated positions. Use only safety

ladders. If necessary, use safety harness or railings.

¾Use this camera with original Ganz tools.

Repairs and maintenance

¾Never open the housing of the unit.

¾Never open the housing of the power supply unit.

¾Ensure that only qualified, specialist personnel are permitted to carry out

maintenance or repair work.

¾Contact your dealer for authorized reparation.

SAFETY INFORMATIONS

ENG-

Preconditions for commissioning

¾Computer with operating system Windows 98/2000/XP and gateway to the network

¾Microsoft Internet Explorer web browser (from version 5) or free serial interface and

terminal program

Preconditions for configuration

¾Computer with operating system Windows 98/2000/XP and gateway to the network

¾Microsoft Internet Explorer (from version 5) and MPEG-ActiveX

Preconditions for operating

¾Computer with operating system Windows 98/2000/XP and gateway to the network

¾Microsoft Internet Explorer (version 5) and MPEG-ActiveX

¾VideoJet10e / VideoJet100e with PAL/NTSC monitor or software VIDOS

Functions

This device is a high-resolution colour camera for professional use in CCTV system. It has

an integral video server for encoding of the video and control signals for the transfer via an

Ethernet LAN.

The camera ¼” CCD offers a horizontal resolution of 480TVL(PAL)/470TVL(NTSC). The

camera is characterized by a 4X computar varifocal lens, automatic DC.

All the camera parameters are conveniently set via HTML pages using an internet browser,

except flickerless function, BLC and iris setup.

Main functions are:

¾Automatic DC iris and varifocal lens

¾BLC and flickerless

¾Picture saturation regulation

¾Analog video output PAL/NTSC (BNC) for focus and iris setup

PRODUCT DESCRIPTION

ENG-

Multicast functions

This camera supports the standard MPEG-4. Thanks to efficient encoding, the data

transmission rate remains low, even with maximum image quality and 25 images/s;

furthermore, it can be adapted over a wide range to meet the local requirements.

In appropriately configured networks, the multicast function permits the simultaneous video

transmission in real time to several receivers. A precondition for this is the implementation

of the UDP and IGMP protocols in the network.

Remote control

For remote control of external equipment, the control data is transmitted via the

bidirectional serial interface of the unit. This interface can also be used for the

transmission of transparent data.

Configuration

This camera can be configured with a browser via the local network or via

Internet. Firmware updates and the quick uploading of device configurations

are possible in the same way. Please consider that disconnecting the

camera or power supply loss during the firmware update function can

seriously damage the camera.

Recording and playback

You can save live pictures recorded by the unit as files on the hard disk of your computer.

The video pictures are stored in MPEG-4 format and can, for example, be replayed with

MPEG Player included in delivery.

The RAM memory integrated in the unit serves as pre-alarm memory. On this ring buffer

video pictures are recorded as long as there is no active connection to a receiver unit

(duration ~19 secs.).

Summary

¾Video and data transmission via data networks

¾Digitally optimized video data

¾Automatic iris control

¾4X Varifocal lens

¾Multicast or video streaming multicast connection

¾Locale analog (PAL) video output

¾25 FPS (high res.)

¾MPEG-4 or M-JPEG

¾Integral Ethernet interface 10Base-T

¾Transparent bidirectional data channel via serial interface RS232 RS485/422

¾Remote control of internal functions via TCP and UDP

¾3-steps password protection

¾Alarm input (NO or NC)

¾Relay (NO or NC)

¾Automatic connection on alarm

¾Integrated activity detector

¾email on alarm

¾Firmware upgrade by flash memory

ENG-

1 2 4

5 / 8

4 12VDC

5 GND

6 Alarm input (NO/NC)

7 Alarm input GND

1 Relay COM

2 Relay NO (closed when camera off)

3 Relay NC (opened when camera off)

Connectors and Controls

1 DC iris: ON

2 Flickerless: ON/OFF

3 BLC: ON/OFF

4 Always ON

5 VR for iris adjustment

6 Zoom adjustment

7 Focus adjustment

8 DC iris connector

1 Serial port RS232/RS485/422

2 Power led

3 Local analog video output (BNC)

4 Ethernet 10Base-T

5 Power, alarm, relay

1 2 3 4 5 6 7

ENG-

The camera is designed for indoor operations. Choose a site for installation which

ensures that camera is exposed to neither extreme temperatures nor extreme

moisture or humidity. The ambient temperature must lie between +5 and +40°C,

the relative humidity must not exceed 80%.

During operation, the unit generates a great deal of heat. Therefore ensure

sufficient ventilation and an adequate distance to heat-sensitive equipment or

objects.

Please observe the following installation conditions:

¾Do not install the camera in the immediate vicinity of radiators or other sources of heat.

Avoid installing the camera where it is exposed to direct sunlight.

¾Ensure sufficient space for laying the cables.

¾Ensure adequate ventilation of the camera.

¾For all cable connections, use only the suitable cables which also prevent any electrical

interference, where necessary.

¾Ensure that the camera is not exposed to water at the installation site. If necessary, use

fresh desiccant in waterproof housing to avoid moisture due to condensation.

¾Lay and install all cables in such a way that they cannot be damaged and ensure

sufficient strain relief.

¾The installation always depends on the actual situation. No concrete instructions can

therefore be given here. The camera has a standard ¼” thread which can be installed

on both the top and bottom of the housing.

¾Lay all cables up to the installation position.

¾If necessary, connect a monitor with a coax cable (75 Ohm) to the BNC jack in order to

be able to check the video image on the spot.

¾Connect the leads of the power supply unit to terminals + and – of the DC 12V

CONNECTOR. Pay attention to the correct connection of the leads.

Network connection

You can connect the camera via hub to a 10Base-T network. Use a standard UTP Category 5

with RJ45 connectors.

INSTALLATION

ENG-

Alarm input, relay output

The alarm input of the camera serves for the connection of an external alarm trigger. If

configured accordingly, an alarm trigger can, for example, set up an automatic connection

between the camera and a remote station.

The relay output serves for switching external devices. This control output can be used

interactively during an active connection with the camera. The contact can be programmed as

NO or NC and it is possible to invert the mechanical function by software setup. However, the

NC terminal will open if the camera is powered down and the NO will close. In this way the

camera is able to show also a power loss failure.

The relay contact must not be subjected to a burden of more that 30 V and 1A.

Serial port

The serial port is commonly used to drive connected pan-tilt devices.

Read carefully the related manuals before to connect them to the camera.

Uncorrected use of serial port can damage the camera.

Pin layout:

Pin RS232 RS485/422

1 RX RX+

2 TX TX-

3 RTS TX+

4 CTS RX-

5 GND GND

Power supply

This camera has no mains power switch. When you have connected the power supply unit to

the device and inserted the power unit plug into a mains socket, the device is ready for

operation.

Connector soldering side

1 2

3 4

5 6

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ganz Sicherheitskamera Handbücher

Ganz

Ganz ZC-DN3048PHA Bedienungsanleitung

Ganz

Ganz ZN-PTZ500VPE Bedienungsanleitung

Ganz

Ganz ZC-D8000 SERIES Bedienungsanleitung

Ganz

Ganz ZC-BT SERIES Bedienungsanleitung

Ganz

Ganz Lite LDB series Bedienungsanleitung

Ganz

Ganz PIXELPRO SERIES Bedienungsanleitung

Ganz

Ganz PIXELPRO SERIES Bedienungsanleitung

Ganz

Ganz ZC-D4000 Series Bedienungsanleitung

Ganz

Ganz ZN-DT350VE Gebrauchs- und Wartungshandbuch

Ganz

Ganz ZC-DT8039NXA-IR Bedienungsanleitung

Ganz

Ganz PixelPro GXi ZN1-D4FN5 Bedienungsanleitung

Ganz

Ganz ZC-D5000NXA series Bedienungsanleitung

Ganz

Ganz PIXELPRO SERIES Bedienungsanleitung

Ganz

Ganz ZC-DT8312NHA-IR Bedienungsanleitung

Ganz

Ganz ZC-L1210NHA Bedienungsanleitung

Ganz

Ganz ZC-PT236 Bedienungsanleitung

Ganz

Ganz ZC-PT series Bedienungsanleitung

Ganz

Ganz Lite VRDDN-2812Y60 Bedienungsanleitung

Ganz

Ganz ZC-D5000 NXA series Bedienungsanleitung

Ganz

Ganz Genstar ZNT8-BA1F-T Series Bedienungsanleitung

Ganz

Ganz PixelPRO ZN-DT2MA Bedienungsanleitung

Ganz

Ganz ZN-CM1 Bedienungsanleitung

Ganz

Ganz C-AllView Montageanleitung

Ganz

Ganz ZN-PT series Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung