GARDINER TECHNOLOGY GARDTEC 590 Bedienungsanleitung
GG
GGAA
AARR
RRDD
DDTT
TTEE
EECC
CC
55
5599
9900
00
//
//
55
5599
9911
11
LCD User Instructions
&
LED User Instructions
GARDINER TECHNOLOGY
PR5075U.qxd 19/06/00 10:59 Page 1
Contents
Using LCD Keypads
Introduction................................................................... 2
User Code Types.......................................................... 2
Setting The System ...................................................... 3
Unsetting The System .................................................. 3
Part Setting The System............................................... 4
Removing Zones........................................................... 5
Testing The System...................................................... 6
Viewing The Event Log................................................. 7
Changing The Chime Status......................................... 8
Programming User Codes ............................................ 9
Programming Time & Date ........................................... 10
User Initiating Remote Access ..................................... 11
Resetting After An Alarm .............................................. 12
Resetting After Mains Failure ....................................... 13
Using LED Keypads.................................................... 13
Setting The System ...................................................... 13
Unsetting The System .................................................. 14
Part Setting The System............................................... 14
Area Setting.................................................................. 15
Removing Zones........................................................... 23
Testing The System...................................................... 16
Viewing The Event Log................................................. 17
Changing The Chime Status......................................... 18
Programming User Codes ............................................ 18
User Initiating Remote Access...................................... 19
Resetting After An Alarm .............................................. 20
Resetting After Mains Failure ....................................... 20
LED Display Glossary................................................... 21
System Attributes.......................................................... 23
Service Record ............................................................. 23
User Chart .................................................................... 24
ACE Instructions........................................................... 25
Programming ACE Keyfobs onto your System............. 26
Page 1
GARDTEC
590/591
User Manual
PR5075U.qxd 19/06/00 10:59 Page 1
Page 2
GARDTEC
590/591
User Manual
Introduction
Two types of display variation are available, LCD giving two rows of 16 character
English text and may be used on the Gardtec 591 and LED giving two 7 segment LED
digits that may be used on the Gardtec 590 & 591.
Please take time to familiarise yourself with the type of equipment fitted to your
premises as it will prove invaluable whilst using this manual.
User Code Types
Four types of User Codes are available on the Gardtec 590/591
,
each user code type
allows for different levels of access. In total 7 User codes may be programmed by a
Master Level User Code.
User number 1 will always be a Master Level User but the remaining 6 User Codes
may be programmed (by a Master Code) to the required level of access. These may be
changed at any time via a Master level code
The User Code levels available and the functions available for the levels are:-
1 = Set Only Only Allows for the setting of the system.
2 = Main User Allows Setting, Part Setting, Zone Remove (if programmed
by engineer), System Test, Unsetting, Reset after Alarm (if
programmed by engineer).
3 = User Allows Setting, Part Setting, Reset after Alarm (if
programmed by engineer), Unsetting.
4 = Master Allows Setting, Unsetting, Zone Remove (if programmed by
(User 1 always Master) engineer), Test System, View Log, Chime On/Off, User
Codes, Set Time/Date, Reset After Alarm (if programmed
by engineer), Unsetting.
PR5075U.qxd 19/06/00 10:59 Page 2
Page 3
GARDTEC
590/591
User Manual
Setting The System
This section is for systems fitted with LCD keypads for
LED keypads please refer to page 13
1) With the display showing:-
2) Enter the User code (followed by YES if
Master or Main type code has been used).
The display will show:-
and a continuous exit tone will sound
3) Exit the premises via the authorised exit
route (the exit tone will change if any detectors
are violated during exit)
4) Once the premises are secure listen that the exit
tone returns to the continuous tone.
5) Wait until the exit tone finishes before leaving.
Unsetting The System
1) Enter the premises via the authorised entry route
(the broken entry tone will sound),
proceed to the keypad.
2) At the keypad enter a valid code, the display
will show:-
3) The system is now unset.
< < < < UN-SET > > > >
01 JAN 18 : 58 : 01
EXIT Now !
All Zones ON 15
< < < < UN-SET > > > >
01 JAN 18 : 58 : 01
PR5075U.qxd 19/06/00 10:59 Page 3
Page 4
GARDTEC
590/591
User Manual
Part Setting The System
(using Master & Main type codes)
1) With the display showing:-
2) Enter a Master or Main type code, the
display will show for example:-
3) Press 1, 2 or 3 (for Part 1, 2 or 3), the
display will show for example:-
4) The exit tone may or may not be heard
dependant on the system settings.
5) Exit the premises or retire to an unprotected
part of the system. At the end of the exit time
either the exit sounder will stop or a single
beep will be emitted (dependant on system
settings).
< < < < UN-SET > > > >
01 JAN 18 : 58 : 01
Do you want to . .
Set ?
EXIT Now!
Part 1 15
PR5075U.qxd 19/06/00 10:59 Page 4
Page 5
GARDTEC
590/591
User Manual
Removing Zones
(Master & Main codes only)
If programmed by the installation company individual zones may be removed, this may
only be done by a Master or Main level of code.
1) With the display showing:-
2) Enter a Master or Main level code,
the display will show:-
3) Press NO, the display will show:-
4) Press YES, the display will show:-
5) Enter the zone number you wish to
remove followed by YES (pressing
NO will 'un-remove' a zone), the
display will show:-
6) Repeat step 5 until you have removed all
the required zones.
7) Press 0 to escape, the display will show:-
8) Press YES, the continuous exit tone will
sound.
9) Exit the premises via the authorised
exit route ( the exit tone will change as detectors
are violated). When the premises are secure
listen that the exit tone returns to the continuous
tone. Wait until the exit tone finishes before leaving.
Note: Zone remove is only effective for the one set.
< < < < UN-SET > > > >
01 JAN 18 : 58 : 01
Do you want to . .
Set ?
Do you want to . .
Set ?
Do you want to . .
REMOVE Zones ?
Enter Zone No. - -
then + YES or - NO
Enter Zone No. - -
then + YES or - NO
PR5075U.qxd 19/06/00 10:59 Page 5
Page 6
GARDTEC
590/591
User Manual
Testing The System
(Master & Main codes only)
1) With the display showing:-
2) Enter a Master or Main level code,
the display will show:-
(User Names on 816 & 840 Only)
3) Press NO, the display will show:-
4) Press NO, the display will show:-
5) Press YES, the display will show:-
for 3 seconds
Then for example:-
6) Pressing 1 will enter zone Status mode (All zones will show on the display
and will be deleted as each zone is triggered). Press 0 to escape.
Pressing 6 will silence the internal sounder,
Pressing 4 will toggle the Strobe On/Off,
Pressing 9 will toggle the Bell On/Off
7) Whilst in Test mode any zones violated
will sound the internal sounder (if it has
not been silenced) and show on the
display.
8) When you have finished testing the
system press 0 twice, the display will show:-
< < < < UN-SET > > > >
01 JAN 18 : 58 : 01
Do you want to . .
Set ?
Do you want to . .
REMOVE Zones ?
Do you want to . .
TEST the System ?
1=Status 4 = Strobe
6 = Sounder 9 = Bell
< All Zones OK >
TESTING . . .
< < < < UN-SET > > > >
01 JAN 18 : 58 : 01
PR5075U.qxd 19/06/00 10:59 Page 6
Page 7
GARDTEC
590/591
User Manual
Viewing The Event Log
(Master code only)
1) With the display showing:-
2) Enter a Master Code, the display
will show for example:-
3) Press NO three times, the display
will show:-
4) Press YES, the display will show:-
for 3 seconds
Then, for example:-
5) This is the most recent event in the log.
Whilst viewing the Log,
Pressing NO will move back to the previous event.
Pressing YES will move forward to the next event.
Pressing 7 will take you back to the last event of
the previous day.
Pressing 9 will take you forward to the first event of
the next day.
6) When you have finished viewing the Log press 0 twice
the display will show:-
< < < < UN-SET > > > >
01 JAN 18 : 58 : 01
Do you want to . .
Set ?
Do you want to . .
View the LOG ?
While Viewing . . .
1 = Printer On / Off
Read Log
01 JAN 18 : 58 : 01
< < < < UN-SET > > > >
01 JAN 18 : 58 : 01
PR5075U.qxd 19/06/00 10:59 Page 7
Page 8
GARDTEC
590/591
User Manual
Changing The Chime Status
(Master code only)
The Chime zones will have previously been programmed by the installation company.
A Master level code may change the status of the Chime between On and Off. To do
so proceed as follows:-
1) With the display showing:-
2) Enter a Master Code, the display will
show for example:-
3) Press NO four times, the display will show:-
4) Press YES the display will show for example:-
Or:-
5) Press NO to change the status of the Chime,
then press YES, the display will show:-
6) Press 0 to escape, the display will show:-
< < < < UN-SET > > > >
01 JAN 18 : 58 : 01
Do you want to . .
Set . ?
Do you want to . .
Change Chime ?
Chime is Off ok ?
Chime is On ok ?
Do you want to . .
Change Chime ?
< < < < UN-SET > > > >
01 JAN 18 : 58 : 01
PR5075U.qxd 19/06/00 10:59 Page 8
Page 9
GARDTEC
590/591
User Manual
Programming User Codes
(Master code only)
1) With the display showing:-
2) Enter a Master Code, the display will show:-
(User Names on 816 & 840 Only)
3) Press NO five times, the display will show:-
4) Press YES, the display will show:-
(1 - 7) displayed on 800 & 816
5) Enter the user number (1 to 7) that you
wish to program followed by YES, the
display will show:-
6) Enter the code you require (codes may be 4,
5 or 6 digits) followed by YES.
(Entering 000000 will delete an existing code)
Note: If the code already exists or is a duress of
another code an error will be shown,
choose another code and return to step 6
7) The display will show:-
(not if user 1 is being programmed).
The display will scroll showing the code
types available (see user types or display).
8) Enter the required type followed by YES,
the display will show:-
9) If you wish to program other User Codes
return to step 4
Or
Press 0 to return to:-
< < < < UN-SET > > > >
01 JAN 18 : 58 : 01
Do you want to . .
Set ?
Do you want to . .
Prog. USER CODES ?
Enter User No. - -
(1- 7) Then YES
Now Enter Code . .
- - - - - - Then YES
Choose Type . . -
0 = xxxxxx 1 = xxxxxx
Do you want to . .
Prog. USER CODES ?
< < < < UN-SET > > > >
01 JAN 18 : 58 : 01
PR5075U.qxd 19/06/00 10:59 Page 9
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere GARDINER TECHNOLOGY Bedienfeld Handbücher
