Garmin GPS-III+ Gebrauchs- und Pflegehandbuch

Inhaltsverzeichnis

Andere Garmin GPS Handbücher

Garmin

Garmin G300 for Cessna SkyCatcher Handbuch

Garmin

Garmin GTU 10 Bedienungsanleitung

Garmin

Garmin GTS 8 Series Bedienungsanleitung

Garmin

Garmin GNS 530 Bedienungsanleitung

Garmin

Garmin Trail Guide Bedienungsanleitung

Garmin

Garmin nuvi 680 Bedienungsanleitung

Garmin

Garmin GPS GPS 60 Bedienungsanleitung

Garmin

Garmin GPSMAP 192C Betriebsanleitung

Garmin

Garmin Alpha 300i Bedienungsanleitung

Garmin

Garmin GPSMAP 276C Referenzhandbuch

Garmin

Garmin GPS 152 - Marine Receiver Bedienungsanleitung

Garmin

Garmin GPSMAP 3006C Bedienungsanleitung

Garmin

Garmin Cessna Caravan G1000 Handbuch

Garmin

Garmin CamperVan Bedienungsanleitung

Garmin

Garmin GNS 530 Bedienungsanleitung

Garmin

Garmin E Trex 30 Bedienungsanleitung

Garmin

Garmin nuvi 885 Gebrauchsanweisung

Garmin

Garmin Cessna Caravan G1000 Handbuch

Garmin

Garmin inREACH SE Gebrauchsanweisung

Garmin

Garmin AA2401 Bedienungsanleitung

Garmin

Garmin TREAD Bedienungsanleitung

Garmin

Garmin AERA 660 Gebrauchsanweisung

Garmin

Garmin eTrex eTrex Bedienungsanleitung

Garmin

Garmin nuvi 1350 Gebrauchsanweisung

Beliebte GPS Handbücher anderer Marken

Hama

Hama 53118 Bedienungsanleitung

Jigabot

Jigabot EX Bedienungsanleitung

Pointer

Pointer Cellocator CelloTrack XT LTE Installationsanleitung

Queclink

Queclink GV55LITE Bedienungsanleitung

Voxson

Voxson Voxtrack GPS500 Gebrauchsanweisung

Starcom Systems

Starcom Systems Kylos Compact Bedienungsanleitung

Cobra

Cobra Marine MC 600Ci Bedienungsanleitung

Cellocator

Cellocator CelloTrack T Bedienungsanleitung

Enfora

Enfora Mini-MT GSM2228UG001 Bedienungsanleitung

Magellan

Magellan eXplorist 100 Bedienungsanleitung

LTE

LTE G50B Bedienungsanleitung

SkyGolf

SkyGolf SkyCaddie SG1 Bedienungsanleitung

Kenwood

Kenwood DNN9330BT Bedienungsanleitung

Safelet

Safelet Indra Bedienungsanleitung

Bushnell

Bushnell 360100 Bedienungsanleitung

Geneq

Geneq SXBlue Bedienungsanleitung

ORIGO

ORIGO ED308 Bedienungsanleitung

Magellan

Magellan RoadMate 66 Series Bedienungsanleitung

Garmin® GPS-III+ Backup Battery Replacement

If you receive a screen message that your backup battery has lost charge, it is time to

replace it. Here is how.

1. Tools and supplies

a. Japanese JIS Standard “Phillips” head screwdrivers. These drivers are cut

in a different manner and provide a good grip on the screws. You will

mess the screws up if you do not use JIS screwdrivers.

b. De-soldering gun, de-soldering braid or solder sucker.

c. Soldering station with a fine tip

d. Solder

e. Precision sidecutters

f. Battery. Panasonic VL1220-1VC. These are available from

www.mouser.com

1. Replacing the battery. If you do not have the equipment and ability to do fine

soldering do not attempt this project. Please note that removing the backup

battery will delete all waypoints and other stored information.

a. Remove six screws from the back of the case

b. Carefully open the case. There is a connector cable that you can damage

if it suddenly pops open.

c. Using a jeweler’s screwdriver, gently pry up the white cable connector

from the circuit board and set the back of the case aside.

d. Locate the battery. It is on edge next to a capacitor just to the left of the

white connector.

e. Using a jeweler’s screwdriver, pull the plastic clamp back on the brown

ribbon cable to the stops.

f. Remove the screw near the metal can on the antenna end of the board.

g. Gently tip the board up, hinging on the ribbon cable edge. The board will

stick and it will take some leverage to get it up. The ribbon cable will

slide out of the clamp.

h. Turn the board over and locate the battery pads on the back side of the

circuit board and remove the solder.

i. Remove the battery and clean the holes in the pad.

j. Insert the new battery, and check the polarity. The positive side of the

battery should be towards the metal can on the antenna end.

k. Solder the battery leads and trim them.

l. Replace the board in the chassis. Slide the ribbon cable into the clamp, set

the board in place, and install the screw.

m. Replace the white cable clamp

n. Making sure antenna wire is not pinched, reassemble the case and install

the screws.

o. You are done!