GE Interlogix 5812RND - Security ShatterPro III Acoustic Glassbreak... Bedienungsanleitung

5812-RND Acoustic Glassbreak Detector

AcousticGlassbreak

Detector

5812-RND

InstallationInstructions

Description

The 5812-RND is an acoustic glassbreak detector designed

to detect breaking glass from framed windows in the

perimeter of a building. The detector is mounted in the

building interior and uses a power supply from a 12VDC

control panel. The detector is available in a low-profile

round housing.

Features

The detector provides the following features:

•Range-5 to 25 feet (1.5 to 7.6 m)

•Alarmmemory-After an alarm and until power is

cycled, the alarm memory can be checked with the hand-

clap test.

•LEDindicator-Red LED provides detector test and

status indication.

•Tamper resistant - Provides a screw that secures the

cover to the base to prevent tampering.

•Hand-clap test - In addition to a test mode, you can

confirm the operation of the microphone by clapping

your hands.

What You Will Need

You need the following tools and parts to install the

detector:

• 5812-RND detector including screw to secure the cover

to the base

• Screws and wall anchors

• Flat-blade screwdriver

• Phillips screwdriver

• Sentrol 5709C hand-held tester

Selecting a Location for the

Detector

The detector can be mounted on ceilings or on walls

opposite or adjacent to the window to be protected. See

Figure 2.

Use the following guidelines to determine the best location

to install the detector.

• Mount at least 5 feet (1.5 m) from glass windows

being protected.

• Windows must be at least 12 x 24 inches

(30.5x61cm) square.

• Avoid locations where lined, insulating, or sound

deadening drapes are used.

• Mount 12 inches (30.5 cm) away from wall corners.

• Avoid locations where interior closed wooden

shutters are used.

• Locate in a suitable envionment as follows:

- Temperature between 32° and 122°F (0° and 50°C)

- Humidity between 10 and 90% non-condensing

• Mount the detector on a stable surface up to 25 feet

(7.6 m) from the farthest point on the glass surface.

See Figure 2.

• Avoid locations that expose the detector to possible

false alarm sources such as:

- Glass airlocks and vestibule areas

- Kitchens

- Residential car garages

-Small utility rooms

-Stairwells

- Bathrooms

- Small acoustically live rooms

- Air vents

Figure 1. 5812-RND

Figure 2. Mounting Locations

Wallmount

Ceilingmount

25’(7.6m)

max.

25’(7.6m)

max.

LISTED

25812-RND Acoustic Glassbreak Detector

Selecting the Best Location for

Multiple Window Coverage

The detector has a 360degree coverage pattern that can be

used to cover several windows in a single room as follows:

• Draw an imaginary line from the center of each window

to be covered in towards the center of the room.

• Mount the detector as close to where the lines intersect

as possible. See Figure 3.

• Do not mount the detector at more than a 60 degree

angle from the center of any window to be protected.

See Figure 3.

Installing the Detector

All wiring must conform to the National Electric Code

(NEC) and/or local codes having jursidiction.

Important !Important !

Important !

Ifyou areunsureaboutalocation, connecta9V

batteryto thedetector andtest itbefore

permanently mounting. SeeTesting theDetector.

Use the following steps to install the detector:

1. Run the security system wiring to the detector location.

2. To remove the front cover, press the release tab on the

lip of the base, twist the cover counter clockwise, and

liftoff. See Figure 4.

3. Remove the appropriate wiring and mounting

knockout holes from the base. See Figure 6.

4. Pull the wires through the knockout holes and use two

screws to attach the base to the surface. Use wall

anchors if necessary.

5. Strip 1/4 inch of insulation from each wire.

6. Connect the system wires to the appropriate screw

terminals on the base and tighten the screws. See

Figure 7.

7. To replace the cover, line up the tabs on the base with

the corresponding tabs on the cover, press together

and turn clockwise until the cover snaps firmly into

place. See Figure 5.

8. Apply power. The red LED should flash once.

9. Test the detector. See Testing the Detector.

Figure 3. Multiple Window Coverage

Figure 4. Housing Parts

Figure 5. Attaching the Cover

Figure 6. Detector Knockout Locations

CeilingCeiling

Ceiling

mountmount

mount

Detector

60 max.

Microphone

LED

Releasetab

Knockouts

5812-RND Acoustic Glassbreak Detector

Figure 9. Testing the Range

GND +12V N.C. COM

Figure 7. Wiring Terminals

• Single

• Continuous Plate •

Tempered •

Laminated •

Battery LED

Battery is OK if LED

stays on during test

5709C

Shatter SeriesTester

Use for testing:

ShatterPro

Shatterbox

Shatterbox II

ShatterSwitch

SENTROL

Figure 8. Using the Tester

When the detector is in test

mode, the LED lights steady for

4 seconds, then flashes for 60

seconds. Time resets after

each valid test.

Hold the tester so that the

speaker is within 1” (2.5cm) of

the detector microphone.

1”(2.5cm)

Testing the DetectorTesting the Detector

Testing the Detector

To verify detector range and operation, you need the

Sentrol 5709C hand-held tester.

Use the following steps to test the detector:

1. Set the tester to the appropriate glass-type setting.

Use the tempered setting if you are unsure about the

glasstype.

2. Put the detector in test mode as follows:

- Hold the tester 1” from the detector. See Figure 8.

- Activate the tester.

The LED on the detector lights for 4 seconds and then

starts flashing to indicate the detector is in test mode.

The relay opens for 4 seconds, then returns to

standby.

3. Hold the tester near the surface of the glass to be pro-

tected and aim the speaker at the detector. Be sure the

tester is at the point on the glass farthestfrom the

detector. If closed drapes or curtains are present, hold

the tester behind them. See Figure 9.

4. Press the test button on the tester. The LED on the

detector should stay on for 4 seconds to indicate the

glass is within detection range of the detector. If the

LEDdoesnotstay on for 4 seconds, move the detector

and retest.

Understanding the LED

The red LED located on the front of the detector

indicates the status of the unit as follows:

Status LED Indication

Power on Flashes once when power is applied.

Clap test/Alarm In response to the clap test:

memory Flashes twice to indicate the detector has

power and is functioning properly.

On for 4 seconds to indicate the detector

has alarmed.

Alarm On for 4 seconds with relay when

breaking glass is detected.

Test mode On for 4 seconds with relay, then flashes

for 60 seconds. Each test trigger resets

the test mode clock and the LED starts

over flashing for 60 seconds.

45812-RND Acoustic Glassbreak Detector

Using the Hand-Clap Test and

Alarm Memory

The alarm memory and microphone operation can be

checked with the hand-clap test as follows:

1. Standing under the detector, clap your hands together.

2. Observe the LED on the detector.

Ifthe detectorhaspowerandis functioningproperly,the

LED quickly flashes twice.

Ifthe detector has alarmed, the LED will light for 4 seconds.

Cycle the power to clear the alarm memory.

The hand-clap test is intended as a functional test, does not

open the relay, and is not an accurate indication of detector

range.

Maintaining the Detector

When installed and used properly, the detector provides

years of service with minimal maintenance.You should test

the detector annually to ensure proper operation.

Clean the cover with a damp (water) cloth as needed to keep

it free of dust and dirt. Always test the detector after

cleaning.

FCC Compliance

This device complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received,

including interference that may cause undesired operation.

Specifications

Input voltage ........................................ 12VDCNominal

Current

Typical ................................................................ 15mA

Maximum ............................................................. 25mA

Electrical configuration ........................................FormA

Relay rating............................................. 16V,50mAmax.

Detection range .................... 5’-25’(1.5m-7.6m)x360°

(use for rooms 100 sq. ft. and larger)

Alarm response...................................................... 4 sec.

Minimum glass size............... 12”x24” (30.5cmx61cm)

Recommended glass thickness:

Plate................................ 3/32”- 1/4”(2.4mm- 6.4mm)

Tempered .........................1/8”-1/4” (3.2mm- 6.4mm)

Wired....................................................... 1/4”(6.4mm)

Laminated................................................ 1/4”(6.4mm)

Operating temperature ................. 32°- 122°F(0° -50°C)

Relative humidity ................... 10 - 90% non-condensing

Dimensions:

Depth ......................................................0.81”(2.1cm)

Diameter ..................................................4.0” (10.2 cm)

Color ..................................................................... White

Fieldwiring size ............................................ 18-24AWG

Listing ............................................................... C-ULUS

1038240 RevA 06/02

12345 SW Leveton Drive

Tualatin, OR 97062

www.interlogixsecurity.com

www.sentrol.com

Phone: 503-692-4052

USA & Canada: 800-547-2556

Technical Service: 800-648-7424

FaxBack: 800-483-2495

GE Interlogix

Product Ordering

Model Number Description

5812-RND Acoustic glassbreak sensor, round housing, FormA

Accessories

5709C Glassbreak hand-heldtester

Dieses Handbuch passt für folgende Modelle

Andere GE Interlogix Sicherheitssensor Handbücher

GE Interlogix

GE Interlogix GS930 Bedienungsanleitung

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

Siemens

Siemens AZL66 Series Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

Bosch

Bosch DS835 Bedienungsanleitung

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung

Solinst

Solinst 301 Bedienungsanleitung