GE Security Phoenix A8950CC Bedienungsanleitung

Security

Phoenix Fiber Optic Communication System

A8950CC

installation instructions

11-A8950CC

Installation Instructions

BEFORE YOU BEGIN 1

GETTING STARTED 2

Overview 2

Determine Mounting Configuration 2

Installing Power Supply 2

INSTALLING THE OPTICAL TRANSCEIVER MODULE 3

Point-to-Point, Repeater, Self-Healing Ring Diagrams 4

LED Operating Status 5

INSTALLING THE DATA MODULE 6

Configuring the Data Module 6

Install Data Module 7

Connect Data Module 7

Channel Mapping 7

Connection Instructions 8

RS-232, TTL, RS-422, RS-485, Manchester/Biphase Interface 9

RS-485, Sensornet, Test Mode 9

Data Module - Channel Sequence 10

INSTALLING THE ETHERNET MODULE 11

Install Ethernet Module 11

Connect Ethernet Module 12

INSTALLING THE VIDEO MODULE 13

Install Video Input Module 13

Install Video Output Module 13

Connection Instructions 14

Video Module - Channel Sequence 15

INSTALLING THE AUDIO MODULE 16

Configuring the Audio Module 16

Audio Input Termination Diagrams 17

Audio Input/ Output Charts 18

Audio Module - Channel Sequence 19

INSTALLING THE CONTACT CLOSURE MODULE 20

Install Contact ClosureModule 20

Connection Instructions 21

RJ45, Contact Input/ Contact Output Charts 22

Contact Input/ Contact Output - Channel Sequence 22

CONFIGURING THE PHOENIX FIBER OPTIC COMMUNICATION SYSTEM 23

Turn on power and check status 23

Select the system topology 24-26

Set the node ID 26

FRONT PANEL MENU TREE AND DESCRIPTIONS 27

Main Menu Options 28-31

Menu Options: Video 31-33

Menu Options: Data 34-36

Menu Options: Ethernet 37

Menu Options: Audio 38-39

Menu Options: Contact Closure 39-41

MAIN LOCAL POWER/ MAIN LOCAL TEST/ MAIN LOCAL ABOUT 41-42

MAIN REMOTE/ MAIN ABOUT 42-43

BLANK PANEL SPECIFICATIONS AND LIMITED WARRANTY44

OPTICAL TRANSCEIVER MODULE SPECIFICATIONS 45

DATA MODULE SPECIFICATIONS 46

ETHERNET MODULE SPECIFICATIONS 47

VIDEO MODULE SPECIFICATIONS 48

AUDIO MODULE SPECIFICATIONS 49

CONTACT CLOSURE MODULE SPECIFICATIONS 50

CUSTOMER SUPPORT 50

Phoenix Fiber Optic Communication System

Before You Begin

Read these instructions before installing or operating this product.

Note: This installation should be made by a qualified service person and should conform to local codes.

This manual provides installation and operation information.

To use this document, you must have the following minimum qualifications:

•Abasic knowledge of CCTV systems and components

•Abasic knowledge of electrical wiring and low-voltage electrical hookups

Intended Use

Use this product only for the purpose for which it was designed; refer to the product

specification and user documentation.

Customer Support

For assistance in installing, operating, maintaining, and troubleshooting this product,

refer to this document and any other documentation provided. If you still have questions,

please contact technical support during normal business hours (Monday through Friday,

excluding holidays, between 6 a.m. and 5 p.m. Pacific Time).

GE Security

Call: 888 437-3287 (US, including Alaska and Hawaii; Puerto Rico; Canada)

Outside the toll-free area: 503 885-5700

Fax: 561 998-6224

Note: You should be at the equipment and ready with details beforecalling Technical Support.

Conventions Used in this Manual

Boldface or button icons highlight command entries. The following WARNING,

CAUTION, and Note statements identify potential hazards that can occur if the

equipment is handled improperly:

*WARNING:

Improper use of this equipment can cause severe bodily injury or equipment damage.

** CAUTION:

Improper use of this equipment can cause equipment damage.

Note: Notes contain important information about a product or procedure.

*This symbol indicates electrical warnings and cautions.

** This symbol indicates general warnings and cautions.

Overview

Installing the Phoenix chassis is a three-step process:

1. Install mounting hardware and power supplies.

2. Install modules and connect cabling.

3. Configure the system.

Determine Mounting Hardware

Mounting brackets are adjustable. Choose the best location to fit your application and

position brackets using the supplied hardware. Remove screws holding front mounting

bracket, move to top, bottom, back or front and refasten.

Installing Power Supplies

All installation should be from rear of rack unit.

Toinstall power supply, slide power supply in slot "A" and secure with hardware. Remove

center support panel and use to cover open slot if redundant power supply is not used.

Optional Redundant Power Supply: When using the redundant power supply, remove panel

and insert second power supply in slot "B" and secure.

** CAUTION:

This product contains ESD-sensitive components. Although all precautions have been made to

reduce ESD susceptibility, use good grounding techniques when handling uninstalled modules.

Getting Started

Specifications

Model A8960AC

Size

Weight

Model Part Number

Optional Redundant Power Supply

A8960AC

1.65 in. W x 3.30 in. H x 8.00 in. D (42 x 84 x 203 mm)

1.25 lb.(5.67 g)

Electrical

•Input power: 100 V to 240 V, 60 to 50 Hz

•Current requirement: 2 A

•Power consumption: 40 W

•Protection: 250 V, 2 A fuse

Model

Slot B

Model Part Number

Active fuse

Model PartNumber

Spare fuse

Model

Slot A.

Module Installation

The Optical Transceiver is the first module to be installed.

Overview

The Phoenix optical transceiver module is used to provide connectivity to the fiber

connections between nodes. The A8972FLC optical transceiver module contains a single

optical transceiver with dual LC connectors and is used as an ‘end node’ in either a point

to point, or linear system. The A8974FLC optical transceiver module features two optical

transceivers with two dual LC connectors and is used in repeating nodes within a linear

system as well as all nodes in a self-healing ring system.

Tools and materials required

The optical module is held in place with simple thumbscrews with screwdriver slots.

The only tool recommended is a small flat blade screwdriver.

Installation instructions:

1. Install optical transceiver module in slots 9 and 10 (color-keyed white) and secure.

INSERT OPTICAL TRANSCEIVER MODULES IN SLOTS 9-10 (White)

2. Connect fiber:

Connect single-mode fiber optic cables by using LCconnectors. Each portconnects to a

pair of fibers. The top fiber in a port is the laser output (Tx) and the bottom fiber is the

photo diode input (Rx). In a point-to-point system, connect the optic in port A from the

first node to the optic in port A in the second node. Remember that the two fibers need

to be crossed, so that the laser output on one node is connected to the photodiode

input in the other node. This can be verified by observing the corresponding LEDs as

shown in the table below.

In a linear system, connect the fiber to Optic A in the end node (node with only one

fiber transceiver) to Optic B in the subsequent node. Repeat until the ‘headend’ node

is reached, where the fiber must go into Optic A .

In self-healing ring systems, simply connect Optic A from one node to Optic B on the

next node, throughout the ring.

** CAUTION:

Use caution when inserting it into a slot adjacent to an existing module. It is best to install this

module in your node first, to avoid potential damage to components on the back of this module.

*WARNING:

Insure main power is off when installing or removing.

Installing the Optical Transceiver Module

Point-to-Point Connect

Repeater Connect

Self-Healing Connect

Tx A

Rx A Tx A

Rx A

A8972FLC

A8974FLC

A8972FLC A8972FLC

Tx A

Rx A

HEAD END MIDDLE NODES FIELD END NODE

Tx B

Rx B

Tx A

Rx A

Tx A

Rx A

A8974FLC A8974FLC A8974FLC A8974FLC

Tx A

Rx A

Tx A

Rx A

Tx A

Rx A

Tx A

Rx A

Tx B

Rx B

Tx B

Rx B

Tx B

Rx B

Tx B

Rx B

LED operating status

Optic LED

RED Indicates faulty LASER or no module installed

OFF LASER operating within specifications

3. Verify fiber connectivity:

Using the LEDs on the back of the unit adjacent to the optic module, verify proper

operation as shown in the table below. Both optical launch power and optical receive

power, as well as transceiver status, can be verified from the LCD front panel.

GREEN Indicates sufficient power received and frame synchronization

OFF Indicates insufficient optical power

Setting Mode

8RS-485 2-wire 2 V

9RS-485 4-wire standard

ARS-485 4-wire 1 V

BRS-485 4-wire2V

CReserved

DReserved

EReserved

FTest Mode

Overview

The Phoenix A8910MPD data module is capable of inserting/extracting

4channels of multiprotocol serial data (MPD) per module. With a maximum of four

cards per node, the system capacity is 16 channels. Each channel is capable of

transmitting and receiving serial data throughout the Phoenix system. The card is not

limited to any single data type so that various formats can be mixed on a single card.

As with other GE Security MPD products, data translation capabilities are included.

Tools and materials required

The data modules are held in place with simple thumbscrews with screwdriver slots.

The only tool recommended is a small flat blade screwdriver.

Installation instructions:

1. Configuredata module:

Prior to installation, you must specify the appropriate data format using the rotary

switches on the module. For each channel on the data module, rotate the dial switch to

the desired format.If you want to select the data format from the front panel, leave the

switch in position 0.

Setting Mode

0Software-selectable (factorypreset)

1RS-232 (3-wire)

2RS-232 + handshake

3TTL

4RS-422 2-wire

5Manchester/biphase

6RS-485 2-wire standard/Sensornet

7RS-485 2-wire1V

NOTE: The DATA SELECT switches are shipped in the Software-Selectable setting.

As with all GE Security MPD products, data translation can easily

be accomplished using the table information below.

Translation Comment

Input

TTL RS-232, 3-wire

TTL RS-422

RS-232, 3-wire TTL

7-A

Signal level conversion.

Single ended to differential conversion.

Differential to single ended conversion.

RS232 Handshaking bit is used to indicate Tri-state.

Tri-state detection circuitry activates handshaking bit.

Output

7-A

RS-422 TTL-wire

RS-422 RS-232, 3-wire

RS-485 RS-232, 5-wire

RS-232, 5-wire RS-485

RS-232, 3-wireRS-422

Installing the Data Module

2. Install data module:

Up to four data modules can be installed in the Phoenix node.

From left, locate and insert data modules into slot 1, 2, 3, or 4

(color-keyed red) and secure.

3. Connect:

Each data module is shipped with (four) RJ45 cables and (four) breakout boxes to aid in

connecting to the Phoenix. Use the tables below to determine pinout information for

your application. GE Security recommends using shielded cable for all single ended

applications and twisted shielded cable for all differential formats. Wire gauge is

dependent on copper run length. Refer to manufacturer of data equipment for

specific recommendations. Once the data equipment has been connected, confirmation

of data activity can be verified on the front panel LCD.

The channel order is sequential, beginning with the top RJ45 in slot 1 as Channel 1,

working vertically such that the bottom RJ45 in slot 1 is Channel 4, and the top RJ45 in

slot 2 is Channel 5. This continues to the bottom RJ45 in slot 4, which is mapped to

Channel 16.

INSERT DATA CARDS IN SLOTS 1-4 (Red)

DATA EQUIPMENT FIBER LINK

DATA OUT

DATA IN

DATA OUT

Figure 1. Fiber Link Data Connections

Figure 1. Terminal Block Pin Assignments Figure 2. RJ45 Socket

(Viewed from the rear of the unit)

Using the breakout box

Abreakout box with a 3’ CAT 5 patch cord

(supplied) can be used to interface to the

Phoenix system. Pinouts are shown in the

tables and figures above.

RJ45-A

RJ45-B

RJ45-C

RJ45-D

Inhaltsverzeichnis

Andere GE Security Sicherheitssystem Handbücher

GE Security

GE Security Simon XT Benutzerhandbuch

GE Security

GE Security Simon XT Bedienungsanleitung

GE Security

GE Security 940 Bedienungsanleitung

GE Security

GE Security Simon 60-875 Bedienungsanleitung

GE Security

GE Security RLCDF Betriebsanleitung

GE Security

GE Security Simon Bedienungsanleitung

GE Security

GE Security CareGard Bedienungsanleitung

GE Security

GE Security CONCORD Bedienungsanleitung

GE Security

GE Security Concord 4 Bedienungsanleitung

GE Security

GE Security Simon XT V2 Bedienungsanleitung

GE Security

GE Security CS575 Benutzerhandbuch

GE Security

GE Security Concord 4 Bedienungsanleitung

GE Security

GE Security CareGard Bedienungsanleitung

GE Security

GE Security 60-792-01-95R Bedienungsanleitung

GE Security

GE Security Simon XT Bedienungsanleitung

GE Security

GE Security Simon Bedienungsanleitung

GE Security

GE Security Concord 4 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung