GE Security RLCDF Betriebsanleitung

Security

R Series Remote Annunciators

and Expander Installation and

Operation Guide

P/N 3100969 • REV 1.0 • ISS 15JUL08

This document may not be copied in whole or in part or otherwise reproduced

without prior written consent from GE Security, Inc., except where specifically

permitted under U.S. and international copyright law.

Document number: 3100969 Revision: 00.15

Disclaimer The information in this document is subject to change without notice.

GE Security, Inc. (“GE Security”) assumes no responsibility for inaccuracies or

omissions and specifically disclaims any liabilities, losses, or risks, personal or

otherwise, incurred as a consequence, directly or indirectly, of the use or application

of any of the contents of this document. For the latest documentation, contact your

local supplier or visit us online at www.gesecurity.com.

This publication may contain examples of screen captures and reports used in daily

operations. Examples may include fictitious names of individuals and companies.

Any similarity to names and addresses of actual businesses or persons is entirely

coincidental.

Trademarks and patents GE and the GE monogram are registered trademarks of General Electric Company.

The R Series Remote Annunciators and Expander name and logo are registered

trademarks of GE Security.

Other trade names used in this document may be trademarks or registered

trademarks of the manufacturers or vendors of the respective products.

Intended use Use this product only for the purpose it was designed for; refer to the data sheet and

user documentation for details. For the latest product information, contact your

local supplier or visit us online at www.gesecurity.com.

FCC compliance This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

You are cautioned that any changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority to operate the

equipment.

European Union directives

The European directive “Waste Electrical and Electronic Equipment” (WEEE) aims to

minimize the impact of electrical and electronic equipment waste on the

environment and human health. For proper treatment, recovery, and recycling, you

can return the equipment marked with this symbol to your local supplier upon the

purchase of equivalent new equipment, or dispose of it in designated collection

points. Further information can be found on the following website:

www.recyclethis.info.

European representative for manufacture (EMC): GE Security B.V., Kelvinstraat 7,

6003 DH Weert, The Netherlands.

R Series Remote Annunciators and Expander Installation and Operation Guide i

Content

Introduction to the R Series 1

Installation features and controls 1

Installing annunciators and expanders 3

Wiring diagrams 6

Troubleshooting 8

Specifications 9

Operating the LCD models 10

Operating the LED models 12

Reading LCD displays 14

System Normal screen 14

Event Message screen 14

Details screen 15

Entering a password 16

Message priorities 17

Index 19

R Series Remote Annunciators and Expander Installation and Operation Guide 1

Introduction to the R Series

The R Series Remote Annunciators and Expander provide remote

annunciation for fire alarm systems. The annunciators offer LCD or

LED annunciation, and can include common controls. The expander

uses LEDs.

The R Series includes three annunciator models and one expander

model. One or two expanders can be connected to any of the

annunciator models. Figure 1 shows the four models in the R Series.

Table 1 lists the features of each model. Table 2 is a complete list of

all models and accessories in the series.

Figure 1: Models in the R Series

Controls Enabled

Ack/Silence

Lamp Test

Power

Fire Alarm

Supervisory

Ground Fault

Trouble

RLCD

Controls Enabled

Ack/Silence

Reset

Signal Silence

Drill

Lamp Test

Power

Fire Alarm

Supervisory

Ground Fault

Trouble

RLCD-C

Controls Enabled

Ack/Silence

Reset

Signal Silence

Drill

Lamp Test

Power

Fire Alarm

Supervisory

Ground Fault

Trouble

RLED-C

RLED24

Table 1: Features of the models

Model LCD

Display

Zone

LEDs

Common

controls

System

LEDs

Buzzer

RLCD, RLCD-R, RLCDF Yes No No Yes Yes

RLCD-C, RLCD-CR, RLCD-CF Yes No Yes Yes Yes

RLED-C, RLED-CR, RLED-CF No 16 pairs Yes Yes Yes

RLED24, RLED24R No 24 pairs No No No

Introduction to the R Series

2 R Series Remote Annunciators and Expander Installation and Operation Guide

The annunciators and expanders can be mounted on a standard 4-

inch square electrical box, using the included mounting ring. They

can also be surface mounted in locking steel enclosures.

The annunciators communicate with the FACP on the RS-485 data

riser. This can be configured for Class A or Class B communication.

The annunciators do not provide ground fault isolation.

The annunciators are stand-alone units that can be powered by the

FACP or by an approved power supply.

Models with common controls can use a separate, remote key

switch to enable or disable the common controls.

Table 2: R Series models and accessories

Model number Description

RLCD Remote Annunciator: LCD text annunciator

without common controls. English.

RLCD-R Remote Annunciator: LCD text annunciator

without common controls. English. Red.

RLCDF Remote Annunciator: LCD text annunciator

without common controls. French.

RLCD-C Remote Annunciator:LCD text annunciator

with common controls. English.

RLCD-CR Remote Annunciator:LCD text annunciator

with common controls. English. Red.

RLCD-CF Remote Annunciator:LCD text annunciator

with common controls. French.

RLED-C Remote Annunciator: 16-pair LED zone

annunciator with common controls.

English.

RLED-CR Remote Annunciator: 16-pair LED zone

annunciator with common controls.

English. Red.

RLED-CF Remote Annunciator: 16-pair LED zone

annunciator with common controls. French.

RLED24 Remote Expander: 24-pair LED zone

expander with expander cable and zone

card insert.

RLED24R Remote Expander: 24-pair LED zone

expander with expander cable and zone

card insert. Red.

Model number Description

RA-ENC1 One-position enclosure for Remote

Annunciator.

RA-ENC2 Two-position enclosure for Remote

Annunciator and one Remote Expander,

including one interconnection cable.

RA-ENC3 Three-position enclosure for Remote

Annunciator and two Remote Expanders,

including two interconnection cables.

RKEY Remote key switch on plate for enabling or

disabling common controls (Lock/Unlock).

RA-LED16ZC Zone card insert for RLED-C, RLED-CR, and

RLED-CF.

RA-LED24ZC Zone card insert for RLED24, RLED24R.

Part number Description

27193-16 Electrical box, surface mount, white, single-

gang.

7300073 24-inch expander cable assembly, includes

cable and hardware.

7120313-01 12-inch expander cable (cable only).

7120313-02 24-inch expander cable (cable only).

R Series Remote Annunciators and Expander Installation and Operation Guide 1

Installation features and controls

Figure 2: Annunciator rear view showing terminals and controls

CH1 (+) IN

CH1 (-) IN

CH1 (+) OUT

24V (+) IN

24V (-) IN

CH1 (-) OUT

CH2 (+) IN

CH2 (-) IN

CH2 (+) OUT

CH2 (-) OUT

24V (+) OUT

24V (-) OUT

(

)

(

)

N/C

(

)

OUT

(

)

TX RX

RS-485 riser terminals

Communication LEDs

Mounting slot

DIP switch

Remote key switch terminals

Power terminals Expander cable terminals

Figure 3: Expander rear view showing terminals

(

)

OUT

(

)

V (-)

V (+)

Expander cable terminals

Mounting slot

Expander cable terminals

Table 3: DIP switch settings

Switch Description and values

S1 to S5 Network address. The annunciator network address (in binary).

The factory setting is for address 2. See Table 4 for examples.

S6 Network baud rate.

OFF = 9600 baud (factory default setting)

ON = 38,400 baud

S7 to S8 Not used

Installation features and controls

2 R Series Remote Annunciators and Expander Installation and Operation Guide

Table 4: Examples of DIP switch address settings

Address Settings Address

Settings

12345678

Installing annunciators and expanders

R Series Remote Annunciators and Expander Installation and Operation Guide 3

Installing annunciators and expanders

For correct operation, the annunciator must be configured with a

unique network address, must have the correct baud rate setting,

and must be in communication with the FACP.

If you are installing a Remote Annunciator and Remote Expanders in

enclosures RA-ENC2 or RA-ENC3, you must install the expanders

first. Refer to the installation sheets for the enclosures for the

correct sequence of steps.

If you are installing Remote Annunciators and Remote Expanders

using separate electrical boxes, the wire runs between the boxes

must be enclosed in conduit.

If you are installing a remote key switch, the switch must be located

within the enclosure, or within 20 feet (6.1 m) of the enclosure with

the cabling installed in conduit.

To install an annunciator:

1. Secure the mounting ring to the electrical box, as shown in

Figure 4.

2. Use the DIP switch to set the correct network address and baud

rate. See Table 3 for DIP switch settings.

3. Connect the RS-485 riser to the appropriate annunciator

terminals, as per Figure 5 (Class A) or Figure 6 (Class B).

Tip: Leave enough wire to remove and position the annunciator

when setting the DIP switch.

4. Attach the expander cable to the annunciator, if applicable. See

Figure 7.

5. Attach the remote key switch wiring to the annunciator, if

applicable. See Figure 8.

6. Tilt the annunciator up and slide the mounting slot onto the

onto the top flange of the mounting ring.

7. Tilt the annunciator down and push the bottom of the

annunciator over the stud-nut, as shown in Figure 4.

8. Secure the bottom of the annunciator to the mounting ring

using the captive screw.

9. Cover the screw hole with the product label plate.

Installing annunciators and expanders

4 R Series Remote Annunciators and Expander Installation and Operation Guide

To install an expander:

1. Complete and insert the zone card (labeling sheet) into the

expander.

2. Secure the mounting ring to the electrical box, as shown in

Figure 4.

3. Connect the expander cable to the expander. Attach an

expander cable for interconnection to a second expander, if

applicable. See Figure 7.

4. Tilt the expander up and slide the mounting slot onto the top

flange of the mounting ring.

5. Tilt the expander down and push the bottom of the annunciator

over the stud-nut, as shown in Figure 4.

6. Secure the bottom of the annunciator to the mounting ring

using the captive screw.

7. Cover the screw hole with the product label plate.

8. Repeat steps 1 through 7 for a second expander, if applicable.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere GE Security Sicherheitssystem Handbücher

GE Security

GE Security Simon XT Bedienungsanleitung

GE Security

GE Security 60-792-01-95R Bedienungsanleitung

GE Security

GE Security Simon Bedienungsanleitung

GE Security

GE Security Simon XT Bedienungsanleitung

GE Security

GE Security Concord 4 Bedienungsanleitung

GE Security

GE Security CareGard Bedienungsanleitung

GE Security

GE Security CS575 Benutzerhandbuch

GE Security

GE Security Concord 4 Bedienungsanleitung

GE Security

GE Security CONCORD Bedienungsanleitung

GE Security

GE Security Concord 4 Bedienungsanleitung

GE Security

GE Security Simon XT V2 Bedienungsanleitung

GE Security

GE Security CareGard Bedienungsanleitung

GE Security

GE Security 940 Bedienungsanleitung

GE Security

GE Security Simon 60-875 Bedienungsanleitung

GE Security

GE Security Phoenix A8950CC Bedienungsanleitung

GE Security

GE Security Simon XT Benutzerhandbuch

GE Security

GE Security Simon Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung