GE Security 60-597 Bedienungsanleitung

Page 1

HiTech Handheld Wireless Touchpad

HiTech Handheld

Wireless Touchpad

Document Number: 466-1012 Rev. B

November 1997

INSTALLATION

INSTRUCTIONS

Product Summary

The HiTech Handheld Wireless Touchpad is a pocket-

sized, lightweight, portable touchpad that uses ITI Learn

Mode™technology to control an ITI control panel.

The touchpad gives you the flexibility to arm and

disarm the system, bypass sensors, control lights, send

emergency alarms, and check the system’s status at your

convenience.

The touchpad features include the following:

νAutomatic Low battery reports to the panel

νRed/Green indicator light that responds differently

to regular keypresses and panic button keypresses

νPolice, Fire, and Auxiliary panic buttons

νAutomatic supervisory reports to the panel every 64

minutes

νLong life (5–8 years) 3 VDC lithium battery

νOperating temperature range: 10° to 120°F

νWall-mounting option

νLearn Mode technology makes panel programming

easy

νConvenient size and attractive style

νCompatible with all ITI Learn Mode panels,

including CareTaker®Plus, Commander 2000™,

Concord, and SX-V Special.

Installation Guidelines

Observe the following guidelines when using and

mounting the touchpad:

νRefer to the appropriate Reference Manual for

guidelines on typical range for using this and other

wireless devices.

νAvoid moist areas.

νAvoid excessive metal or electrical wiring, including

furnace and utility rooms.

νAvoid exceeding the touchpad’s operating

temperature limits of 10° to 120°F (-12.2° to 49°F)

Note: If the touchpad is wall mounted or always kept at

the installation site, set upper sensor number 89

to ON. If the touchpad will occasionally be

removed from the site (i.e. kept in an automo-

bile), set upper sensor number 89 to OFF.

Installing the Battery

To install the battery:

1. Remove the battery cover by pressing down on the

arrowhead and sliding it out (see Figure 1).

Figure 1. Removing the battery cover

123

OFF STAY AWAY

NO DELAY

CHIME

STATUS BYPASS

COMMAND

8341G02A.DS4

60-597

123

OFF STAY AWAY

NO DELAY

CHIME

STATUS BYPASS

COMMAND

8341G01A.DS4

Page 2

HiTech Handheld Wireless Touchpad

2. Drop the battery into the chamber with the knob

(+) end visible (see Figure 2).

Figure 2. Placing the battery in the chamber

3. Line up the battery cover’s two exposed tabs with

the seam of the touchpad’s front and back cover

(see Figure 3).

Figure 3. Lining up the battery cover

4. Press down on the cover and slide it into place.

5. If the red light turns on steady (indicating a power-

up trouble condition), remove the battery and rein-

stall it. Repeat until the red indicator light remains

off when the cover is replaced.

Adding the Touchpad to a Panel

Before the touchpad can communicate with a panel, you

must add the touchpad to panel memory.

To add the Touchpad to panel memory:

1. Refer to the appropriate panel’s installation instruc-

tions on “entering program mode” and “adding” or

“programming a wireless touchpad.”

2. Press BYPASS when the procedure prompts for the

touchpad activation.

Mounting the Touchpad

To mount the Touchpad:

1. Test the touchpad at the desired location before

mounting and evaluate the touchpad’s performance.

2. Secure the mounting bracket to the desired surface,

using the two screws from the accessory pack (see

Figure 4).

3. Place the bottom end of the touchpad into the bot-

tom of the mounting bracket and press the touchpad

into place (see Figure 5).

Testing the Touchpad

Remind the user to test their system and this touchpad

weekly. The Owner’s Manual describes how to test the

system.

To test the Touchpad after installation:

1. To avoid an emergency response, notify the central

station that you will be testing.

2. Arm and disarm the panel from various

points to determine the touchpad’s range in

the installation site.

Note: The green light flashes with each press of a num-

ber key or function key. The red/green light

flashes with each press of a panic button.

3. Press STATUS to check the current arming

level.

4. Bypass sensors using direct and indirect

bypass.

123

OFF STAY AWAY

NO DELAY

CHIME

STATUS BYPASS

COMMAND

8341G03A.DS4

123

OFF STAY AWAY

NO DELAY

CHIME

STATUS BYPASS

COMMAND

8341G04A.DS4

EXPOSED

TAB

TOUCHPAD

SEAM

EXPOSED

TAB

HiTech Handheld Wireless Touchpad

Page 3

5. Press and hold each panic button for two sec-

onds, until the red/green indicator light stops

flashing and the appropriate alarm sounds.

6. To mute the touchpad: press the 1 and 2but-

tons at the same time, until you hear confir-

mation beeps.

Press various buttons to test the mute feature.

7. Turn off mute by pressing the 1and 2 buttons

at the same time, until you hear confirmation

beeps.

8. Turn all lights on or off by pressing COM-

MAND + 0with the Security Pro 2000 or by

pressing LIGHTS-ON or LIGHTS-OFF twice

with the Security Pro 4000.

9. Turn individual lights on or off with the

Security Pro 4000 by pressing LIGHTS-ON or

LIGHTS-OFF + [unit number]. Unit numbers

range from 1 to 9.

Note: Refer to the appropriate

Owner’s Manual

for

instructions on using the touchpad with a specific

panel.

Specifications

Battery Power Supply: 3.0 VDC lithium battery

(operating life: 5-8 years). Use either a Duracell®

DL123A, Eveready®EL123A, Panasonic®CR123A, or

Sanyo®CR123A.

Note: The 5-8 year battery life has not been verified by UL.

Operating Temperature Range: 10° to 120°F

(-12.2° to 49°C)

Dimensions: 6.1” L x 2.1” W x 0.86” H

(15.49 cm x 5.33 cm x 2.18 cm)

Compatibility: All Learn Mode panels, including:

CareTaker®Plus, Concord, Commander 2000™, and SX-

V Special.

Note: The HiTech Touchpad controls lights differently

with various panels and software versions (see

Table 1).

Table 1. Touchpad Light Control

Panel COMMAND

+ 0

Light Buttons

On Off On/Off + n

Care-

Taker

Plus 3.0

✓✓✓✓*

Care-

Taker

Plus

1.0—2.1

✓✓†

Com-

mander

2000 4.0

✓

Concord ✓✓✓ ✓

SX-V

Special ✓✓ †

*Pressing the LIGHTS-ON and LIGHTS-OFF but-

tons followed by a unit number ncontrols the lights

assigned to unit number n. Unit numbers range

from 1 to 9.

†Pressing the LIGHTS-ON button toggles all lights

on or off, the same as pressing COMMAND + 0.

Page 4

HiTech Handheld Wireless Touchpad

FCC Notice

This device complies with FCC Rules Part 15. Operation is subject to the following two

conditions:

This device may not cause harmful interference.

This device must accept any interference that may be received, including interference

that may cause undesired operation.

Changes or modifications not expressly approved by Interactive Technologies, Inc. can

void the users authority to operate the equipment.

ITI, Commander 2000, SX-V, and CareTaker are registered trademarks of Interactive

Technologies, Inc. Learn Mode is a trademark of Interactive Technologies, Inc.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere GE Security Touchscreen Handbücher

GE Security

GE Security ATP2600 Bedienungsanleitung

Beliebte Touchscreen Handbücher anderer Marken

FlowLine

FlowLine Data loop Bedienungsanleitung

ALPEX

ALPEX AEx-8 P Series Bedienungsanleitung

Ltech

Ltech E5S Bedienungsanleitung

Harman

Harman AMX MODERO S MSD-701-L2 Bedienungsanleitung

Acnodes

Acnodes PC 1150 Bedienungsanleitung

AIS

AIS IP10IA99 series Bedienungsanleitung

IBASE Technology

IBASE Technology ASTUT-152-RE1S Bedienungsanleitung

YASKAWA

YASKAWA TP 610C Bedienungsanleitung

B&R

B&R Power Panel C Series Bedienungsanleitung

Beijer Electronics

Beijer Electronics X2 control Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT321W-521 Bedienungsanleitung

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Bedienungsanleitung

Qomo

Qomo QIT1386 Bedienungsanleitung

DFI

DFI KS104-CD Bedienungsanleitung

AMX

AMX AXP-PPC Leitfaden

Sartorius

Sartorius X3 PR 5410 Bedienungsanleitung

AMX

AMX Modero X Series Bedienungsanleitung

Advantech

Advantech TPC-30 Series Bedienungsanleitung