GE GE314 Bedienungsanleitung

OPERATING MANUAL

FINGERPRINTACCESS CONTROLLER

MODEL: GE314

Table of Contents

1. IMPORTANT SAFTY INSTRUCTIONS Page 4

2. INTRODUCTION Page 6

2.1 IDENTIFYING SUPPLIED PARTS Page 6

2.2 INTRODUCTION Page 6

2.3 FEATURES Page 6

2.4 SPECIFICATIONS Page 7

3. PRODUCT OVERVIEW Page 8

3.1 FUNCTIONS Page 8

3.2 PRODUCT EXPLANATION Page10

3.2.1 FRONT PANEL DESCRIPTION Page10

3.2.2 CONNECTOR LAYOUT Page11

3.2.3 WIRE COLOR TABLE OF THE GE314 Page11

4. INSTALLATION TIPS & CHECK POINT Page 12

4.1 CHECK POINT BEFORE THE INSTALLATION Page 12

4.1.1 CABLE SELECTION Page 12

4.1.2 CABLE SELECTION TABLE Page 13

4.2 CHECK POINT DURING THE INSTALLATION Page 13

4.2.1 TERMINATION RESISTOR Page 13

4.2.2 HOW TO CONNECT TERMINATION RESISTOR Page 14

4.2.3 GROUND SYSTEM Page 14

4.2.4 REVERSE DIODE CONNECTION Page 15

5. INSTALLATION Page 15

5.1 WALL MOUNT DRAWING Page 15

5.2 BACKUP BATTERY SWITCH Page 16

5.3 SYSTEM INITIALIZATION Page16

5.4 WALL MOUNT INSTALLATION Page 17

6. WIRING Page 17

6.1 POWER CONNECTION Page 17

6.2 INPUT CONNECTION Page 17

6.3 OUTPUT CONNECTION Page 18

6.4 EXTERNAL READER CONNECTION Page 18

6.5 RS232 PORT CONNECTION Page 19

6.6 RS485 PORT CONNECTION Page 20

6.6.1 RS485 CONNECTION (SINGLE UNIT) Page 20

6.6.2 RS485 CONNECTION (MUTIPLE UNITS) Page 20

6.7 TCP/IP CONNECTION (OPTIONAL) Page 21

7. BASIC SETTINGS Page 22

7.1 INITIALIZATION OF GE314 Page 22

7.2 HOW TO ENTER THE SETUP MENU Page 22

7.3 LANGUAGE SETTING Page 23

7.4 DATE/TIME SETTING Page 23

7.5 ID REGISTRATION Page 24

8. OPERATION Page 27

8.1 NORMAL OPERATION Page 27

8.2 DEFAULT SETTING Page 27

9. SETTING CHANGES Page 28

9.1 F1 SETUP MENU Page 29

9.2 F2 SETUP MENU Page 33

9.3 F3 SETUP MENU Page 37

9.4 F4 SETUP MENU Page 42

9.5 F5 SETUP MENU Page 47

9.6 F6 SETUP MENU Page 50

9.7 F7 SETUP MENU Page 53

9.8 F8 SETUP MENU Page 56

9.9 F9 SETUP MENU Page 59

APPENDIX Page 61

A. THE RELATION BETWEEN INPUT

AND OUTPUT (DEFAULT) Page 61

B. TROUBLE SHOOTING Page 63

FCC REGISTRATION INFORMATION Page 67

WARRANTY AND SERVICE Page 68

RMA REQUEST FORM & A/S REQUEST FORM Page 69

1. IMPORTANT SAFETY INSTRUCTIONS

To prevent injuries to persons and damages to property, please read all instructions and follow them

whenever you deal with this product.

After reading, please put this instruction manual where it can be easily seen for the system operator.

ON INSTALLATION AND POWER

Use 12V DC power ONLY.

- Connecting to higher than 12V DC may result in a risk of electric shock, fire, or heavy damage of the unit.

Do NOT install this product at places with wet or metallic dust or that can be watered.

- There may be risks of electric shock and fire.

Do NOT install this product near electric motors running.

- The Unit may not operate normally.

Do NOT set this product near heaters or any thing that produces heat.

- There may be a risk of fire.

Be ALWAYS careful not to short-circuit any part of the circuitry with tools like a screwdriver.

- There may be a risk of fire or heavy damage of the unit.

ON MAINTENANCE

Do NOT use any kind of liquid for cleaning.

- There may be a risk of electric shock, fire or heavy damage of the unit. Use air spray, if needed.

Users are cautioned NOT to attempt repair of this product or modify the wirings set by the installer at their own

discretion.

- It may pose the risk of fire, hardware damages, or abnormal operations of the unit.

It is recommended not to use a flammable spray or something else easy flammable near this product.

- There may be the risk of an explosion or fire.

Keep the unit away from any unauthorized people.

- It may cause abnormal operations of the unit.

NOTICE

Please contact a designated service center or the outlet at which the product was purchased when

A. Any liquid has been spilt or sprayed onto the product. In this case, cut the power off first.

B. The product seems to be operating abnormally.

C. The unit exhibits a distinct change in performance.

D. The unit has fallen to be broken down or damaged on its case.

* Repairing costs can be charged for troubles caused due to improper handling or negligence of users or the operator.

2. INTRODUCTION

2.1 IDENTIFYING SUPPLIED PARTS

Please unpack and check the contents of the box (Optional accessories, if purchased, may be included in the

package).

Main unit Wall mount Manual Diode

( 1ea ) ( 1ea ) ( 1ea ) ( 2개 )

2.2 INTRODUCTION

The GE314 is ideal to use for Single Door Access Control and Time & Attendance. The GE314 has four input

ports, two Form-C relay outputs, two TTL outputs, RS232/RS485 communication port and optional TCP/IP

communication port to meet various customer requirements. This user-friendly device allows you to register up

to 1,000 Fingerprint Users (Optional 2,000/4,000 Fingerprint Users) and can be stored up to 20,000 event

transactions. All Events can be uploaded and saved to the database of the host PC and the software creates the

report to MS-Excel, HTML and Text files for the Time & Attendance purpose. The GE314 has a built-in

Fingerprint Module, proximity card reader with IDC 26-bit Wiegand format and it has 24 keypads (10 Numeric

keys, 2 Control keys and 12 Function keys) for wide applications. The GE314 allows to accessing the door with

any combination of Fingerprints, Proximity Card/PIN and/or Password. The GE314 has four external input ports

to be connected to an exit button, motion detector, door contact sensor and existing alarm system to prevent

unauthorized access. The GE314 has a door relay to control the door lock and an alarm relay to warn any error.

The graphic LCD display supports 6 different languages so that the unit can be operated anywhere in the world.

All setup menus can be programmed through the front keypads or via Windows-based software program. The

GE314 is a cost effective biometrics system to be used for Standalone or network. Dual tamper switches prevent

unauthorized access.

2.3 FEATURES

 Dual function for Access Control and Time & Attendance

 8 bit and 16 bit Dual Microprocessors, 32 bit ARM9 Microprocessor for Fingerprint Module

 1,000 Fingerprint Users (Optional 2,000/4,000 Fingerprint Users) and 20,000 Event Buffers

 Built-in Fingerprint Scanner, Module and Algorithm

 Built-in Proximity Reader and External Reader Port for T&A

 24 Keypads including 12 Functional Keys

 Graphic LCD Display for 6 different Language Support

 Standalone or Network Communication via RS232/RS485 (max. 256ch)

 Optional TCP/IP Communication, Optional Automatic Touch Sensor (for Identification Mode)

 Independent 4 Inputs and 4 Outputs including 2 FORM-C Relay Outputs

 Output Time Setting for Individual ID(4 Levels – Longer Output Time for Handicap Person)

 Forced Door Open Alarm, Door Lock/Unlock by T/S and/or by registered ID

 Anti-pass Back, Duress Alarm Functions

 Dual Tamper Alarm

 10 Time schedules, 8 Days with 5 Individual Time intervals each

 10 Holiday Schedules, 100 holidays each

 Operating Mode Selectable for Individual ID (Proximity/PIN Only Mode, Fingerprints Only Mode,

Proximity/PIN + Fingerprints Mode, Proximity/PIN + Password + Fingerprints Mode)

 Time Schedule Applied to Individual ID, Input Port, Output Port and Reader Mode

 Multiple Master ID/Fingerprints Registration

 3 LED Indicators and Beeper for the System Status

2.4 SPECIFICATIONS

CPU 8 bit and 16bit Dual Microprocessors, 32bit ARM9 Microprocessor

Memory Program Memory: 2M bit ROM

Data Memory: 4M bit FLASH memory

Fingerprint Module: 1M bytes FLASH memory (Optional 2M/4M bytes)

Fingerprint User

Event Buffer

1,000 Fingerprint Users (Optional 2,000/4,000 Fingerprint Users)

20,000 Event Buffers

Operating Mode Operating mode can be programmed for Individual ID

- Proximity ID/PIN Only Mode

- Fingerprints Only Mode (Up to 500 Users only, Identification Mode)

- Proximity ID/PIN + Fingerprints(Password) Mode

- Proximity ID/PIN + Password + Fingerprints Mode

FAR (False Acceptance Rate) 0.001%

FRR (False Reject Rate) 0.1%

Fingerprint Scanner Optical Scanner, LED Lighting

Resolution of Scanner 500dpi, CMOS CCD, 356 x 292 pixels

1:1 Verification Time < 1 sec.

1:N Identification Time < 3 sec. if ID found (Up to 500 Fingerprints only)

Reader Port 1 Internal and 1 External Reader Port

Read Range Up to 4” (10cm) with IDC170 Clamshell Card

Reader Data Format Standard IDC 26 bit Wiegand Format

8 bit Burst Format for Keypad Reader

Communication port RS232/RS485(up to 256 channels) Address Selectable

9600(Default), 19200, 38400, 57600bps Communication Speed

Input/Output 4 Input Ports, Rating DC12V/ 20mA max.

2 Relay Outputs, DC12V~24V/ FORM-C Relay 2A max.

2 TTL Outputs, DC0 ~5V/ 20mA max.

Keypad 24 keys with Back lighting (Sky Blue)

- 10 Numeric Keys

- 2 Control Keys

- 12 Function Keys

Self Diagnostic Yes

Reset Power On Reset and Watch-dog Timer Reset

Operating Status 3 LED (Red, Green, Yellow) indicators, Beeper

Weight 1.62 lbs (735g)

Dimensions 7.56” x 6.42” x 1.97” (192mm x163mm x50mm)

LCD Display Module 128 x 64 dots, 2.85” x 1.56”(72.5mm x 39.5mm) View Area

Power DC 12V±10%, 550mA max.

Operating Environment 32°F ~ 149°F (0°C ~ +45°C), 0 ~ 90% Humidity None Condensing

Storage Environment -40°F ~ 158°F (-40 ~+70℃℃), 0 ~ 90% Humidity None Condensing

Mount Wall Mount or Electrical Gang Box Mount (U.S. and European/Asian)

Color Silver and Dark Gray Color

Optional

TCP/IP Module (Internal)

Connection

IIM7100A Internal Mounting Module for TCP/IP Communication

RJ45 Socket

Automatic Touch Sensor Capacitance Touch Sensor for Identification Mode only

Fingerprint Module 2,000 Fingerprint Module, 4,000 Fingerprint Module

3. PRODUCT OVERVIEW

3.1 FUNCTIONS

Stand-Alone Operation

The GE314 is capable of having 2 readers (1 Door Control). The unit receives card ID numbers from the

proximity readers and determines whether or not to unlock the door. When an input signal is entered, for

example from a Sensor activated or an Exit button pressed, the controller generates and logs an appropriate

response by input signals. All events are stored into the memory buffers and sent to the host computer. The

access controller is a true stand-alone device that, in the event of malfunction, will not affect other units when

used in conjunction with one another.

Operation with Host Computer

All event transactions can be managed via the host computer. The data transmitted from the controller can be

displayed and stored on the host PC.

Keypad

If the GE314 is not connected to a host PC, the integrated keypad and LCD display module can also be used

for the entire programming process.

Input/Output

The GE314 has 4 built-in inputs and 4 outputs (2 relay outputs and 2 TTL outputs) which can be used to

manipulate a wide variety of controls.

Time Schedule Setup

You can program 10 time schedules and apply one time schedule to each User. Each time schedule has 8

different time zones from Monday-Sunday (7 time zones) and one holiday. Each time zone has 5 different

time codes so you can program 5 different time codes to each day. You can also program time schedules for

individual inputs and outputs. Note that the time schedule for input is activated time code for input device so

that the input is activated during the time code on this time schedule. Each time schedule is linked to one

holiday schedule and this linked holiday only validates to the holiday time code of the time schedule.

Holiday Schedule Setup

Excepting Sunday, you can program 100 holidays to one holiday schedule. Each holiday schedule is linked to

one time schedule which has a time code for holidays. You can program all holidays to a holiday schedule

and the time code for holidays is programmed to the holiday time zone of time schedule.

Example: A. Holiday schedule 01 linked to time schedule 01,

Holiday schedule 02 linked to time schedule 02

B. Holiday schedule 02 linked to time schedule 01,

Holiday schedule 01 linked to time schedule 03

Forced Door Open Alarm

When the door is opened by force, the door contact sensor will be activated. For this application, you have to

install the door contact sensor and properly set the door contact time and outputs to the alarm devices. The

Forced Door Open Alarm will be generated until the alarm is cleared.

Overtime Door Open Alarm

The Overtime Door Open Alarm will be generated when the door is open continusly, after the door is opened

by corrected process.

The Overtime Door Open Alarm will be generated until the door is closed.

Anti-Pass-Back

By using an additional proximity reader, the Anti-Pass-Back mode can be set. The Anti-pass-back mode

prevents entry or exit when the registered user did not properly followed one entry and one exit by the Anti-

pass-back rule. The same user can not enter twice with the entry card without properly using the exit before.

Duress Alarm

In case of duress, enter the 2 digits Duress Password and press the<ENT> key before the normal access

process. The door can be opened as normal, but the duress alarm is also generated at the same time. The

duress alarm output will be activated to the TTL output and an alarm event will be sent to the host PC.

3.2 PRODUCT EXPLANATION

3.2.1 FRONT PANEL DESCRIPTION

LCD

System Operation

Status LED

Fingerprint

Scanner

24 key pad Function key

Figure: Description of GE314 Front Panel

LCD Module:

LCD module display GE314 status.

System Operation Status LED:

When the power is applied to GE314, the red LED is turned on.

When the Relay #1 is operated, the green LED is turned on.

When the Relay #2 is operated, the yellow LED is turned on.

24 key pad:

You can operate GE314 manually by using the key pad.

Function key:

The GE314 has 12 Function keys ([F1] ~ [F12]).

Inhaltsverzeichnis

Andere GE IP-Zugriffskontrollsysteme Handbücher

GE ATS125 Series Bedienungsanleitung

Beliebte IP-Zugriffskontrollsysteme Handbücher anderer Marken

ZKTeco

ZKTeco SpeedFace-V5L Bedienungsanleitung

Jantar

Jantar REX A-1-9 Bedienungsanleitung

2N Access Unit Merkblatt

Kedacom

Kedacom KSCA120 Series Bedienungsanleitung

H3C

H3C WX2880X Bedienungsanleitung

G4S

G4S S870-EX Leitfaden

PRASTEL

PRASTEL M2000PE Bedienungsanleitung

Allegion

Allegion interflex IF-281 Cylinder Bedienungsanleitung

TECOM

TECOM TS1067E Bedienungsanleitung

Fermax

Fermax Memokey 100C Benutzerhandbuch

Fermax

Fermax CITYLINE MEMOKEY Bedienungsanleitung

Software House

Software House iSTAR Pro 2U RM Bedienungsanleitung

AKCP

AKCP SP+ Bedienungsanleitung

Bpt

Bpt HNA/102 Bedienungsanleitung

Civintec

Civintec CV9601T-T-1F Bedienungsanleitung

BioMax

BioMax N-X90W Bedienungsanleitung

ZKTeco

ZKTeco OP-200 Bedienungsanleitung

FingerTec

FingerTec s-Kadex Bedienungsanleitung