GE Lumination Current LEL Series Bedienungsanleitung
1
Installation Guide
LEL Series - for HTEK/TEK Mounting
LuminationTM LED Luminaire
BEFORE YOU BEGIN
Read these instructions completely and carefully.
WARNING/AVERTISSEMENT
RISK OF ELECTRIC SHOCK
• Turn power off before inspection, installation or removal.
• Properly ground electrical enclosure.
RISK OF FIRE
• Follow all NEC or IEC local codes.
RISK OF INJURY
• Luminaire may fall down if not locked into mounting track
properly.
RISQUES DE DÉCHARGES ÉLECTRIQUES
• Coupez l’alimentation avant d’inspecter, installer ou déplacer le luminaire.
• Assurez-vous de correctement mettre à la terre le boîtier d’alimentation électrique.
RISQUES D’INCENDIE
• Respectez tous les codes NEC ou IEC ainsi que les et codes locaux applicables.
RISQUES DE BLESSURE
• Le luminaire pourrait tomber s’il n’est pas verrouiillé en place correctement aux
rails de montage.
Save These Instructions
Use only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.
Wear work gloves to prevent dirt and oil
from being transferred to the luminaire.
2
Track
Lock Lock
Mechanical xing knob
A
ON
OFF
B
1 2
0
Mechanical
xing knob
Circuit
selector knob
C
Luminaire Installation
Unpack unit from packaging. Properly inspect for
defects before installing.
RISK OF DAMAGE: Make sure the luminaire is only
carried out by holding two ends of gear box. Do
not touch the light guide when removing the xture
from the packaging or during the installation.
(A) On both adapters, rotate mechanical xing knob clockwise to ON position to lock xture to track.
(B) On adapter with metal pin on top, select the desired circuit with the circuit selector knob.
(C) For the dummy adapter without the metal pin, need to turn mechanical xing knob clockwise to the
cavity stopper as shown above.
CAUTION: Must turn mechanical xing knobs to the right position to prevent the luminaire from falling off
without locking.
Ensure alignment lines on luminaire and
adaptors are parallel and insert xture vertically
into track.
Track
Gearbox
Light guide
Dummy
adapter
Adapter with
metal pin
1
3
2
CAUTION
RISK OF DAMAGE
• Remove protective lm on Light Guide after installation.
• Do not touch Light Guide to avoid dirt, oil and ngerprints.
ATTENTION
RISQUE DE DOMMAGES
• Retirez le lm protecteur du luminaire après son installation.
• Ne touchez pas la surface émittrice du luminiaire pour éviter
les saletés, graisses ou empreintes digitales.
Cavity stopper
Dummy adapter
All trademarks are the property of their respective owners. Information provided is subject to
change without notice. All values are design or typical values when measured under laboratory
conditions. Current, powered by GE is a business of the General Electric Company.
© 2019 GE.
www.currentbyge.com IND314 (Rev 03/29/19)
Put the inter-connector on the top of two
luminaires, and make sure that the slot of the
inter-connector crosses the two end caps.
Inter-connector
Clips
Light Guide Clip
Push the inter-connector into the luminaires.
Remove the protective lm, and insert the Light
Guide clip between the two Light Guides.
1 2
Luminaire Inter-connection & Alignment (Continuous Mounting)
Luminaire Removal
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation. CAN ICES-005 (A) / NMB-005 (A)
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own
expense.
To remove xture put Circuit Selector to 0 and Mechanical Knob to off. Then, while tilting xture, remove luminaire
marked side rst. Carefully check the clips are still in the right positions after removing the protective lm. If the clips fall
down, need push them back to the right positions.
Andere GE Laterne Handbücher
GE
GE Lumination LDXB Series Bedienungsanleitung
GE
GE IP140 Series Bedienungsanleitung
GE
GE Evolve Bedienungsanleitung
GE
GE Currnet Evolve ECLS Bedienungsanleitung
GE
GE Lumination LRC Series Bedienungsanleitung
GE
GE High Mast Luminaire Bedienungsanleitung
GE
GE Lumination RC Series Bedienungsanleitung
GE
GE Lumination LRX Series Bedienungsanleitung
GE
GE Zoneline 1000 Series Bedienungsanleitung
GE
GE IP180 Series Bedienungsanleitung
GE
GE GRT Series Bedienungsanleitung
GE
GE Current Lumination IS Series Bedienungsanleitung
GE
GE LED Mariner Start Konfigurationshandbuch
GE
GE Current Lumination LRXB Series Bedienungsanleitung
GE
GE Lumination LUR Series Bedienungsanleitung
GE
GE Lumination LPL GenB Series Bedienungsanleitung
GE
GE Wallmount 175 Luminaire Bedienungsanleitung
GE
GE Lumination DS Series Bedienungsanleitung
GE
GE Decashield 400 Bedienungsanleitung
GE
GE Arize H1000 Bedienungsanleitung
