GE Spacemaker WSM2780 Bedienungsanleitung

WARNING – POTENTIAL FIRE AND SHOCK HAZARD

• Use only rigi metal or flexible metal 4″iameter uctwork insi e the ryer cabinet or for exhausting to the outsi e.

Use of plastic or other combustible uctwork can cause a fire. Foil or other easily puncture uctwork can cause a fire

if it collapses or becomes restricte in use or uring installation.

• This appliance must be properly groun e an installe as escribe in these instructions.

Installation instructions Spacemaker™

for your new Laundry

WSM2780 Gas

Before you egin – Read these instructions completely and carefully.

IMPORTANT – OBSERVE ALL GOVERNING CODES AND ORDINANCES.

Note to Installer – Be sure to leave these instructions with the Consumer.

Note to Consumer – Keep these instructions with your Owner’s Manual for future reference.

TOOLS NEEDED

• Slip joint pliers

• Phillips-head and flat-blade screwdrivers

• Ratchet with 3/8″socket

• Carpenter’s level

• Adj stable wrenches

• Pipe thread sealer

49-90331

09-07 JR

134923400 (0907)

Printed in the United States

IMPORTANT

• Exha sting the dryer to the o tside is req ired to

prevent large amo nts of moist re, lint and other

prod cts of comb stion from being blown into the

room.

• Service information and a wiring diagram are located

in the dryer access panel.

PRODUCT DIMENSIONS

731⁄2″

545⁄16″

33⁄4″

27″

Drain o tlet

(rear)

Water

inlets (rear)

Vent

Gas s pply

pipe (rear)

93⁄8″

51⁄4″

297⁄16″

411⁄4″

43″

251⁄4″

161⁄4″

21⁄2″

47″

17⁄8″

413⁄16″

117⁄16″

361⁄16″

3013⁄16″

51°

CONTENTS

Installation Proced re . . . . . . . .page 2

Pl mbing Information . . . . . . . .page 5

Electrical Information . . . . . . . . .page 5

Gas Information . . . . . . . . . . . . .page 6

Exha st Information . . . . . . . . . .page 6

Mobile Home Installation . . . . .page 7

Alcove or

Closet Installation . . . . . . . . . . . .page 7

Door Ventilation Opening . . . . .page 8

Miscellaneo s

Req irements . . . . . . . . . . . . . . . .page 8

PREPARING DRAIN HOSE

Form a “U” shape on the end of the drain hose with

the hose pointed toward the drain.

For an installation req iring a longer drain hose,

se the WH41X312 extra-long (108″) drain hose.

Attach to the machine in the same manner as the

original hose.

UNPACKING SPACEMAKER™

Remove tape and two corner pads from rear

bottom corners of appliance.

Using the fo r shipping corner posts, lay the

appliance on its left side so the shipping base does

not rest on the floor.

Remove the foam shipping pad.

Remove the washer shipping bolt sing the ratchet

with 3/8″socket and remove the plastic spacer

block sing the slip joint pliers.

Ret rn the appliance to the pright position and

locate it in the general area to be installed. Provide

eno gh space at the rear for installing the water

inlet hose.

Untape and open washer lid.

Remove:

a. foam t b blocking pad

b. foam shipping blocks from rear of nit

c. tape from dryer door

. foam dryer s pport pads

e. inlet hoses

f. From the back of the washer, remove the wire

shipping clips sec ring the drain hose. Plastic

clamps sec re the drain hose to the right side

of the washer backsheet. These clamps form a

standpipe to prevent water siphoning. DO NOT

REMOVE THESE CLAMPS.

Plastic spacer

block

Installation Instructions

T b

blocking pad

Shipping

blocks Shipping

clips Rear vent

only

Drain hose

Shipping carton

corner posts

Foam

shipping pad

Mechanism

shipping bolt

Dryer

s pport pads

UNPACKING SPACEMAKER™ (CONT.)

NOTE:

The t b blocking pad, shipping bolt and plastic

spacer sho ld be retained for se if the appliance is

transported at a later date.

Remove clips holding the following:

a. inlet hoses

b. drain hose

c. power cord

CONNECTING TO PLUMBING FACILITIES

CAUTION: Be sure water supply lines have been

thoroughly flushe to remove particles that might

clog the washer filter screens.

Check inlet hoses to ins re the r bber washers

are installed in each end. (If yo r la ndry center

has the hoses attached to the water valve,

proceed to Step 13A.) Caref lly connect the inlet

hoses to the water valve (on the left side of the

washer cabinet), tighten by hand, then tighten

another 2/3 t rn with pliers.

CAUTION: DO NOT CROSS THREAD OR

OVERTIGHTEN THESE CONNECTIONS.

Determine which water fa cet is the HOT water

fa cet and caref lly connect the bottom inlet

hose to the HOT water fa cet, tighten by hand,

then tighten another 2/3 t rn with pliers.

Caref lly connect the top inlet hose to the

COLD water fa cet, tighten by hand, then

tighten another 2/3 t rn with pliers.

CAUTION: DO NOT CROSS THREAD OR

OVERTIGHTEN THESE CONNECTIONS.

T rn the water on and check for leaks

at both connections.

Place formed end of drain hose in drain facility

and sec re with cable tie (provided in literat re

package).

NOTE:

Drain hose MUST be sec red to drain facility in

all cases.

13B

13A

MOVING SPACEMAKER™TO OPERATING

LOCATION

Remove the 2 screws sec ring the access panel

to the dryer cabinet. Lift the front access panel

ntil the tabs can be disengaged from the dryer

cabinet and remove the panel.

Ro te the inlet hoses, drain hose and power cord

thro gh the rear access area for temporary

holding when moving the appliance to the

operating location.

To ens re the La ndry Center is level and solid

on all fo r legs, tilt the La ndry Center forward

so the rear legs are off the floor. Gently set the

La ndry Center back down to allow the rear legs

to self adj st. Place a level on top of the washer.

Check it side to side, then front to back. Screw

the front leveling legs p or down to ens re the

La ndry Center is resting solid on all fo r legs

(no rocking of the La ndry Center sho ld exist).

NOTE:

Keep the leg extension at a minim m to prevent

excessive vibration.

11A

Access panel

screws

Installation Instructions

Cord length

4 ft.

Cable tie

33″Min./

96″Max.

Installation Instructions

CONNECTING TO GAS SUPPLY

Connect the gas s pply to the dryer. If codes

allow, se new flexible metal t bing (design

certified by the American Gas Association). Be

s re there are no kinks. For gas connections, yo

MUST se pipe joint compo nd resistant to the

action of LP gas.

CAUTION: Be sure electricity is OFF at power

supply source (circuit breaker/fuse box).

Pl g power cord into electrical o tlet.

IMPORTANT:

120 volt 60 hz AC only electrical s pply is

req ired on a separate 15 ampere circ it f sed by a time

delay f se or circ it breaker.

14A

NOTE: Do not, un er

any circumstances,

remove groun ing

prong from plug.

Gro nding

prong

FINAL APPLIANCE LEVELING

CAUTION: ALL WEIGHT MUST BE REMOVED FROM

APPLIANCE LEVELING LEG WHILE ADJUSTING.

THREADS ON LEG WILL BE DAMAGED OTHERWISE.

Again, make s re the appliance rests firmly on

all fo r legs. No rocking of the appliance sho ld

exist.

CHECKING APPLIANCE OPERATION

Make s re all packing and shipping materials are

removed, incl ding the washer shipping bolt and

plastic spacer block.

Make s re the drain hose is properly ro ted—not

coiled or kinked.

Make s re water inlet hoses are connected (HOT

to HOT) and tightened sec rely witho t kinks.

T rn on water fa cets and check for leaks.

Tape all joints to make s re exha st d ctwork is

sec red witho t leaks.

T rn on electricity at the power so rce.

T rn on the washer and dryer and r n thro gh

one cycle. Check all hoses for leaks. Ens re the

b rner has lit.

NOTE:

Before the b rner will light, it is necessary for

the gas line to be bled of air. If the b rner does not light

within 45 seconds the first time the dryer is t rned on,

the safety switch will sh t off the b rner. If this happens,

t rn the timer to “OFF” and wait 5 min tes before

making another attempt to light.

17D

17C

17B

17A

REPLACING FRONT ACCESS PANEL

Reinstall the safety cover and front access panel.

Place the Owner’s Man al and Installation

Instr ctions in a location where they can be fo nd

by the c stomer.

Installation Instructions

PLUMBING INFORMATION

WATER SUPPLY REQUIREMENTS

• HOT AND COLD WATER FAUCETS – M st be within 42″

of the appliance water inlet hose connections. The

fa cets m st be 3/4″ garden hose-type so inlet

hoses can be connected.

• WATER PRESSURE – M st be between 10 and 120

po nds per sq are inch with a maxim m nbalance

press re, hot vs cold flowing, of 10 po nds per

sq are inch.

• SHUT-OFF VALVES – Both hot and cold water sh t-off

valves (fa cets) sho ld be s pplied.

• LOCATION – Do not install appliance in an area where

the temperat re will fall below freezing. If appliance is

stored or transported in freezing temperat res, be s re

all water from the fill and drain systems has been

removed.

DRAIN REQUIREMENTS

• DRAIN RATE – The drain or standpipe m st be capable

of accepting a discharge at the rate of 16 gallons per

min te.

• DRAIN HEIGHT – The drain height m st be 33″

minim m and 96″maxim m.

• STANDPIPE DIAMETER – The standpipe diameter m st

be 1″minim m. There MUST be an air gap aro nd the

drain hose in the standpipe. A sn g fit can ca se a

siphoning action.

• SIPHON BREAK KIT – For a drain facility less than 33″

high, the hose, co pling and clamps provided in the

machine m st be sed and, in addition, a siphon break

MUST be installed on the back of the machine. Use

Siphon Break Kit WH49X228 and FOLLOW

INSTRUCTIONS IN THE KIT.

ELECTRICAL CONNECTION

INFORMATION

CAUTION:

For personal safety:

TURN OFF ELECTRICITY AT POWER SOURCE (CIRCUIT

BREAKER/FUSE BOX) BEFORE INSTALLING OR

SERVICING THIS APPLIANCE.

DO NOT USE AN EXTENSION CORD WITH THIS

APPLIANCE.

THIS APPLIANCE MUST BE PROPERLY GROUNDED.

This appliance m st be electrically gro nded in

accordance with local codes and ordinances, or

in the absence of local codes, in accordance with the

NATIONAL ELECTRICAL CODE, ANSI/NFPA NO. 70-1987.

ELECTRICAL REQUIREMENTS

• This appliance sho ld be connected to an individ al

branch circ it with 120 volt single-phase 60 Hz

electrical service and sho ld be protected by 15 amp.

time-delay f ses or circ it breakers.

EXHAUST

EXHAUST DUCT LENGTH INFORMATION

• The MAXIMUM ALLOWABLE length of the exha st

system depends pon the type of d ct, n mber of

t rns, the type of exha st hood (wall cap) and all

conditions noted below. The maxim m allowable length

for both rigid and flexible metal is shown in the table

below. More than three 90° t rns are not

recommended.

HOOD OR WALL CAP

• Terminate in a manner to prevent back drafts or entry

of birds or other wildlife.

• Termination sho ld present minimal resistance to

the exha st airflow and sho ld req ire little or no

maintenance to prevent clogging.

• Never install a screen over the exha st d ct.

• Wall caps m st be installed at least 12″above

gro nd level or any other obstr ction with the

opening pointed down.

• If roof vents or lo vered plen ms are sed, they m st

be eq ivalent to a 4″dampered wall cap in regard to

resistance to airflow, prevention of back drafts and

maintenance req ired to prevent clogging.

TURNS OTHER THAN 90°

• One t rn of 45° or less may be ignored.

• Two 45° t rns sho ld be treated as one 90°.

NUMBER EXHAUST

OF 90° HOOD TYPE

TURNS A B

0 46 ft. 37 ft. Maxim m length of 4″

1 38 ft. 30 ft. diameter rigid metal d ct

2 31 ft. 22 ft.

3 24 ft. 15 ft.

0 30 ft. 24 ft. Maxim m length of 4″

1 25 ft. 20 ft. diameter flexible metal

2 20 ft. 14 ft. d ct

3 16 ft. 10 ft.

Installation Instructions

GAS CONNECTION INFORMATION

CAUTION:

Do not attempt to alter gas orifice or a just burner air

shutter. Nat ral gas inp t may vary in some areas from

700 to 1200 B.T.U. per c bic foot. If the gas orifice or

b rner air sh tter is incorrectly adj sted, serio s

personal inj ry and/or fire hazard can occ r. Yo r local

gas company will know the q alities of the gas in yo r

area. Contact your local servicing ealer if burner

a justment or orifice changes are necessary.

Do not use an open flame for leak testing. Serio s

personal inj ry and/or a fire hazard can res lt if an open

flame is sed to test for gas leaks. Use a soap an water

solution to test all gas line fittings.

Do not install the Laun ry Center to an L.P. gas supply

without installing conversion kit. All La ndry Centers

are shipped with a press re reg lator and nat ral gas

orifice. Using a nat ral gas orifice with an L.P. gas s pply

can res lt in personal inj ry, clothes damage and/or a

fire hazard. Have a qualifie gas technician install a

conversion kit in the Laun ry Center before use.

• Installation m st meet American National Standard,

National F el Gas Code ANSI Z 223 1—1988 and local

codes and ordinances.

• The gas s pply line sho ld be a 1/2″pipe. A 1/2″to

3/8″red cer m st be sed to connect the dryer to

the s pply line.

• The gas s pply line m st have a sh t-off valve

preferably within six feet of the dryer.

• A 1/8″NPT pl gged tapping, accessible for test ga ge

connection, m st be installed immediately pstream

of the gas s pply connection.

4″

21⁄2″

Rear vent only

Installation Instructions

EXHAUST (CONT.)

SEALING OF JOINTS

• All joints sho ld be tight to avoid leaks.

NOTE:

The male end of each section of d ct m st point

away from the dryer.

• Do not assemble d ctwork with fasteners that

extend into the d ct. They will serve as a collection

point for lint.

• D ct joints can be made air- and moist re-tight by

wrapping the overlapped joints with d ct tape.

INSULATION

• D ctwork that r ns thro gh an nheated area or is

near an air conditioning d ct sho ld be ins lated to

red ce condensation and lint b ild p.

PARTS AVAILABLE FROM LOCAL SERVICE

ORGANIZATIONS

• Rigid Metal D ct Components

WX8X63 4″x 1′D ct

WX8X64 4″x 2′D ct

WX8X51 4″Elbow

WX8X59 4″Al min m Hood

• Flexible Metal D ct Components

Kit WX8X66—7′Al min m d ct, 4″hood and 2 clamps

WX8X65 7′Al min m Flexible D ct

WX8X58 4″Clamps (2)

WX8X59 4″Al min m Hood

MOBILE HOME INSTALLATION

• Installation m st conform to Man fact red Home

Constr ction and Safety Standard, Title 24 CFR,

Part 32-80.

• The dryer m st be exha sted to the o tside with

the termination sec rely fastened to the mobile

home str ct re.

• The exha st MUST NOT be terminated beneath the

mobile home.

• The exha st d ct material MUST NOT s pport

comb stion.

CONSIDERATION MUST BE GIVEN TO PROVIDE ADEQUATE

CLEARANCES FOR INSTALLATION AND SERVICE.

ALCOVE OR CLOSET INSTALLATION

• If yo r dryer is approved for installation in an alcove

or closet, it will be stated on a label on the back of

the dryer.

• TO PREVENT LARGE AMOUNTS OF LINT AND MOISTURE

FROM ACCUMULATING AND TO MAINTAIN DRYING

EFFICIENCY, THIS MACHINE MUST BE EXHAUSTED

OUTDOORS.

• DO NOT install this appliance with less than

the minim m clearances shown above.

CONSIDERATION MUST BE GIVEN TO PROVIDE ADEQUATE

CLEARANCES FOR INSTALLATION AND SERVICE.

CAUTION: DO NOT INSTALL THIS APPLIANCE IN A CLOSET

WITH A SOLID DOOR.

1″

0″

0″0″

60 Sq. In.

Installation Instructions

DOOR VENTILATION OPENING

A minim m of 120 sq are inches of opening, eq ally

divided at top and bottom, is req ired. Air openings are

req ired to be nobstr cted when a door is installed.

A lo vered door with eq ivalent air openings for the

f ll length of the door is acceptable.

When lo vers or registers are placed in door openings,

the free air openings of the lo vers or registers m st

eq al 120 sq are inches.

60 Sq. In.

WARNING –

For your safety, the information in this manual must

be followe to minimize the risk of fire or explosion or to

prevent property amage, personal injury or loss of life.

• Do not store or use gasoline or other flammable vapors

an liqui s in the vicinity of this or any other appliance.

• WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; o not use any

phone in your buil ing.

• Clear the room, buil ing or area of all occupants.

• Imme iately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire

epartment.

Installation an service must be performe by a qualifie

installer, a service agency or the gas supplier.

MISCELLANEOUS REQUIREMENTS

LOCATION

• The appliance m st be installed on firm flooring to

minimize vibration d ring spin cycles. Concrete flooring

is best; b t wood base is s fficient, providing the floor

s pport meets FHA standards.

• The appliance sho ld not be installed on r gs or

exposed to the weather.

Andere Handbücher für Spacemaker WSM2780

Inhaltsverzeichnis

Andere GE Waschmaschine Handbücher

GE Spacemaker WSM2780 Bedienungsanleitung

GE FPDW Bedienungsanleitung

GE WSM2700WWW - 27" Unitized Spacemaker Washer Bedienungsanleitung

GE Spacemaker WSM2480 Bedienungsanleitung

GE Spacemaker WSM2000H Montageanleitung

GE Spacemaker WSM2780 Bedienungsanleitung

GE Unitized Spacemaker WSM2420 Bedienungsanleitung

GE Spacemaker WSM2700R Bedienungsanleitung

GE Spacemaker WSM2420S Bedienungsanleitung

GE Spacemaker WSM2700 Bedienungsanleitung

GE Spacemaker WSM2780 Bedienungsanleitung

GE Spacemaker WSM2700L Bedienungsanleitung

GE Spacemaker GTUP270EMWW Anleitung zur Verwendung

GE Spacemaker WSM2700 Bedienungsanleitung

GE Spacemaker Laundry WSM27TH Bedienungsanleitung

GE Spacemaker WSM2700 Bedienungsanleitung

GE Spacemaker WSM2780 Bedienungsanleitung

GE Spacemaker WSM2420S Bedienungsanleitung

GE 49-90280 Bedienungsanleitung

Beliebte Waschmaschine Handbücher anderer Marken

LAUNDRY JET

LAUNDRY JET Plus Bedienungsanleitung

LG WKGX301H A Series Bedienungsanleitung

Kenmore

Kenmore Kenmore 27" Wide LAUNDRY CENTER Washer -... Bedienungsanleitung

LG WK X30 Series Bedienungsanleitung

Frigidaire

Frigidaire GLEH164DS1 Administratorhandbuch

Frigidaire

Frigidaire GLEH1642DS0 Administratorhandbuch

AEG

AEG LAVATHERM 65280AC Bedienungsanleitung

Samsung

Samsung WF0500NXWG Bedienungsanleitung

Whirlpool

Whirlpool WVP5000SQ0 Bedienungsanleitung

Whirlpool

Whirlpool XVP8600TB0 Bedienungsanleitung

Frigidaire

Frigidaire MEX731CFS2 Bedienungsanleitung

Asko

Asko Washer/Dryer Combination Laundry System Bedienungsanleitung

Aerus

Aerus LAUNDRY PRO Bedienungsanleitung

Frigidaire

Frigidaire FLCE752CAW Betriebsanleitung

Mustee

Mustee UTILATUB 17F Bedienungsanleitung

Whirlpool

Whirlpool XVP9000TA0 Bedienungsanleitung

Frigidaire

Frigidaire GLGT1142CS1 Kurzanleitung

LAUNDRY JET

LAUNDRY JET ISense Bedienungsanleitung