GE Albeo ABR2 Bedienungsanleitung

ALB019

Albeo®ABR2 LED Luminaire

Heavy Industrial High Bay Lighting

BEFORE YOU BEGIN

Read these instructions completely and carefully.

Save these instructions for future use.

Installation Guide

ALB019

Risk of electrical shock. Turn power off before inspection, installation or

removal. Properly ground electrical enclosure.

Risk of re. Follow all NEC and local codes. Use only UL or IEC approved

wire for input/output connections. Minimum size 18 AWG.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that may cause undesired operation. CAN ICES-005 (A) / NMB-005 (A)

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Risgues de décharges électriques.

Coupez l’alimentation avant d’inspecter,

installer ou déplacer le luminaire. Assurez-vous de correctement mettre à

la terre le boîtier d’alimentation électrique.

Risque d’incendie. Respectez tous les codes NEC et codes locaux.

N’utilisez que des ls approuvés par UL ou IEC pour les entrées/sorties de

connexion. Taille minimum 18 AWG.

WARNING/AVERTISSEMENT/ADVERTENCIA

Save These Instructions

Use only in the manner intended by the manufacturer.

If you have any questions, contact the manufacturer.

Prepare Electrical Wiring

Electrical Requirements

The LED driver must be supplied with 120-277 VAC or 347/480

VAC, 50/60 Hz per productlabel and connected to an individual

properlygrounded branch circuit, protected by a 15 or 20ampere

circuit breaker.

Grounding Instructions

The grounding and bonding of the overall system shall be done

in accordance with National Electric Code (NEC) Article 600 and

local codes.

Installation GuideAlbeo®ABR2 LED Luminaire

Carefully unpack unit and properly inspect

for defects before installing. Wear work

gloves to prevent dirt and oil from being

transferred to the luminaire.

Provide at least 12” of clearance from the top of the xture to any ceiling or surface above.

NOTE: The standard conguration uses a 3-conductor SOOW cable. The dimming option utilizes a 5-conductor SOOW cable for both AC

and 0-10V control wires.

NOTE: For applications requiring the “R” corrosion resistant nish, use mounting hardware appropriate for the environment.

Please follow all UL, NEC and minimum load rating guidelines when selecting and installing a cable or chain.

NOTE: When selecting chain, a joint in a circular chain link shall be welded. A joint in a chain link of another shape shall not be located

within 30 degrees of the vertical unless welded.

Hang two chains/cables from a structural member of the ceiling. Fixture must be supported independently of an outlet box. Loop chain/

cable through the mounting slots next to each xture end. Chain/cable mounting locations must be in the slots at the ends of the xture.

Secure two 1/2” threaded rods into structural members in ceiling. Place a nut on each threaded rod where xture should hang. Slide rod

mount brackets onto threaded rods and tighten second nut onto rods to secure xture.

NOTE: Safety chains can be used in mounting slots at end of xture.

Section 1: Unit Installation

Section 2: Chain or Cable Mounting

Section 3: Threaded Rod Mounting

Choose a mounting method: chain or cable,

rod mount, or pendant mount.

Wire colors:

Fixture Weight

ABR2-Series Max. Weight (lbs.)

120/277VConfiguration 347/480V

Single 21 23

Dual 45 49

BlackLive

White Neutral

Green Safety Ground

Purple0-10V (+)

Gray 0-10V (–)

Fixture Weight

ABR1-Series Max. Weight (lbs.)

120/277VConfiguration 347/480V

Single 21 23

Dual 45 49

BlackLive

White Neutral

Green Safety Ground

Purple0-10V (+)

Gray 0-10V (–)

Dual FixtureSingle Fixture

Attach to

structural

member

Fasten

with nuts

Attach to

structural

member

Attach to

structural

member

Single Fixture

See Note See Note

Dual Fixture

Dual FixtureSingle Fixture

Attach to

structural

member

Fasten

with nuts

Attach to

structural

member

Attach to

structural

member

Single Fixture

See Note See Note

Dual Fixture

Installation GuideAlbeo®ABR2 LED Luminaire

Section 4: Pendant Mounting

AC power cord

Tighten

screw

Black To AC Main

White

Green

Purple (+)

Gray (-)

Line

Neutral

Ground

0-10V(+)

0-10V(-)

To 0-10V

Dimmer

LED Driver

AC power cord

Tighten

screw

Black To AC Main

White

Green

Purple (+)

Gray (-)

Line

Neutral

Ground

0-10V(+)

0-10V(-)

To 0-10V

Dimmer

LED Driver

AC power cord

Tighten

screw

Black To AC Main

White

Green

Purple (+)

Gray (-)

Line

Neutral

Ground

0-10V(+)

0-10V(-)

To 0-10V

Dimmer

LED Driver

AC power cord

Tighten

screw

Black To AC Main

White

Green

Purple (+)

Gray (-)

Line

Neutral

Ground

0-10V(+)

0-10V(-)

To 0-10V

Dimmer

LED Driver

AC power cord

Tighten

screw

Black To AC Main

White

Green

Purple (+)

Gray (-)

Line

Neutral

Ground

0-10V(+)

0-10V(-)

To 0-10V

Dimmer

LED Driver

AC power cord

Tighten

screw

Black To AC Main

White

Green

Purple (+)

Gray (-)

Line

Neutral

Ground

0-10V(+)

0-10V(-)

To 0-10V

Dimmer

LED Driver

Attach pendant mount box to ¾” NPT

conduit.Determine rotation of xture

and lock orientation in place with provided

set screw.

Swing xture closed and secure with the

slide clip. Lock slide clip in place with screw.

Secure pendant mount box to xture by fully tightening the captive screws on the sides of the pendant mount box to the xture.

NOTE: Safety chains can be used in mounting slots at end of xture.

Single Fixtur

ual Fixture

See

Note

See

Note

Captive screws Captive screws

3”

12”

1/2” bolts

Safety chain

Lift xture up and hang on pendant mount

box using hinge piece.

Connect the green (ground), black (line)

and white (neutral) wires of the AC line to

the similarly colored wires of the xture’s

power cord using UL listed wire connectors.

Close junction box.

Feed the AC power cord through the

conduit and into the junction box.

The 0-10V dimming option uses a 5-conductor

SOOW cable. Install cable per NEC and local

codes. For pendant mount option, cord can

be run through 1/2” NPT hole on top of the

mount box.

A 10V signal corresponds to 100% lumen

output. A 0V signal corresponds to ~10%

lumen output. Shorting the dimming wires

dims the xture to ~10% lumen output.

Installation GuideAlbeo®ABR2 LED Luminaire

Single FixtureDual Fixture

See

Note

See

Note

Captive screws Captive screws

3”

12”

1/2” bolts

Safety chain

Single FixtureDual Fixture

See

Note

See

Note

Captive screws Captive screws

3”

12”

1/2” bolts

Safety chain

Single FixtureDual Fixture

See

Note

See

Note

Captive screws Captive screws

3”

12”

1/2” bolts

Safety chain

Single FixtureDual Fixture

See

Note

See

Note

Captive screws Captive screws

3”

12”

1/2” bolts

Safety chain

Mount U-bracket to a at wall or ceiling

surface using (2) 1/2” bolts. Use either the 3”

or the 12” hole pattern.

Section 5: Rotatable Bracket Mounting

Section 6: Rotational Bracket Clearances

Lift xture up and insert provided (2) 1/4”

hex drive bolts through brackets, then

install provided locknuts.

Determine rotation of xture and lock

orientation in place (both sides) with

provided (2) 1/8” hex drive screws.

NOTE: Optional safety chains can be used

in 3/8” holes in sides of bracket and in the

mounting slots at the end of xture.

NOTE: Luminaire not to be directly facing the mounting surface nor within 45° of each

direction.

NOTE: The rotatable bracket requires a 5°C maximum ambient temperature derating.

10.9 in.

10.8 in.

15.5 in.

21.7 in.

Installation GuideAlbeo®ABR2 LED Luminaire

These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation,

operation or maintenance. Should further information be desired or should particular problems arise which are not covered sufciently for the purchaser’s purposes, the

matter should be referred to GE current.

Ces instructions ne prétendent pas couvrir tous les détails ou variantes de l’équipement ni couvrir toutes les conditions possibles à satisfaire en rapport avec l’installation,

l’opération ou l’entretien. Si des informations supplémentaires sont souhaitées sur des aspects qui ne sont pas sufsamment couverts pour satisfaire les besoins du client, ou si

des problèmes particuliers se présentent, veuillez addresser ces questions à GE current.

Estas instrucciones no pretenden cubrir todos los detalles o variaciones en el equipo ni para prever cualquier contingencia que debe cumplir en relación con la instalación,

la operación o el mantenimiento. De ser deseada más información o se surgieran problemas particulares que no están cubiertos sucientemente para los propósitos del

comprador, favor de remitirse a GE current.

www.gecurrent.com

General Electric Company and are used under license. Information provided is subject to change without notice.

All values are design or typical values when measured under laboratory conditions.

ALB019 (Rev. 05/05/2020)

Questions:

Web: products.gecurrent.com

Phone: 1-866-855-8629

Section 7: Troubleshooting

Section 8: Maintenance

Symptom Solution

Luminaire will not •Check that the color of the supply side wires match the color of the wires they are connected to.

turn on. •Check that all wire connectors are properly connected.

•Verify that your input voltage is within specs.

•If you are using any additional controls (i.e. dimming wires, motion sensors), please also verify that those are

working properly and that the unit is setup to interface with the controllers.

•

Product should not be disassembled during installation process and/or while installed.

•

Lens should be cleaned periodically for maximum lumen output.

•

Inspect and clear any build-up on cooling ns periodically for maximum performance.

Inhaltsverzeichnis

Andere GE Beleuchtungsausrüstung Handbücher

GE Tetra PowerMAX GEPM71-W1 Bedienungsanleitung

GE Evolve ERL1 Bedienungsanleitung

GE 79556 Bedienungsanleitung

GE LT-FCB-WF-3528-4W-36L-6M-Ex-W-120V Bedienungsanleitung

GE Tetra PowerMAX Bedienungsanleitung

GE Tetra miniMAX MS GEMS71-1 Bedienungsanleitung

GE Arize Factor HORT171 Bedienungsanleitung

GE 22332LO Bedienungsanleitung

GE LED 1000 5.5MM LIGHTS Bedienungsanleitung

GE LED Security Ligh Bedienungsanleitung

GE CMH Bedienungsanleitung

GE 23653a Bedienungsanleitung

GE LED-C9a-100 Bedienungsanleitung

GE LED 100 C5 LIGHTS Bedienungsanleitung

GE Cync Bedienungsanleitung

GE LED7-C7-50 Bedienungsanleitung

GE 78937 Bedienungsanleitung

GE Cync CFIXCNLR4S1 Bedienungsanleitung

GE 23071LO Bedienungsanleitung

GE 78966a Bedienungsanleitung

GE Decashield 1000 DSA Bedienungsanleitung

GE 3LED-C5-50 Bedienungsanleitung

GE LED2WT-7MM-50(0.032) Bedienungsanleitung

GE Tetra miniMAX Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung