GE ProSys DEH40206 Bedienungsanleitung

DEH40206 Installation Instructions

DESCRIPTION

The ProSys Lighting Control System is a small network of

relay panels and occupant control switches linked by a 4-wire

dataline. Together, these devices form a reconfigurable

switching platform — one that uses “softwiring” instead of

hardwiring to link occupant switches to relays.

There are four basic configurations of SWS (or dataline

switches): the single-gang, 1-, 2- and 4-button RS1PS-x,

RS2PS-x and RS4PS-x, respectively, and the two-gang,

8-button RS8PS-x.

Each switch includes a bi-color LED status light for each control

button and a locator light. In addition, the 2-, 4- and 8-button

units have directories which accept standard 3⁄8" wide (9mm)

labels. The x suffix in the catalog number refers to button and

switchplate color: 2 = ivory, 4 = almond, 7 = white and 9 = grey.

ProSys softwired switches are available with a key-

enabled override function. The switch will be disabled

except when a key is used to activate a 5 minute

override period. Dip switch 4 must be in the off position

to enable this feature as shown on page 8. Order this

feature by adding a -K to the part number for the 1- 2-,

4-, and 8-button switch. For example: RS2PSxK.

Any button on a Softwire Switch may be softwired to:

• Any relay or group of relays within a single relay panel

• A channel within a single relay panel

• The same channel among multiple panels (requires an

RCLK8PS Softwired Clock, which also operates as a

handheld programmer)

Before starting, read the following installation

instructions. If you have questions, call GE Total

Lighting Control Service at:

1-877-584-2685 (LTG-CNTL) in the USA and Canada.

RS1SWS-x RS2SWS-x

RS8PS-xRS4PS-x

ProSys Lighting Control System

Catalog Number RSxPS-x

GE Total Lighting Control

ProSys™Softwired Switches, 1-, 2-, 4- and 8-button

These instructions do not cover all details or variations in equipment nor do they provide for every possible contingency that may be met in connection with

installation, operation or maintenance. Should further information be desired or should particular problems arise that are not covered for the purchaser's purposes,

the matter should be referred to the GE Company.

DEH40206 Installation Instructions

The dataline connects relay panels, softwired switches and

optional control modules. Within the 4-wire dataline are two

twisted pairs: the red and black wires, carrying data; and the

blue and white wires, providing power to the dataline switches.

For simplicity, we refer to a 4-wire dataline running between

a relay panel and the dataline switches as a “Local Dataline”.

The relay panel provides the low-voltage power to all of the

dataline switches on its local dataline.

Note: To ensure good communications between panels,

the installer must comply with the dataline specification.

GE will not warrant a system using a dataline that does

not meet our specification. To avoid questions, use

GE RLONWIRE-4P (plenum rated). Do not run the

dataline in conduit or wiring trays with power wires.

Do not connect the local datalines from two different

panels.

GE RLONWIRE-4P Dataline Wire Specifications

•#18 AWG (7 strands x 26 AWG)

•2 independent twisted pairs –black/red, blue/white

•Unshielded copper conductors

•2 inch twist lay on pairs, 6 inch twist lay on cable

•Plenum-rated copolymer jacket, 0.230" O.D.

•FEP 0.010" insulation, 0.060" O.D.

•30 pF/foot maximum capacitance

•-20°C to 150°C operating temperature range

•17 lbs. per 500 foot reel

•UL rated

If you have purchased the ProSys Lighting Control System (the

stand-alone system), the devices (panels, switches and clock)

will be in self-install mode. This means that as soon as they

are connected to the network, they are operational and can

communicate with each other.

If you have purchased the ProSys LM Lighting Control System

along with the ProSys LM software, the devices will be in

software-install mode. This means that you must use your

network management tool to:

assign network addresses to the devices and

bind network variables and message tags.

Addresses and binding are necessary for the devices to

function on the network. ProSys LM users please refer to the

ProSys LM Software User Guide for instructions on installng

devices.

This instruction sheet will show you how to:

1. Install and Test a Local Dataline

2. Install and Test Dataline Switches

3. Softwire a Dataline Switch to Control a Group of Relays or

a Channel within a Single Panel

4. Document the Softwiring

LOCAL DATALINE INSTALLATION

DEH40206 Installation Instructions

The 1-, 2- and 4-button dataline switches mount in standard

single-gang switch boxes. The 8-button unit mounts in a

standard 2-gang box. The dataline is typically connected in a

“daisy-chain”from switch to switch, eliminating expensive

home runs. To assure proper operation, you must have a

good dataline which:

1. Provides 24 VAC power to each switch

2. Has a low resistance connection of the red and black wires

between all switches and the relay panel

3. Has no short of the red and/or black to ground

24 VAC Power

The power supply in the relay panel must be on. To test

for 24 VAC power at each switch, press the softwire tab after

you have connected the dataline but before mounting the

switch in the electrical box. The red LEDs for each button

should flash.

DATALINE SWITCH INSTALLATION AND TESTING

Low-Resistance Red/Black Data Path

After wiring the last switch on the local dataline, disconnect

the red and black wires from the Local Dataline terminals in

the relay panel and wire nut them together. Then measure the

resistance between the red and black terminals on the last

switch. It should be less than 3 ohms. If it is higher, work

backwards toward the relay panel, checking the resistance at

each switch to find the bad connection. When finished,

reconnect the Local Dataline at the panel.

Shorted Dataline

After the dataline resistance test checks out, you can easily

test for a shorted dataline by measuring the resistance from

red to white, then black to white anywhere on the dataline.

You should see an open circuit. If there is a short, start at the

last switch and work backwards as above to locate it.

Self Installation and Unconfiguring

When the switch is first connected to a panel it is automati-

cally issued a network address—it is configured. If you are

moving a switch to another network you must first

unconfigure it to delete its network address. (A configured

switch could have the same address as a node on another

network.)

To unconfigure a switch, first make sure that the fourth DIP

switch is in the ON position. Leave the power line on but

disconnect the dataline. (Disconnecting the dataline prevents

the panel from configuring the switch again.) Hold down the

softwire tab for at least 10 seconds. At 10 seconds the locator

LED will turn off indicating that the switch is unconfigured.

As shown in Figure 1 below, dataline switches are numbered

sequentially beginning with 01-01 (Panel 01-Switch 01). A

single switch unit may have 1, 2, 4 or 8 buttons. Switch units

should be identified on the reflected ceiling plan showing the

number of buttons in each location. Check to confirm that the

correct switch unit has been installed at each location.

A separate ProSys SWITCH DOCUMENTATION form

should be used for each relay panel to record the number of

the switch and its number of buttons. Allow one line for each

button as shown on the form in Figure 2 below. For example,

switch 01-01 has four buttons. The form should list all buttons

on each switch, even if you are not using all of them.

NUMBER AND DOCUMENT DATALINE SWITCHES

Any switch button may be softwired to control a single relay

or a group of relays within any single panel (see next page for

softwiring a dataline switch). For example, assume that you

want the top two buttons of a 4-button switch to control open

office areas associated with relays in Panel 01, while the

third button controls common areas (rest rooms and hallways)

in Panel 02. The form below shows how to record this intent

and also shows the labeling for each switch button. Finally,

write the switch number on the label in the lower right corner

of the switch base (see Figure 4 on page 5).

Figure 1

DATALINE SWITCH DOCUMENTATION

SWITCH # BUTTON RELAYS CONTROLLED DESCRIPTION

MAX

-01 1 -01, -02 OFFICE - NW

" 2 -03, -04 OFFICE - NE

" 3 SPARE

" 4 "

-02 1 -15, -16 HALLWAYS NORTH

" 2 -17, -18 HALLWAYS SOUTH

Figure 2

PANEL #

01-01 01-02

02-01 02-02

01-03 01-04

02 xx

PANELS

NUMBERED

SEQUENTIALLY

BEGINNING

AT 01

DATALINE

18/4 AWG

1500 FT. MAX.

GE RLONWIRE-4P

DATALINE SWITCHES FOR EACH PANEL

NUMBERED SEQUENTIALLY (PANEL #-SWITCH #)

MAXIMUM TOTAL NUMBER OF RELAY PANELS AND DATALINE SWITCHES IS 64

SWITCH

BUTTONS

(#1 AT TOP)

RELAY

PANEL

RELAY

PANEL

RELAY

PANEL

SOFTWIRING A DATALINE SWITCH TO A GROUP OF RELAYS

Patterns or Scenes

Any dataline switch may be configured as either an

ON/OFF Group Switch or a Pattern Switch. The

Patterns mode allows the group of relays to be forced

to a combination of ON/OFF states to provide a

lighting scene or pattern. For consistency of

operation, do not mix Group and Pattern buttons on

the same switch unit. For more information on

Patterns, refer to SPECIAL FUNCTIONS on page 7.

Softwiring a Dataline Switch in Patterns mode is similar to

that described in Figure 3, with one additional step:

1. Press the SOFTWIRE tab.

2. Press the switch button.

3. Press the PATTERNS button in the relay panel (pictured

above).

4. Select the relays to be controlled. This time, pressing the

relay control button will toggle the relay’s LED from red to

green to off before toggling back to red again.

Select relays as follows:

LED Red: Relay in the group and ON (turns ON when the

button is pressed)

LED Green: Relay in the group but OFF (forced OFF when

the button is pressed)

LED OFF: Relay not in the controlled group

5. Press the SOFTWIRE tab again.

Dataline switches are typically wired to a single relay or

group of relays within a panel (See Figure 3, right). Wiring to

a channel is a shortcut —it provides a simple way of

manually overriding all of the relays which are grouped to an

automation channel (A-H) within a panel.

With the wallplate removed and the switch’s master

button flipped open…

1 Press the SOFTWIRE tab. The LED next to the

tab will turn on, then the individual button LEDs

will start flashing.

2 Press the switch button you want to softwire

(Master Button on an RS1PS-x). The LED for

that button will continue to flash; LEDs for the

other buttons will stop flashing. LEDs for the relays

currently controlled by that switch button will also

begin to flash.

3 Select the relays to be controlled. In the relay

panel, press the associated relay control button to

add/delete that relay to/from the group.*

4 Press the SOFTWIRE tab again. All LEDs will

stop flashing. The selected switch button will now

control the selected group of relays.

Test. Press the selected switch button again to

toggle the relay group ON/OFF/ON. Now press

each relay control button to turn the relay OFF. The

switch button LED will go from red (all relays ON)

to green (mixed group) to off when the last relay in

the group is turned OFF.

* To softwire a dataline switch to a channel, press the channel

button instead of the relay control button.

Figure 3 –Softwiring a Dataline Switch

FLASHING

LED

TURNS

SWITCH BUTTONS

ALL LEDS

BEGIN FLASHING

SOFTWIRE TAB

RELAY

CONTROL

BUTTON

SELECTED

LED

CONTINUES

FLASH

OTHER

LEDS

STOP

FLASHING

LED

TURNS

OFF

DEH40206 Installation Instructions

SWITCH BUTTON LABELING

The individual switch buttons provide space for 3⁄8" wide x 11⁄16"

long (9mm x 30mm) label directories. The directory labels can

be attached simply by removing the clear lenses, positioning

the labels and replacing the lenses as shown at right.

If desired, the buttons may be completely removed from the

base plate and labeled separately. You may find this method

easier to achieve better alignment of the labels.

To remove a button from a 1-, 2- or 4-button switch, open it

out from the base until it is at a 90°angle, then gently rotate

it up or down until it snaps free of the hinge bracket. To

replace the button, press the hinge pin into the hinge bracket

until it snaps in place, then close the button into position.

Removing buttons from an 8-button switch is slightly

different. With your fingernail or small screwdriver, pry the

hinge end of the button free from the hinge bracket. Lift the

button out, twisting it slightly, if necessary, to free the small

hook holding the center edge of the button in place. To replace

the button, position the small center hook in place and press

the hinge pin into the hinge bracket until it snaps in place.

Remove/Replace Screwless Wallplate

To remove the screwless cover plate, press in the black tab at

the bottom edge of the plate and lift the plate up and off. To

replace the cover plate, place the hang bar at the top of the

plate onto the hang hook at the top of the switch base and

snap the bottom in place until it clicks as shown in Figure 4.

Record Switch Reference Numbers

The switch’s reference number (Panel #-Switch #) should be

written on the small label placed in the lower right hand

corner of the switch base, so that it is visible when the cover

is removed.

The relays or channel associated with each button of the switch

are recorded on the DATALINE SWITCH DOCUMENTA-

TION form supplied with the relay panel. The completed form

should be stored in the cover of the relay panel that is

connected to this local dataline.

Panel#

Switch#

Figure 4 –Dataline Switch Numbering

DEH40206 Installation Instructions

01-01

01-02

01-03

SPECIAL FUNCTIONS

ProSys is designed to provide flexibility without compromising

simplicity in installation and operation. The Special Functions

described here may be used to enhance the operation of your

system, but they are not required in most installations.

Patterns

A Pattern is a combination of ONs and OFFs for a group of

relays which creates a scene. Any button on a dataline switch

may be softwired to create such a scene.

Simplifying Rule: If any button of a switch unit is softwired as

a Pattern, ALL of the buttons on that switch unit should be

softwired as Patterns.

When the relay pattern for a switch button is “true”, the LED

for that button will be ON RED. If “not true”the LED will be OFF.

Example –An office with four 3-lamp fluorescent

fixtures and six wall wash units (see Figure 5):

We want the local switch to provide 1⁄3, 2⁄3and Full On for the

fluorescents, and separate control of the wall-wash units. The

form below in Figure 7 shows how the four buttons on a

quad switch would be softwired to create this switching

function. All of the buttons are wired as Patterns.

Reviewing the LED operation shows why this is important

(see Figure 6). When the occupant toggles the top button ON,

relay 01-01 will turn ON and relay 01-02 will turn OFF to give

1⁄3lighting. The LED for 1⁄3will turn on red. Pressing the second

button causes the relay states to reverse, giving 2⁄3lighting.

The 1⁄3button LED turns off (since its pattern is no longer

“true”) and the 2⁄3LED turns on. Similarly, pressing the Full On

button turns ON both relays giving full lighting, the 2⁄3LED

turns off, the Full LED turns on. Everything is as it should be.

If, on the other hand, we had softwired the third button as a

standard ON/OFF group, we would have seen an odd response.

Whenever, buttons 1 or 2 were turned on, the third button LED

would be on green, showing a mixed state for its relays.

1⁄3Lighting plus wall wash

2⁄3Lighting plus wall wash

Full lighting plus wall wash

Figure 5

Figure 6

DATALINE SWITCH DOCUMENTATION

SWITCH # BUTTON RELAYS CONTROLLED DESCRIPTION

MAX

-01 1 -01, -02 1/3

" 2 -01, -02 2/3

" 3 -01, -02 FULL

" 4 -03 WALL WASH

Figure 7

PANEL #

DEH40206 Installation Instructions

ALL ON/ALL OFF

To convert to All ON/All OFF

operation, DIP switch 1 is moved to

the OFF position (1 OFF, 2 ON). This

operation is typical in a prison

application: individual control of

each cell with a Master ON/OFF to

override a bank of switches quickly.

Master Button Alternate Scenarios

OFF/RESTORE —The Default Setting

The Master Button on the 2-, 4- and 8-button switch is pre-

configured to provide an OFF/Restore scenario. If several

individual switch buttons are ON, hitting the Master turns all

of those buttons OFF. Hitting the Master again would turn

those same switches back ON.

Example (Figure 8): Assume that in the previous office

example, an occupant prefers a lighting arrangement with the

fluorescents at 1⁄3and the wallwash units on. Once the

buttons on the switch are set to this combination, all the

occupant needs to do from then on is to press the Master

Button to turn off or restore this lighting combination.

Another example: Assume an 8-button switch is used to

control eight zones in an open office space. At the end of the

day, all but two zones have been turned off. Upon leaving, a

conscientious employee uses the Master Button to turn off

the remaining lighting, only to hear an exclamation from the

back corner…someone is still there. Pressing the Master

Button again would restore the lighting in the two zones

which had been on, without having to turn on the entire floor.

You can change the operating

scenario of the Master Button

using the first two DIP switches

located on the back of the

switch.The DIP switches are

normally covered by a label to

prevent accidental changes. As

shown above, the factory default setting is all DIP switches in

the ON position: each DIP switch is depressed towards the

numbers along the top, indicated here by the black dots.

To access the

Master Button DIP

switches, remove

the gray portion in

the upper right

corner of the label

on the back of the

dataline switch.

SPECIAL FUNCTIONS (CONTINUED)

OFF ONLY

To convert to Master OFF Only, DIP

switch 1 is ON, switch 2 is OFF.

This is an energy-efficient setting,

but not very occupant friendly. For

example, in our office application,

this would make the occupant reset

the desired lighting combination every morning. (Don’t use

this configuration with Pattern switches).

DISABLED

Both DIP switches OFF. This configuration may be preferred

when there is concern about

someone “accidentally”turning on

all of the lights on the floor.

DISABLED & OVERRIDE

Moving the fourth DIP switch to the

OFF position as shown, disables the switch but allows for a

five-minute override. When the DIP

switch is in the OFF position the

switch can be enabled for five

minutes by pressing the service

pin.

1⁄3Lighting plus wall wash

Master OFF

Master Restore

Figure 8

DEH40206 Installation Instructions

Cleaning Switch

The third DIP switch, when set in

the OFF position as shown, changes

the operation of the entire switch

unit to provide a Cleaning Scenario.

The intent of the cleaning scenario is to allow the cleaners to

turn on or off a large area without negatively affecting

occupants who may be staying late. When in the cleaning

mode, any button on the switch unit will turn ON the relays

softwired to that switch button, similar to a standard switch.

However, when the button is toggled off, any relays which are

ON because of an occupant override will remain ON.

SPECIAL FUNCTIONS (CONTINUED)

Combining the Cleaning Scenario with Pattern operation can

provide an elegant solution to control of cleaning lights (see

Figures 9 and 10). Let’s assume that switch 01-01 has been

configured as a cleaning switch with button 1 controlling a

Pattern in which the north half of the floor is ON and south

half is OFF. The second button does just the reverse. With this

combination, whenever the cleaners turn on one half of the

floor, the other half turns off automatically, saving half the

lighting. Furthermore, since switch 01-01 has been configured

as a cleaning switch, the cleaning crew cannot accidentally

put an occupant in the dark. For instance, if an occupant has

used a switch to turn ON relay 01-01, the cleaning switch

cannot turn that relay OFF as shown in the sequence below.

1. After hours, all lights are off.

2. Late-working occupant enters,

turns on lights in Zone 1.

3. Cleaning crew presses Button

1 on Cleaning Switch to turn

on north cleaning area.

4. Cleaning crew presses Button

2 on Cleaning Switch to turn

on south cleaning area –lights

in north cleaning area turn off,

except for Zone 1.

1234

Figure 9

Figure 10

GE Total Lighting Control

41 Woodford Avenue, Plainville, CT 06062

GE Total Lighting Control

DEH40206 BL 0700 R02

Inhaltsverzeichnis

Andere GE Beleuchtungsausrüstung Handbücher

GE CMH Bedienungsanleitung

GE Current Evolve LED Wallpack EWL Bedienungsanleitung

GE Current Tetra Slim EdgeStrip Series Bedienungsanleitung

GE Tetra Contour GEXNLG15 Bedienungsanleitung

GE StayBright RTL-FPC-2835-2.5cm-19.6FT-120V-G Bedienungsanleitung

GE DSN-XM-MK0288-5FT-120V-M Bedienungsanleitung

GE RTL-FPC-2835-2.5cm-19.6FT-120V-Ex-R Bedienungsanleitung

GE 73007 Bedienungsanleitung

GE STANDING REINDEER Bedienungsanleitung

GE 62191 Bedienungsanleitung

GE Tetra miniMAX MS GEMS71-1 Bedienungsanleitung

GE Arize Element L1000 Gen2 Bedienungsanleitung

GE Tetra Contour LS Bedienungsanleitung

GE Tetra GETP35-2 Bedienungsanleitung

GE LED 500 LIGHTS Bedienungsanleitung

GE LED 50 C9 LIGHTS Bedienungsanleitung

GE Tetra PowerMAX GEPM71-W1 Bedienungsanleitung

GE 73014LO Bedienungsanleitung

GE ReliaGear 400 A Bedienungsanleitung

GE Arize Element Top Light Bedienungsanleitung

GE Tetra Atom Bedienungsanleitung

GE 17421 Bedienungsanleitung

GE NHL 23119LO Bedienungsanleitung

GE NHL 82004LO Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung