GE 45235 Bedienungsanleitung

www.jascoproducts.com

1-800-654-8483

45235

Home Monitoring

B/W Wireless

Camera System

with Monitor

User Manual

Thank you for purchasing the GE 45235 B/W

Wireless Camera System with Monitor. Please

review these instructions carefully before

attempting to operate the unit.

PRODUCT FEATURES

“Wi-Fi” internet friendly wireless system—won’t

interfere with home wireless networks

View up to two cameras automatically

Audio Detection & Notiﬁcation feature—alerts

when sound is detected in a monitored area

Night Vision feature for low or no light viewing

up to 10 ft.

Unique “axis-swivel” camera mount allows for

desktop or wall installation

Adjustable antenna for both camera and

monitor

Wirelessly transmits audio and video up to 200 ft

(unobstructed line of sight)

Camera for Indoor/Outdoor use

PACKAGE CONTENTS

Please check and identify all the parts before

proceeding with the installation.

•

45235B/W Wireless Camera

45235 5.5” B/W CRT monitor

Wall mounting hardware

2 AC adapters

BEFORE YOU INSTALL

When choosing the best location for the placement

of the camera and monitor, it is best to avoid any

sources of possible RF interference such as

microwave ovens and cordless phones. Proximity

to these and other sources of RF interference can

inhibit the proper functioning of the receiver.

The 900MHz video signals pass easily through

your home’s interior walls, but the signal may be

reﬂected by power wires or plumbing inside those

walls. Usually a slight adjustment to the position

of the Monitor/Receiver and/or Camera antenna

will improve reception. Take care not to force the

antennas past their lock positions.

CHOOSING A CAMERA MOUNTING LOCATION

The Wireless B/W Camera included in the 45235

system can be positioned on a desktop, or

mounted to a wall. It is suitable for indoor or

outdoor use. When choosing a mounting location,

please be advised:

Do not use in wet locations. If using outside,

position camera in a sheltered location.

Do not position the camera so that it points

directly into the sun or any bright light, as this

may cause damage to the camera.

Avoid viewing areas where half the area is in

bright sunlight and the other half is dark, such

as in the shadow of a building. All types of

cameras have difﬁculty “seeing” into areas of

such divergent light levels.

In low light conditions, the camera will

automatically activate the Infrared (IR) LED’s and

switch the camera to Night Vision mode. Night

Vision viewing distance is up to 10 feet.

The AC adapter used to power the camera

cannot be positioned farther than 8 ft. from

an AC socket. Do not use the supplied adapter

outside or run the cable through walls. If you

need to extend the adapter cable, 15 ft.

extensions are available by contacting

Customer Service at 800-654-8483.

The Camera has an unobstructed wireless

transmission range up to 200 ft. from the

receiver. Transmission distance indoors is

reduced due to interior walls, wiring, household

ﬁxtures and metal plumbing.

•

CONNECTING TO THE MONITOR

Before beginning installation, we recommend that

you temporarily “connect” the 45235 B/W Wireless

Camera to the 5.5” Monitor to help familiarize

yourself with the camera system and select the

best location for installing the camera. The camera

connects wirelessly and automatically to the monitor

when both are powered on and within 200 ft. of

each other (unobstructed view). This system will

accommodate up to 2 cameras.

1. Plug the AC adapter into the power jack on the

back of the monitor, then into an AC outlet.

2. Turn on the monitor by pressing the power

button on the front of the unit. Adjust the sound

level at the front of the monitor to midpoint with

the volume control knob.

3. Select the appropriate “channel” (1 or 2) on the

monitor that corresponds to the channel switch

Shown with optional

rechargeable battery

(Sold separately)

setting (1 or 2) located on

the unside of the camera

housing. (See Channel

Selection.)

4. Brightness/Contrast and

Vertical Hold can be adjusted

with controls at the back of

the monitor.

CHANNEL SELECTION

Manual Mode

To select one of the two channels manually,

press the MANUAL button on the front panel

of the Monitor. The green LED will light for the

corresponding channel. The Monitor will switch to

a different channel (1 or 2) each time the MANUAL

button is pressed. When you have selected the

channel with the active camera, that video will

appear on the monitor screen. Each camera must

be assigned to a speciﬁc channel; both cameras

cannot be on the same channel or the signals will

cancel out.

Video Out

CHANNEL

13.5V 1.2A

BEEP

V-HOLD BRIGHT CONT

TRIGGER

1 2 1/2

Audio Out

–+ –+

Monitor

controls

Channel

Selection switch

Channel

Selection

switch

1 2

Multi-Camera Operation

This wireless surveillance system is designed to

work with up to 2 cameras. Additional cameras

are sold separately. IMPORTANT: When using

more than one camera, each camera must be

assigned to a speciﬁc channel using the channel

selection switch located on the underside of the

camera housing.

Select either 1 or 2 for each camera. Each camera

must be assigned to a speciﬁc channel; both

cameras cannot be on the same channel or the

signals will cancel out. If using only one camera

you can select either Ch 1 or Ch 2, whichever

provides the best picture. The slide switch located

on the rear of the Receiver must be set to reﬂect

the channels in use.

Auto Mode (2 Camera Operation)

To have the Monitor automatically switch between

two active channels, ﬁrst check the receiver is set

CAMERA 1

Channel Setting

CAMERA 2

Channel Setting

1 2 1 2

MONITOR

Video Out

CHANNEL

13.5V 1.2A

BEEP

V-HOLD BRIGHT CONT

TRIGGER

1 2 1/2

Audio Out

–+ –+

Channel

Selection

switch

to 1/2 position. Next, press the AUTO button on the

front panel of the Monitor. The green LED will light

and the Monitor will automatically select between

the two active cameras. The monitor will display

images from both cameras alternately.

Cycle Time Setting

(Time interval between camera selections)

The default cycle time for the receiver is preset to

4 seconds. To change the cycle time, press both of

the buttons (Auto/Manual) on front of the receiver

simultaneously. The Monitor will beep. Each beep

is one extra second of cycle time added. The cycle

time can be veriﬁed by the number of ﬂashes the

LED makes when you release the buttons—one

ﬂash equals one second. Cycle time can be set

between 2-30 seconds.

NIGHT VISION

The 45233 Wireless Color Camera features Night

Vision technology. Objects and images can be seen

in little or no light up to 10 ft. The camera uses a

special image sensor that automatically detects

available light levels. It turns on/off the Infra-Red

(IR) LEDS on the front of the camera. These LEDs

provide artiﬁcial light that allows the camera to

‘see’ in the dark. Night Vision will appear as a Black

and White image. When the image sensor detects

Sensor

Infra-Red

(IR) LEDs

enough light, color will

return to the images.

AUDIO DETECTION AND

NOTIFICATION FEATURE

This feature allows the system

to emit an audio alert whenever

sound is detected within a

monitored area. When the

camera detects a sound, the

receiver will sound an alert and

‘Alarm’ light on the front of the Monitor will ﬂash. The

sensitivity for the level of audio detection (when the

Monitor will sound an alert) can be adjusted with the

sensitivity control located at the back of the Monitor.

The alert sound can be turned OFF by adjusting the

sensitivity control to ‘-’ (Minimum).

INSTALLATION

Once your preferred camera mounting location

has been chosen, power OFF the Monitor and

disconnect the AC adapter from the wireless

camera before proceeding.

Video Out

CHANNEL

13.5V 1.2A

BEEP

V-HOLD BRIGHT CONT

TRIGGER

1 2 1/2

Audio Out

–+ –+

Sensitivity

Control

(Trigger)

Desktop Mount:

1. Place camera in desired

location on a ﬂat surface.

2. Set Channel switch on

camera to 1 or 2.

3. Reconnect AC adapter to

the camera and power on the

monitor.

4. Adjust antenna and camera

angle as needed for the clearest

picture. Positioning the antenna

upwards to improve transmission distance, and

downwards to reduce transmission. Take care not

to force the antenna past its lock positions.

Wall Mount:

1. To simplify the wall mount process, you will ﬁnd

a custom wall mounting plate included with the

mounting hardware.

2. Select the ideal location. Using the supplied mount

as a template, drill two 3/16” holes in the desired

mounting location, and install the two wall anchors

(included) into the holes, or screw directly into a wall

stud. Secure the mounting plate to the wall, Do not

run the adapter cable in walls; when securing the

cable, do not cut or puncture.

MIN

SENSITIVITY

MAX

Antenna pivots to

increase/decrease

signal strength

Inhaltsverzeichnis

Andere GE Sicherheitssystem Handbücher

GE CareGard Bedienungsanleitung

GE Security Pro 7000 Bedienungsanleitung

GE Simon XT V2 Bedienungsanleitung

GE 1200 Series Bedienungsanleitung

GE Concord Ultra Bedienungsanleitung

GE SmartCom CC-SCRS01 Bedienungsanleitung

GE 45129 Bedienungsanleitung

GE 60-960-95 Bedienungsanleitung

GE 45236 Bedienungsanleitung

GE SIMON XT Bedienungsanleitung

GE TX-7201-05-1 Bedienungsanleitung

GE 600-1064-95R b Bedienungsanleitung

GE NX-10 Bedienungsanleitung

GE Concord 4 Gebrauchsanweisung

GE AL-1291 Point ID Bedienungsanleitung

GE AS610RF Bedienungsanleitung

GE SIMON XT Bedienungsanleitung

GE NX-10 Benutzerhandbuch

GE BA300 Schulungshandbuch

GE NetworX V3 Bedienungsanleitung

GE Security Pro 1000 Bedienungsanleitung

GE SmartHome Series Bedienungsanleitung

GE 610 Bedienungsanleitung

GE Interlogix 60-875 Simon Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung