GE Concord 4 Bedienungsanleitung
GE Concord 4 Quick Setup Guide
For more detailed information, please see the GE Installation Manual.
1. Planning your system
a. Wired Zones: A hardwired zone can consist of 1 or more sensors in a loop.
Each zone loop must consist of similar sensors, that can be programmed the
same.
i. Normally Open Sensors ormally open sensors have an “Open”
circuit until the sensor is tripped, it will then close the circuit. This
change is detected by the panel, and causes the alarm. These sensors
get wired in Parallel. (See Wiring Diagrams)
ii. Normally Closed Sensors ormally closed sensors have a “Closed”
circuit until the sensor is tripped, it will then open the circuit. This
change is detected by the panel, and causes the alarm. These sensors
get wired in Series. (See Wiring Diagrams)
iii. Powered Sensors Powered Sensors, such as Motion detectors, Glass
Break Detectors will require a 4 conductor wire. Two wires are for
power connections, and two wires
are for the zone connections.
b. Wireless Zones Unlike wired zones, for
each wireless sensor you will use 1
wireless zone. Each sensor is programmed
to a zone with all information for that
individual sensor.
2. Wiring the System
a. Keypads All Keypads get wired to Pins 3,
4, 5, and 6. the system will automatically
detect the number of keypads connected
to the system. Match the colors used on
each pin, to the corresponding connections
on the keypad. (See Diagram to Right)
b. Sensors
i. Normally Open Sensors Check
the product documentation – If the
Loop Type is “ O” or “ ormally
Open” then the sensors should be
wired in Parallel with the zone.
(See Diagram On Last Page)
ii. Normally Closed Sensors Check
the Product Documentation – If the
Loop Type is “ C” or “ ormally
Closed” then the sensors are wired in Series with the zone (See
Diagram to On Last Page)
3. Programming The System
a. Entering Programming Mode
1. Make sure the system is disarmed in all partitions.
2. Press 8 + 4321 + 0 + 0. The display shows “SYSTEM PROGRAMMING”.
b. Programming Hardwired Zones
i. Zone Groups are pre-programmed for the 8 hardwired zones.
1. Entry Exit Delay – For Doors that require a delay for entry or
exit
2. Instant Interior Follower – For motion detectors that will
arm instantly.
3. Instant Perimeter – For all doors/window sensors, glass
break detectors that do not require a delay.
ii. **Change the “Pre-Programmed” Zone Settings
1. Once you are in the programming mode, press B until the
display shows “Sensors”, and press # to select
2. ow Press B until the display shows “Edit”, and press # to
select.
3. Press A or B to scroll to the zone number you desire to change
press # to select
4. Enter the desired partition number, and then press #. (Most Applications the
Partition is always 1) The display shows the new partition assignment.
5. Press A or B and the display shows SENSOR GROUP nn (current group
assignment)
6. Enter the desired group number, (See appendix B in Installation Manual) then
press #. The display shows the new group assignment.
c. Programming Wireless Zones
i. With the display showing SENSORS, press # and the display shows “Learn Sensors”
ii. Press # and the display shows Sensor PTN 1
iii. Press # to select partition 1 or press 2, 3, 4, 5, or 6 + # to select the desired partition
(Typically is always Partition 1). The display should show “Sensor Group 0”
iv. Enter the desired sensor group number and press # to select (see Table B1 in “Appendix
B” for a description of all sensor group characteristics). The display shows TRIP
SENSOR nn, where nn is the displayed (next available) sensor number.
v. To change the displayed sensor number, enter the desired sensor number + #. The desired
sensor number is displayed.
vi. With the desired sensor number displayed, use the guidelines in Table 6 to force the
sensor or zone you are adding (learning) into the panel memory to send a signal to the
panel.
vii. To add another sensor to the same sensor group and partition, go back to step 5.
viii. To add sensors to another sensor group or partition, press * twice and go back to step 1
(LEARN SENSORS).
d. Changing Wireless Zone Settings:
i. If you need to change a zone setting – Enter Programming Mode, Press B to Scroll the
menu. Select “Sensors” # “Edit” # Select the Zone you wish to Edit, and make the desired
changes pressing # to save the desired changes.
e. Exiting Programming Mode
i. After all installer/dealer programming is completed, use the following procedure to exit
programming mode.
To exit programming mode:
1. Press * until the display shows SYSTEM PROGRAMMING.
2. Press A or B until the display shows EXIT PROGRAMMING READY.
3. Press # and the touchpad displays the TIME AND DATE.
f. Using The System
i. Setup User Codes:
1. To Enter User-Programming Mode
a. Press 9 then the 4 digit Master Code (Default is 1234)
2. Scroll Menu using the B Button until you reach “User”
3. With the display showing USER CODES, press # and the display shows REGULAR
USER CODES.
4. Press # and the display shows USER nnn (first available user number).
5. Press A or B to select the desired user number, and then press #. The display
shows USER nnn - nnnn.
6. With the desired user number displayed, enter a 4-digit user code. The display
flashes the entered code. Press # and the display shows USER nnn - nnnn (new
code).
Zone Wiring Diagrams
Andere Handbücher für Concord 4
3
Inhaltsverzeichnis
Andere GE Sicherheitssystem Handbücher
GE
GE Deluxe 45117 Bedienungsanleitung
GE
GE 45235 Bedienungsanleitung
GE
GE 610 Bedienungsanleitung
GE
GE 45133 Bedienungsanleitung
GE
GE SIMON XT Gebrauchsanweisung
GE
GE Concord Ultra Bedienungsanleitung
GE
GE SIMON XT Bedienungsanleitung
GE
GE SIMON XT Bedienungsanleitung
GE
GE Concord 4 Gebrauchsanweisung
GE
GE Concord Bedienungsanleitung
GE
GE GEC-4VDPC Montageanleitung
GE
GE SmartHome Series Bedienungsanleitung
GE
GE 60-362 Bedienungsanleitung
GE
GE NX-10 Benutzerhandbuch
GE
GE Interlogix 60-875 Simon Bedienungsanleitung
GE
GE 45411 Bedienungsanleitung
GE
GE Interlogix 60-875 Simon Bedienungsanleitung
GE
GE Allegro 60-874-95R Bedienungsanleitung
GE
GE SIMON XT Bedienungsanleitung
GE
GE Telligence Patient-Staff Communications... Bedienungsanleitung
Beliebte Sicherheitssystem Handbücher anderer Marken
EDM
EDM Solution 6+6 Wireless-AE Bedienungsanleitung
Highway Safety Group
Highway Safety Group EA401 Bedienungsanleitung
Siren
Siren LED GSM Bedienungsanleitung
Detection Systems
Detection Systems 7090i Montageanleitung
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung
Siemens
Siemens FDM273 Bedienungsanleitung