GE 25982EE2 Bedienungsanleitung
Your telephone equipment is approved for connection to the Public Switched Telephone Network and
is in compliance with parts 15 and 68, FCC Rules and Regulations and the Technical Requirements for
Telephone Terminal Equipment published by ACTA.
On the bottom of this equipment is a label indicating, among other information, the US number and
Ringer Equivalence Number (REN) for the equipment. You must, upon request, provide this information
to your telephone company.
The REN is useful in determining the number of devices you may connect to your telephone line and
still have all of these devices ring when your telephone number is called. In most (but not all) areas, the
sum of the RENs of all devices connected to one line should not exceed 5. To be certain of the number
of devices you may connect to your line as determined by the REN, you should contact your local
telephone company.
A plug and jack used to connect this equipment to the premises wiring and telephone network must
comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant
telephone cord and modular plug is provided with this product. It is designed to be connected to a
compatible modular jack that is also compliant. See installation instructions for details.
• This equipment may not be used on coin service provided by the telephone company.
• Party lines are subject to state tariffs, and therefore, you may not be able to use your own telephone
equipment if you are on a party line. Check with your local telephone company.
• Notice must be given to the telephone company upon permanent disconnection of your telephone
from your line.
• If your home has specially wired alarm equipment connected to the telephone line, ensure the
installation of this product does not disable your alarm equipment. If you have questions about what
will disable alarm equipment, consult your telephone company or a qualied installer.
Should your equipment cause trouble on your line which may harm the telephone network, the
telephone company shall, where practicable, notify you that temporary discontinuance of service
may be required. Where prior notice is not practicable and the circumstances warrant such
action, the telephone company may temporarily discontinue service immediately. In case of such
temporary discontinuance, the telephone company must: (1) promptly notify you of such temporary
discontinuance; () afford you the opportunity to correct the situation; and (3) inform you of your right to
bring a complaint to the Commission pursuant to procedures set forth in Subpart E of Part 68, FCC Rules
and Regulations.
The telephone company may make changes in its communications facilities, equipment, operations
or procedures where such action is required in the operation of its business and not inconsistent with
FCC Rules and Regulations. If these changes are expected to affect the use or performance of your
telephone equipment, the telephone company must give you adequate notice, in writing, to allow you to
maintain uninterrupted service.
3
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference; and () This device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
P
rivacy of Communications may not be ensured when using this product.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is “receiving”
the interference).
• Reorient or relocate and increase the separation between the telecommunications equipment and
receiving antenna.
• Connect the telecommunications equipment into an outlet on a circuit different from that to which the
receiving antenna is connected.
If these measures do not eliminate the interference, please consult your dealer or an experienced radio/
television technician for additional suggestions. Also, the Federal Communications Commission has prepared
a helpful booklet, “How To Identify and Resolve Radio/TV Interference Problems.” This booklet is available from
the U.S. Government Printing Ofce, Washington, D.C. 040. Please specify stock number 004-000-00345-4
when ordering copies.
Notice: The changes or modications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
This telephone system meets FCC standards for Hearing Aid Compatibility.
Licensed under US Patent 6,47,009.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 0 centimeters between the
radiator and your body. This transmitter must not be co-located or operated in conjunction with any other
antenna or transmitter.”
For body worn operation, this phone has been tested and meets the FCC RF exposure guidelines when
used with the belt clip supplied with this product. Use of other accessories may not ensure compliance
with FCC RF exposure guidelines.
4
EquipmEnt ApprovAl informAtion .................2
intErfErEncE informAtion .............................3
HEAring Aid compAtibility (HAc) .................3
licEnsing .....................................................3
fcc rf rAdiAtion ExposurE stAtEmEnt ........3
tAblE of contEnts .......................................4
introduction ...............................................6
bEforE you bEgin ........................................6
Parts CheCklist (for 25982xx2 model) .6
telePhone JaCk requirements.........................6
instAllAtion .................................................7
digital seCurity system ...................................7
imPortant installation guidelines .................7
HAndsEt And cHArgE crAdlE lAyout ............8
bAsE lAyout .................................................8
instAlling tHE pHonE ....................................9
installing the handset Battery ......................9
installing the Phone .....................................10
ConneCting the aC (eleCtriCal) Power 10
ConneCting the telePhone line ..............10
attaChing the Pedestal BraCket ............11
ConneCting the Corded handset ..........11
AnswEring systEm sEt up ..........................11
VoiCe instruCtions .........................................11
AnswEring systEm opErAtion ....................12
reCording the outgoing announCement ..12
reViewing announCement.............................12
leaVing a message .........................................12
sCreening Calls from the Base ...................13
sCreening Calls from the handset ............13
message PlayBaCk from Base unit .............13
erasing messages ..........................................14
leaVing a memo ..............................................14
tElEpHonE sEt up ......................................15
language .........................................................15
handset name ................................................16
disPlay Contrast ...........................................16
rings to answer ............................................16
seCurity Code .................................................17
Base ringer leVel ..........................................17
handset ringer on/off ............................18
ringer tone ....................................................18
ViP ring tone ................................................18
setting day/time............................................19
loCal area Code ............................................19
tone/Pulse dialing .......................................20
transfer on/off.........................................20
registration (link Cordless handset) .......20
default setting ..............................................21
bAsic opErAtion .........................................21
answering a Call ..........................................21
Cordless handset ....................................21
Corded handset .......................................21
Base sPeakerPhone ...................................21
making a Call.................................................22
Cordless handset ....................................22
Corded handset .......................................22
sPeakerPhone .............................................22
manual Channel seleCtion ..........................22
Call timer .......................................................22
auto standBy ..................................................22
handset ringer on/off shortCut .........23
do not disturB .............................................23
flash ................................................................23
Call transfer .................................................24
transferring Call from Base to Cordless
handset ......................................................24
transferring Call from Cordless handset
to another Cordless handset/Base .....24
last numBer redial .......................................24
Base sPeakerPhone ...................................24
Corded handset .......................................25
Cordless handset ....................................25
hold .................................................................25
Paging the Cordless handset .....................25
mute .................................................................26
Volume .............................................................26
sPeakerPhone .............................................26
Corded handset .......................................26
Cordless handset ....................................26
5
answering system .....................................26
Vmwi indiCator on handset .................26
Base unit sPeakerPhone oPeration ............27
reCeiVing a Call with sPeakerPhone .....27
making a Call with sPeakerPhone ........27
switChing Between sPeakerPhone and
handset ......................................................28
Cordless handset sPeakerPhone oPeration .
28
switChing Between the sPeakerPhone and
handset earPieCe ......................................28
ConferenCe the external Caller with
Cordless handset and Base ........................28
mEmory .....................................................28
storing a name and numBer in memory ...28
storing a redial numBer..............................29
inserting a Pause in the dialing sequenCe 29
reViewing, Changing or deleting stored
names/numBers .............................................30
dialing a stored numBer .............................30
Chain dialing from memory ........................31
cAllEr id (cid) .........................................32
Call waiting Caller id ................................32
reCeiVing Cid reCords .................................32
storing Cid reCords (in Cid memory) .....33
reViewing Call reCords ...............................33
storing Cid reCords in internal memory 34
dialing a Caller id numBer ........................34
deleting the Current Caller id reCord ...35
deleting all Caller id reCords.................35
Caller id errors ...........................................36
rEmotE AccEss ...........................................36
using the handset.........................................36
answering system indiCator ........................36
memory full ...................................................36
aCCessing the answering system from
another loCation ..........................................37
Changing the seCurity Code .......................37
cHAnging tHE bAttEry ................................38
Battery safety PreCautions .........................38
HEAdsEt And bElt clip opErAtion ...............39
ConneCting an oPtional headset to the
handset ...........................................................39
ConneCting the Belt CliP .............................39
displAy mEssAgEs .......................................40
HAndsEt sound signAls .............................41
troublEsHooting guidE ..............................42
telePhone solutions ................................42
Caller id solutions .................................43
Battery solutions .....................................43
cAusEs of poor rEcEption ..........................44
gEnErAl product cArE ..............................44
wArrAnty AssistAncE .................................45
limitEd wArrAnty ......................................46
indEx .........................................................48
AccEssory informAtion ..............................50
6
For there will be additional handset, charge cradle, belt clip,
battery pack and cover than shown above.
To use this phone, you need an RJ11C type modular telephone
jack, which might look like the one pictured here, installed in your
home. If you don’t have a modular jack, call your local phone
company to nd out how to get one installed.
(for 598xx model)
Make sure your package includes the items shown here.
7
Your cordless phone uses a digital security system to protect against false ringing,
unauthorized access, and charges to your phone line.
• Avoid sources of noise and heat, such as motors, uorescent lighting, microwave
ovens, heating appliances and direct sunlight.
• Avoid areas of excessive dust, moisture and low temperature.
• Avoid other cordless telephones or personal computers.
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the jack is specically
designed for wet locations.
• Never touch non-insulated telephone wires or terminals, unless the telephone line
has been disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
8
:
:
6
5
9
9
9
1. Locate battery and battery door which are packaged together inside a plastic bag
and are separate from the handset.
. Locate the battery compartment on the back of the handset.
3. Plug the battery pack cord into the jack inside the compartment.
4. Insert the battery pack.
5. Close the battery compartment by pushing the door up until it snaps into place.
6. Place the handsets in the charging cradles.
Allow handsets to charge for 16 hours prior to rst use. If you don’t properly charge
the handsets, battery performance is compromised.
black wire
red wire
battery
pack
PRESS DOWN
FIRMLY
10
Choose the best location to install your base and handset charge cradles. Your base
and handset charge cradles should be placed on a level surface such as a desk or
table top, or you may mount the base on a wall.
1. On the base, plug the power adaptor cord into the power jack on the back of the
base and the other into an electrical outlet.
. Plug the handset charge cradle into an electrical outlet.
On the base, plug one end of the straight telephone line cord into the jack on the back
of the base and the other end into a modular wall telephone jack.
Andere Handbücher für 25982EE2
2
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Sprachen:
Andere GE Telefonsystem Handbücher
