GE Druck UPS-III Bedienungsanleitung

Sensing

Druck UPS-III Loop Calibrator

User manual -K0317

www. .com information@itm.com1.800.561.8187

Approved Service Agents

Symbols

This equipment meets the requirements

of all relevant European safety

directives. The equipment carries the

CE mark.

This symbol, on the instrument,

indicates that the user should refer to

the user manual.

Do not dispose of this product as

household waste. Use an approved

organisation that collects and/or

recycles waste electrical and electronic

equipment. For more information:

www. .com information@itm.com1.800.561.8187

1 K0317 Issue No. 3

UPS III Loop Calibrator

Introduction

The Druck UPS III Series of loop calibrators can supply power

(source mode) and produce readings (measure mode) to

perform field calibrations on 2-wire devices. The set-up menu

enables the user to “source” or “measure” in either voltage or

current and to perform continuity tests. These user

instructions include the operation, safety instructions and

installation requirements for the loop calibrator.

Specifications

Accuracy

Values in table below includes temperature effects 17°C to 27°C

Outside these limits .................. 0.003%/°C(0.0015%/°F)

Calibration Reference................ 22°C ±1°C/RH45%±15%

*Resolution 0.001 lsd least significant digits

** Audio + visual rdg reading

Hart® communications...............menu selectable 220

loop resistor

Operating Temperature...... -10°C to 50°C (-14°F to 122°F)

Storage Temperature......... -20°C to 70°C (-4°F to 158°F)

This loop calibrator meets the essential protection

requirements of the relevant EEC directives.

Conforms to......... EN61010, EN 61326-1(1997)+ A1(1998)

Electrical Power Supply

.................................... 4 x 1.5 V alkaline size AA or

Universal power supply {see accessories}

Mode Range Accuracy Remarks

Source mA 0 to 24 mA* 0.01% rdg + 2 lsd V-max. 75V

Source mA +

24V 0 to 24 mA*0.01% rdg + 2 lsd R-max 1k

at 20 mA

Measure mA 0 to 24 mA*0.01% rdg + 2 lsd V-max. 75V

Measure mA

+ 24V 0 to 24 mA*0.01% rdg + 2 lsd R-measure

Measure V 0 to 60V* 0.02% rdg + 4 lsd R-measure

Continuity <100Ω ** -1mA

www. .com information@itm.com1.800.561.8187

K0317 Issue No. 3 2

Physical

Dimensions......................... 77 x 129 x 24 mm(3” x 5” x 1”)

Weight .................................................. 275 grams (9.7 oz.)

Terminals ...................................4 mm sockets {gold plated}

Case ....................................................... High impact ABS

Relative Humidity....................................................0 to 90%

Safety

This symbol, on the loop calibrator, indicates that the

user should refer to the user guide or manual.

Batteries

• Remove batteries from the loop calibrator immediately

when discharged and before storage.

• Dispose of batteries in accordance with local regulations

and battery manufacturers' instructions.

• When storing and transporting batteries make sure they

cannot be short circuited.

Power Supply

The power supply for this loop calibrator can be the internal

non-rechargeable batteries or the external Universal power

supply unit (see accessories).

Battery life >75 hours in measure mode

>18 hours at 12 mA (source mode)

The display shows with low battery power.

Battery Replacement

• Unscrew and remove the securing screw from the battery

panel.

• Replace the batteries, check the polarity of the batteries.

• Refit and secure the battery panel.

Accessories

Assy 305 Test lead set

191-129 Power supply, Universal, 100-240 V a.c. 47-63Hz

38016 Carrying case

38023 Protective rubber boot

www. .com information@itm.com1.800.561.8187

3 K0317 Issue No. 3

OPERATION

Keys

The key switches the calibrator

on and off. Press and hold for 2

seconds.

The key changes the measure or

source operating mode. Pressing the

keys makes menu selections,

sets numerical values and controls

step and ramp functions (up/down).

The select advanced

functions shown on the bottom of the display. When no key is

pressed for 10 minutes, the calibrator times out and switches

off. To disable this automatic time out, select autpower down

in the set-up menu.

www. .com information@itm.com1.800.561.8187

K0317 Issue No. 3 4

Operating Modes

Pressing

switches the instrument on and the display shows

the start-up sequence. Pressing , at this time, the display

shows the information screen:

Pressing , at this time, the display shows the set-up screen:

The calibrator can be used in two modes

measure

source

Measure mode

The display shows the measured value; depending on the

settings made in set-up and advanced settings:

When measuring current pressing enables linear or flow,

pressing enables mA or % (value of 4 to 20 mA or 0 to 20

mA).

When measuring voltage pressing changes the resolution

between 0.00V and 0.000V.

To measure continuity the displays shows an open or closed

switch symbol with an audible signal on switch closure.

F1 Serial number

VERSION

CAL. DATE

HART

BATTERY

Information

Resolution adjust

Contrast adjust

Range 4-20 mA/0-20mA

Source unit mA/%

Hart® ON/OFF

Aut power down ON/OFF

Decimal .,/

Access code menu

Calibration menu

www. .com information@itm.com1.800.561.8187

5 K0317 Issue No. 3

Connect the loop calibrator to the device to be tested:

and Measure mA

Press the mode key and select [Measure mA]. External power

supplies Vmax = 60 V for the loop. The calibrator measures

the current flow of the loop.

Closed loop current measurement from transmitter test

terminal.

*test terminal

Measure mA with 24 V

Press mode key and select [Measure mA and 24V]. The

calibrator supplies 24 V for the loop, maximum 24 mA

www. .com information@itm.com1.800.561.8187

K0317 Issue No. 3 6

Measure Volts

Press mode key and select [Measure V], measure range 60V,

maximum impedance 1 Mohm.

Continuity Test

Press mode key and select [Continuity Test].

Pressing switches the audible signal on/off.

www. .com information@itm.com1.800.561.8187

7 K0317 Issue No. 3

Source Mode

The display shows the source value in mA or % value of 4 to 20

mA or 0 to 20 mA, linear or flow depending on the settings

made in set-up and advanced settings.

Source mA

Press mode key and select [Source mA]. The calibrator

supplies maximum output of: 24 mA; Vmax = 60; receiver input

Rmax = 1kOhm.

Source mA with 24V

Press mode key and select [Source mA and 24V]. The calibrator

supplies maximum loop power of: 24 V and 24 mA.

www. .com information@itm.com1.800.561.8187

K0317 Issue No. 3 8

Advanced Options in a Source mode

Press the key and select mA Source or mA Source & 24V.

Use and

(Enter) to select the function.

Press the key (Advanced) and the display shows:

Linear simulates linear transmitters.

Flow simulates flow transmitters.

Valve simulates valve control signals.

Use and

(Enter) to select the Advanced option:

Advanced

Note: Ramp function not available for valve selection.

Use

to quit.

The display returns to the selected source

mode with the advanced setting available.

Step 25% steps for linear and flow - fixed values for

valve.

Auto-step The same as step with a timed step interval.

Span Check Step between 4 (or 0) mA and 20 mA.

Ramp Automatic ramp between 4 (or 0) mA and 20 mA.

MODE

F1 Lin

Flow

Valve

Step

Auto-step

Span Check

Ramp

Time (M:SS)

Adjust +1/ -1 second

Mode mA source

mA source & 24V select Enter

Advanced

select

www. .com information@itm.com1.800.561.8187

Andere Handbücher für Druck UPS-III

Inhaltsverzeichnis

Andere GE Prüfgeräte Handbücher

GE Druck DPI 832 Bedienungsanleitung

GE FAT Bedienungsanleitung

GE Druck ADTS 405 R Mk2 Bedienungsanleitung

GE SpotChecker Bedienungsanleitung

GE Druck DPI 610 Bedienungsanleitung

GE DPI620G-IS Bedienungsanleitung

GE Druck DPI 610 Bedienungsanleitung

GE Mentor EM Bedienungsanleitung

GE EntelliGuard G Bedienungsanleitung

GE Druck UPS-III Bedienungsanleitung

GE ADTS552F Einrichtungshandbuch

GE Druck DPI 821 Bedienungsanleitung

GE Druck DPI 880 Bedienungsanleitung

GE ADTS 405F Mk2 Einrichtungshandbuch

GE DMS Go+ Bedienungsanleitung

GE Druck DPI 610 Bedienungsanleitung

GE Druck DPI 620 Bedienungsanleitung

GE Druck ADTS 2 Series Gebrauchs- und Pflegehandbuch

GE Druck DPI 150 Bedienungsanleitung

GE PACE5000 Bedienungsanleitung

GE EntelliGuard Bedienungsanleitung

GE Druck ADTS 2 Series Bedienungsanleitung

GE Druck DPI 832 Bedienungsanleitung

GE Druck DPI 620 Genii Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung