GE RAK150VF2 Bedienungsanleitung

SAFETY INFORMATION....................2

OVERVIEW ........................................3

INSTALLATION................................ 4

WIRING DIAGRAMS ..........................8

CONFIGURATION MODE.................10

OPERATING FUNCTIONS............... 13

TROUBLESHOOTING....................... 15

WARRANTY.....................................16

THERMOSTAT

Digital

INSTALLATION INSTRUCTIONS

RAK150VF2

31-5000604 Rev. 1 02-22 GEA

Specifications

WARNING

FIRE AND SHOCK HAZARD

• Always turn off power at the main power supply

before installing, cleaning or removing the

thermostat. Failure to do so could result in

electrical shock hazard.

• Do not use on voltages over 30 VAC. Higher

voltages will damage the thermostat and could cause

shock or fire hazard.

• All wiring must conform to local and national

electrical and building codes.

• Use this thermostat only as described in this manual.

Electrical rating:• 24 VAC (18–30 VAC)

• 1 amp maximum per terminal

• 4 amp maximum total load

Operating temperature range: 40°F–99°F (4°C–37°C)

Temperature set range: 60°F–85°F (15°C–29°C)

Accuracy: ± 1°F (± 0.5°C)

System configurations:

• Factory Setting: 3-stage heat (heat pump low, heat

pump high, resistance heat), 2-stage cool (cool low, cool

high), 2-speed fan

• Alternate Setting: 2-stage heat (heat pump/resistance

heat), 1-stage cool, 2-speed fan

• Alternate Setting: 1-stage heat (resistance heat), 1-stage

cool, 2-speed fan

Terminations: R, C, B, Y1, W, Y2, GL, GH

Wiring: Maximum wiring length is 66ft (20 meters) for

AWG18. Maximum wiring length is 60ft (18 meters) for

AWG20

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING

NOTICE

THERMOSTAT BASE LAYOUT

R C B Y1 W Y2 GL GH

RESET CONFIG

THERMOSTAT CONTROLS

MODE FAN

INTRODUCTION OVERVIEW

Display

Up/Down Buttons

Display Up/Down Buttons Wiring

Channel

Mounting

Hole

Fan

Mode

Mounting

Hole

Configuration

Button

Reset

Button

INSTALLATION INSTRUCTIONS

PACKAGE CONTENTS/TOOLS REQUIRED:

Package includes:

• Thermostat base

• Thermostat cover

• Wiring labels

• Screws

• Wall anchors

Tools needed:

'ULOOZLWKƎELW

• Hammer

• Screwdriver

• Putty

WARNING

ELECTRICAL SHOCK HAZARD — Turn

off power by unplugging the unit or

by removing the fuse or switching the

appropriate circuit breaker to the OFF

position before removing the existing

thermostat. Failure to do so could result in

risk of electric shock.

TO REMOVE EXISTING THERMOSTAT

1. Turn off power to heating and cooling system by

removing the fuse or switching off the appropriate

circuit breaker.

2. Remove cover of old thermostat. This should

expose the wires.

3. Label the existing wires with the enclosed wire

labels before removing wires.

4. After labeling wires, remove wires from wire

terminals.

5. Remove existing thermostat base from wall.

6. Refer to the following section for instructions on

how to install this thermostat.

INSTALLATION INSTRUCTIONS

TO INSTALL THERMOSTAT

IMPORTANT: Thermostat installation

must conform to local and national building and

electrical codes and ordinances.

NOTE: Mount the thermostat about five feet above

the floor. Do not mount the thermostat on an outside

wall, in direct sunlight, behind a door or in an area

affected by a vent or duct.

1. Turn off power to the heating and cooling system

by removing the fuse or switching off the

appropriate circuit breaker.

2. Remove the cover by inserting and twisting a coin

or screwdriver in the slots on the top of

the thermostat.

3. Put thermostat base against the wall where you

plan to mount it. Make sure wires will feed through

the wire opening in the base of the thermostat.

4. With the base level, mark the placement of the

mounting holes.

5. Set thermostat base and cover away from

working area.

6.8VLQJDƎGULOOELWGULOOKROHVLQWKHORFDWLRQV

you have marked for mounting.

7. Use a hammer to tap supplied anchors in

mounting holes.

8. Align thermostat base with mounting holes and

feed the control wires through the wire opening.

INSTALLATION INSTRUCTIONS

TO INSTALL THERMOSTAT (cont.)

9. Seal hole for wires behind thermostat with non-

flammable insulation or putty, or use a wall

plate obtainable from a local hardware or home

building store.

10. Use supplied screws to mount thermostat base to

wall.

11. Insert stripped, labeled wires in matching wire

terminals by pressing on the corresponding

terminal contact. See the “Wiring Diagrams”

section of this manual.

NOTICE

Make sure exposed portion of wires do not touch

other wires.

12. Gently tug wire to be sure of proper connection.

Double check that each wire is connected to the

proper terminal.

13. Replace cover on thermostat by snapping it in

place.

14. Plug the unit in or turn on power to the system at

the main service panel.

15. Test thermostat operation.

INSTALLATION INSTRUCTIONS

WIRING DIAGRAMS

Table 1: Terminals for eight wires. 3-stage heat/2-

stage

cool system

R C B Y1 W Y2 GL GH

24 VAC HOT

24 VAC COMMON

REVERSINGVALVE

STAGE 1 COMPRESSOR

HEAT-ELECTRIC

STAGE 2 COMPRESSOR

INDOORFAN-LOW

INDOORFAN-HIGH

Table 2: Terminals for seven wires. 2-stage

heat/1-stage cool system

WIRING DIAGRAMS

Table 3: Terminals for six wires. 1-stage heat/1-

stage cool system

R C B Y1 W Y2 GL GH

24 VAC HOT

24 VAC COMMON

REVERSINGVALVE

STAGE 1 COMPRESSOR

HEAT-ELECTRIC

INDOORFAN-LOW

INDOORFAN-HIGH

R C B Y1 W Y2 GL GH

24 VAC HOT

24 VAC COMMON

STAGE 1 COMPRESSOR

HEAT-ELECTRIC

INDOORFAN-LOW

INDOORFAN-HIGH

CONFIGURATION MODE

The configuration mode is used to set the RAK150VF2 to match

the heating/cooling system. The default setting of this thermostat

is for 2-stage cooling with a 3-stage heat pump system. For

an alternate configuration, see #7 in the Configuration Mode

Settings below.

To configure the RAK150VF2, perform the following steps:

1. Ensure thermostat is in OFF mode.

2. Remove the thermostat’s front cover.

3. To enter the configuration mode, hold CONFIG for ~ 2 seconds.

4. Once in the configuration mode, press the

button to

change settings within each screen.

-Press the FAN (right) button to advance to the next screen.

- Press the MODE (left) button to return to the previous screen.

NOTE: Hold CONFIG button for ~2 seconds to save changes

and exit configuration menu.

Configuration Mode Settings

The setup screens for Configuration Mode are as follows:

1. Temperature Scale (°F or °C)—Choose Fahrenheit or Celsius.

- Press the

button to select.

- Press the FAN (right) button to advance to the

next screen. NOTE: Default factory setting is

Fahrenheit.

2. Temperature Differential—Stage 1—(1–9°F) (.5-4.5°C)

Set the number of degrees between the “setpoint” temperature

and the “turn on” temperature for first stage.

- Press the

button to set differential

value.

- Press the FAN (right) button to advance to the next screen.

Note: Default factory setting is 1ºF /.5ºC.

3. Temperature Differential—Stage 2 (1–9°F) (.5-4.5°C)

Set the number of degrees between when stage 1 turns on

and stage 2 turns on.

- Press the

button to set differential

value.

- Press the FAN (right) button to advance to the next screen.

- Note: Default factory setting is 1°F/.5°C.

Inhaltsverzeichnis

Sprachen:

Andere GE Thermostat Handbücher

GE PROGRAMMABLE THERMOSTAT Bedienungsanleitung

GE RAK149F2 Originalbetriebsanleitung

GE IS-ZW-TSTAT-300 Bedienungsanleitung

GE RAK348T1 Bedienungsanleitung

GE RAK148F2 Betriebsanleitung

GE 60-909-95 Bedienungsanleitung

GE RAK148H2 Originalbetriebsanleitung

GE RAK148D1 Originalbetriebsanleitung

GE RAK148D2 Originalbetriebsanleitung

GE RAK190V Bedienungsanleitung

GE RAK148D1 Originalbetriebsanleitung

GE PROGRAMMABLE THERMOSTAT Bedienungsanleitung

GE CC-SCSTAT Bedienungsanleitung

GE RARWT Series Originalbetriebsanleitung

GE RAK160W2 Originalbetriebsanleitung

GE RARWT1W Originalbetriebsanleitung

GE RAK148P1 Originalbetriebsanleitung

GE RAK149P2 Originalbetriebsanleitung

GE RAK348T1 Bedienungsanleitung

GE RAK148P2 Originalbetriebsanleitung

GE RAK147P1 Betriebsanleitung

GE RAL163P1 Originalbetriebsanleitung

GE RARWT Series Originalbetriebsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Honeywell

Honeywell T6811 Bedienungsanleitung