GE Monogram ZPK1 Bedienungsanleitung

Installation

Instructions

ZPK1

Icemaker Drain Pump

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all panels before operating.

Failure to do so can result in death

or electrical shock.

IMPORTANT: Connect drain pump to house drain

in accordance with all state and local codes and

ordinances.

Note:

• This drain pump is designed to pump water to a

maximum height of 10 feet.

• To minimize condensation on the drain tube,

insulate the full length of the tube from the pump to

the drain.

Kit Contents:

•Drain Pump

• Drain Tube, 5/8" ID x 4-1/2" (bin to pump reservoir inlet)

• Drain Tube, 3/8" ID x 10 ft. (pump to house drain)

• Vent Tube, 3/8" ID x 32" (pump to cabinet back)

• 3 Cable Clamps (Secures vent tube to back of product)

• 5 Screws, #8 x 1/2" (secures vent hose clamps to back of cabinet

and pump to base plate)

• 2 Hose Clamps, 1/2" (secures vent and drain tube to pump)

• Hose Clamp, 5/8" (secures drain tube to bin)

If Icemaker Is Presently Installed:

• Push the selector switch to OFF.

• Unplug icemaker or disconnect power.

• Shut off water supply. Wait 5 to 10 minutes for the ice

to fall into the storage bin. Remove all ice from the

bin.

• Disconnect the water inlet line from the water valve.

• If the icemaker is installed between cabinets, pull

icemaker out of the opening.

• Unscrew the drain cap from the bottom of the water

pan located inside the storage bin. Allow water to

drain completely. Replace the drain cap.

Disconnect Water Inlet

For connection in Front at Water Valve:

• Remove the 2 screws in the front lower access panel

and the 2 screws from the base grille area. Pull panel

forward to remove.

For Connection at Rear of Icemaker:

•␣ Pull icemaker forward.

• For compression nut, diconnect water line as shown.

• For union between copper tubing, disconnect union.

1/4" Copper Tubing Tubing

Clamp

Ferrule

(Sleeve)

1/4"

Compression Nut

Icemaker Connection

PROCEED TO STEP 1

Water

Inlet

Water

Outlet

-2-

STEP 1 Remove Original Parts

• Remove the 2 screws in the front lower access panel

and the 2 screws from the base grille area. Pull to

remove. Set aside screws and panel.

• Unplug power cord from rear cover.

• Remove screws holding the rear cover. Retain screws.

Carefully pull rear cover away from drain tube.

• Remove old drain tube and clamp attached to bin.

Discard the tube, retain the clamp for re-installation.

• Install the new drain tube with the new 5/8" clamp.

Remove Screws

5/8" Hose Clamp

Drain Tube

(Bin to Pump)

STEP 2 Connect Electrical

A. Position pump at the right side, just outside of the

opening.

B. Remove clamp and screw attached to the icemaker

power cord. Attach the drain pump power cord to

the icemaker base with original clamp and screw.

C. Plug the icemaker power cord into the side of the

pump.

STEP 3 Install New Tubing

A. Attach new drain tube to pump check valve outlet

with new 1/2" hose clamp.

B. Attach vent tube to pump with new 1/2" hose

clamp.

C. Coil icemaker power cord into a 4" dia. coil and

secure with electrical tape. Place the coil over the

top of the pump.

D. Carefully slide the drain pump into the bottom

right side. The front tab on the pump should slip

into the rectangular slot on the icemaker floor. It

may be necessary to tip the pump slightly to engage

the tab.

Note: The pump must be in position before connect-

ing the bin drain tube. See Step 4.

Ground

Wire

Remove Clamp

and Screw

to Release

Icemaker

Power Cord

Pump

Power

Cord

Plug Icemaker

Power Cord

Into Pump

Position Pump

Just Outside

of Opening

Bin

Drain

Inlet Vent Tube

Connection

Slide Pump Tab

Into Slot

Coil Icemaker

Power Cord

Drain Tube (Pump

to Household Drain)

-3-

STEP 4 Install Bin Drain Tube

A. Attach drain tube from bin to pump with

original hose clamp from old drain tube.

B. Secure the pump to the base with the 2

supplied screws.

STEP 5 Secure Vent Tube

• Place rear cover against the back of the icemaker.

Route the vent tube and drain tube through cutouts

in the rear cover.

• Secure rear cover with original screws.

• Secure vent tube to the back of the icemaker with the

3 clamps and 3 remaining screws.

• Route drain tube to house drain.

Vent Tube

Mounting Clamp

and Screw

Vent Tube

Original Icemaker

Power Cord

Pump Mounting Screws

Connect

Bin Drain

Tube

STEP 7 Finalize Installation

• Connect power.

• Push selector switch to ON.

• Wait for rinsing cycle, approximately 5 minutes, to be

sure the icemaker is operating properly.

Pub. No. 49-60155 SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE DWG. NO. 197D4493P001

(N.D. 305) 11/01

STEP 6 Connect Water Supply

• Feed water supply tubing through one of the two

access holes in the rear cover.

• Slide the icemaker into its permanent location.

IMPORTANT: Check to be sure water and drain lines

do not kink or bind. This could interfere with

icemaker operation.

• Bend the tubing to meet the connection at the water

valve inlet at the front.

• Remove the water valve inlet cover and attach copper

tubing with a compression nut and sleeve.

• Check to be sure copper tubing does not touch the

side wall or other parts inside the cabinet.

• Turn on the water and check all connections for

leaks.

Water

Line

Access

Holes

Water

Inlet

Water

Outlet

• Check to be sure copper tubing does not touch the

side wall or other parts inside the cabinet.

• Turn on the water and check all connections for

leaks.

For connection in Front at Water Valve:

• For threaded connection, use ferrule and compres-

sion nut to secure the line as shown on page 1.

• For water tube exiting rear access cover, connect

water line using 1/4" union or coupling.

For Water Connection at Rear:

Water

Supply

Line

Drain Hose

From Drain

Pump

Vent Hose

From Drain Pump

Coupling

(Not Supplied)

Nut

(Supplied)

Ferrule

(Not Supplied)

Line to

Icemaker

Nut

(Supplied)

Andere GE Wasserpumpe Handbücher

GE PV411A Bedienungsanleitung

GE OSMONICS TONKAFLO SS1000 SERIES Bedienungsanleitung

GE UPK3 Bedienungsanleitung

GE Druck PV210 Bedienungsanleitung

GE UPK4 Bedienungsanleitung

GE PV411A Bedienungsanleitung

GE OSMONICS TONKAFLO SS Series Bedienungsanleitung

GE Peristaltic Pump P-1 Bedienungsanleitung

GE OSMONICS TONKAFLO QS1800V Series Bedienungsanleitung

GE 5514 Bedienungsanleitung

GE UPK3 Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung