GEA HA4 Bedienungsanleitung

09791-01.2015-DGbFEIRu

engineering for a better world

GEA Bock Compressor HA4

Assembly instructions

HA4/310-4 HAX4/310-4

HA4/385-4 HAX4/385-4

HA4/465-4 HAX4/465-4

HA4/555-4 HAX4/555-4

HA4/650-4 HAX4/650-4

09791-01.2015-DGbFEIRu

About these instructions

Read these instructions before assembly and before using the compressor. This will avoid misunder-

standings and prevent damage. Improper assembly and use of the compressor can result in serious

or fatal injury.

Observe the safety instructions contained in these instructions.

These instructions must be passed onto the end customer along with the unit in which the compres-

sor is installed.

GEA Bock GmbH

72636 Frickenhausen

GEA Bock GmbH

Benzstraße 7

72636 Frickenhausen

Germany

Telephone +49 7022 9454 0

Fax +49 7022 9454 137

[email protected]

www.gea.com

Manufacturer

Contact

09791-01.2015-DGbFEIRu

Contents Page

1 Safety 4

 1.1 Identicationofsafetyinstructions

 1.2 Qualicationsrequiredofpersonnel

1.3 General safety instructions

1.4 Intended use

2 Product description 6

2.1 Short description

2.2 Name plate

2.3 Type key

3 Areas of application 8

3.1 Refrigerants

3.2 Oil charge

3.3 Limits of application

4Compressor assembly 10

4.1 Storage and transport

4.2 Setting up

4.3 Pipe connections

4.4 Pipes

4.5 Laying suction and pressure lines

4.6 Operating the shut-off valves

4.7 Operating mode of the lockable service connections

5 Electrical connection 13

5.1 Information for contactor and motor contactor selection

5.2 Standard motor, design for direct or part winding start

5.3 Basic circuit diagram for part winding start with standard motor

5.4 Special motor: design for direct or star-delta start

5.5 Basic circuit diagram for star-delta start with special motor

5.6 Electronic trigger unit MP 10

5.7 Connecting the trigger unit MP 10

5.8 Functional test of the trigger unit MP 10

5.9 Oil sump heater (accessories)

5.10 Fan motor

6 Commissioning 23

6.1 Preparations for start-up

6.2 Pressure strength test

6.3 Leak test

6.4 Evacuation

6.5 Refrigerant charge

6.6 Start-up

6.7 Avoiding slugging

6.8 Connection of oil level regulator

7 Maintenance 25

7.1 Preparation

7.2 Work to be carried out

7.3 Spare parts recommendation

7.4 Accessories

7.5 Extract from the lubricants table

7.6 Decommissioning

8 Technical data 27

9 Dimensions and connections 28

10 Declaration of conformity and installation 30

11 Service 31

09791-01.2015-DGbFEIRu

1|Safety

1.2 Qualicationsrequiredofpersonnel

1.3 General safety instructions

WARNING! Inadequately qualied personnel poses the risk of accidents, the

consequence being serious or fatal injury. Work on compressors

mustthereforeonlybeperformedbypersonnelwiththequalica-

tions listed below:

• For example, a refrigeration technician, refrigeration mechatron-

ics engineer. As well as professions with comparable training, which

enable personnel to assemble, install, maintain and repair refrigeration

and air-conditioning systems. Personnel must be capable of assessing

thework to be carried out and recognising any potential dangers.

WARNING! • Refrigerating compressors are pressurised machines and

thereforerequireparticularcautionandcareinhandling.

• Risk of burns! Depending on the operating conditions, surface

temperatures of over 60 °C on the pressure side or below 0 °C on

the suction side can be reached.

• The maximum permissible overpressure must not be exceeded,

even for testing purposes.

1.1 Identicationofsafetyinstructions:

DANGER! Indicatesadangeroussituationwhich,ifnot

 avoided,willcauseimmediatefatalorseriousinjury.

WARNING!

 Indicatesadangeroussituationwhich,ifnot

 avoided,maycausefatalorseriousinjury.

CAUTION!

 Indicatesadangeroussituationwhich,ifnot

 avoided,maycausefairlysevereorminorinjury.

ATTENTION! Indicatesasituationwhich,ifnot

 avoided,maycausepropertydamage.

INFO! Importantinformationortipsonsimplifyingwork.

09791-01.2015-DGbFEIRu

1|Safety

These assembly instructions describe the standard version of the HA4 manufactured by GEA Bock.

The compressor is intended for use in refrigeration systems in compliance with the limits of applica-

tion.Onlytherefrigerantspeciedintheseinstructionsmaybeused.

Any other use of the compressor is prohibited!

The GEA Bock refrigerating compressor named in the title is intended for installing in a machine

(within the EU according to the EU Directives 2006/42/EC Machinery Directive, 97/23/EC Pressure

EquipmentDirectiveand2006/95/EC–LowVoltageDirective).

Commissioning is only permissible if the compressor has been installed in accordance with these

assembly instructions and the entire system into which it is integrated has been inspected and

approved in accordance with legal regulations.

1.4 Intended use

WARNING! The compressor may not be used in potentially

explosive environments!

09791-01.2015-DGbFEIRu

2|Product description

• Semi-hermetic four-cylinder reciprocating compressor with oil pump lubrication.

• Flange-mounted drive motor on the compressor case.

• Specially or deep cooling with air-cooled motor and direct suction at the cylinder.

Name plate

Fig. 1

2.1 Brief description

Oil sight glass

Valveplate Cylinder

cover

Terminal box

Suction shut-

off valve

Dimension and connection values can be found in Chapter 9

Transport eyelet

Discharge

shut-off valve

Oil pump

Air guide hood

with fan

Drive section

09791-01.2015-DGbFEIRu

2|Product description

HA 4 650- 4

Fig. 2

2.2 Name plate (example)

2.3 Typekey (example)

¹) HA - Hermetic Air-cooled (for deep-freezing)

²) X - Ester oil charge (HFC refrigerant, e.g. R404A/R507)

Number of poles

Swept volume

Size

Oil charge ²)

Series ¹)

1 Typedesignation 6 Voltage,circuit,frequency

2 Machine number 7 Nominal rotation speed

3 maximum operating current 8 Displacement

4 Startingcurrent(rotorblocked) 9 Voltage,circuit,frequency

Y: Part winding 1 10 Nominal rotation speed

YY: Part windings 1 and 2 11 Displacement

5 ND LP:

max. admissible operating pressur

e 12 Oiltypelledatthefactory

(g) Low pressure side 13 Terminal box protection type

HD (HP):

max. admissible operating

Electrical accessories can change

pressur

e(g) High pressure side the IP protection class!

Observe the limits of application

diagrams!

50 Hz

}

60 Hz

}

HAX4/650-4

AS35830-006

26.0 A

107 A 140 A

56,6

67,9

SE 55

GEA Bock GmbH

72636 Frickenhausen, Germany

09791-01.2015-DGbFEIRu

3|Areas of application

ATTENTION! Compressor operation is possible within the operating limits

shown in the diagrams. Please note the signicance

of the shaded areas. Thresholds should not be selected as design

or continuous operation points.

- Max. permissible ambient temperature 45 °C

- Max. permissible discharge end temperature 140 °C

    -Max.permissibleswitchingfrequency12x/h.

- A minimum running time of 3 min. steady-state condition

(continuous operation) must be achieved.

For operation with capacity regulator:

- The suction gas superheat temperature may need to be reduced

or set individually when operating near to the threshold.

Foroperationwithfrequencyconverter:

- The maximum current and power consumption must not be

exceeded. Inthecaseofoperation abovethemains frequency,

the application limit can therefore be limited.

When operating in the vacuum range, there is a danger of air

enteringonthesuctionside.Thiscancausechemicalreactions,

a pressure rise in the condenser and an elevated compressed-gas

temperature. Prevent the ingress of air at all costs!

 Thecompressorsarelledatthefactorywiththefollowingoiltype:

- for R404A/R507 FUCHS Reniso Triton SE 55

- for R22 FUCHS Reniso SP 46

Compressors with ester oil charge (FUCHS Reniso Triton SE 55) are marked with an X in the type

designation (e.g. HAX4/650-4).

3.1 Refrigerants

• HFKW / HFC: R404A/R507

• (H)FCKW / (H)CFC: R22

3.2 Oil charge

3.3 Limits of application

INFO! Forrefilling,werecommendtheaboveoiltypes.

Alternatives: seelubricantstable,Chapter7.5.

The oil level must be in the

visible part of the sight glass;

damage to the compressor is

possible if overfilled or under-

filled!

ATTENTION!

Fig. 3

max. oil level

min. oil level

09791-01.2015-DGbFEIRu

Unlimited

application range

Reduced suction gas

temperature

Evaporation temperature (°C)

Condensing temperature (°C)

Suction gas superheat (K)

Suction gas temperature (°C)

Fig. 5

Fig. 4

3|Areas of application

R404A

R507

R22

Design for other

areasonrequest

Max. permissible operating

pressure (LP/HP)1): 19/28 bar

1) LP = Low pressure

HP = High pressure

09791-01.2015-DGbFEIRu

4|Compressor assembly

INFO! Newcompressorsarefactory-lledwithinertgas(3barnitrogen).

Leave this service charge in the compressor for as long as possible

and prevent the ingress of air.

  Check the compressor for transport damage before starting any

 work.

 Setuponanevensurfaceorframewithsufcientload-

bearing capacity.

Single compressor preferably on vibration damper.

Duplex and parallel circuits always rigid.

 Provideadequateclearanceformaintenancework.

 Ensureadequatecompressorventilation.

The compressor must not be in the air stream to another

component of the refrigeration system (e.g. condenser).

The cooling of the drive motor must be reliable guaranteed.

Do not use in a corrosive, dusty, damp atmosphere or a

combustible environment.

Fig. 8

Fig. 9

Fig. 10

Tol.-Ang. DIN ISO 2768-mK

Ra Rz

Maß

Passung

Freigabe

Alternativbezug:

Baumustergeprüft

Teil inaktiv

Lieferantenzeichnung

K.-Auftrag:

PL:

Zeichnung ungültig

Entwicklungsstand

Teil keine Serie

120

400

±0.5

über 0.5

bis 6

Benzstraße 7 - 72636 Frickenhausen - Germany - www.bock.de

Unbemaßte Radien:

Diese Zeichnung ist unser Eigentum!

Sie darf ohne unsere Genehmigung weder nach-

gebildet, vervielfältigt, oder Dritten Personen zu-

gänglich gemacht werden. Der Nachbau nach

dieser Zeichnung, oder an Hand der nach dieser

Zeichnung hergestellten Gegenstände durch den

Abnehmer oder Dritte ist nicht gestattet.

Wir behalten uns alle Rechte, gemäß DIN ISO 16016

an dieser Zeichnung vor.

Bearb.

Datum

Änderungs-Nr.

Werkstoff:

Ausgangsteil, bzw. Rohteil:

Gepr.

Name

Datum

19.04.

Werkstückkanten

DIN ISO 13715

Ersatz für:

Ersetzt durch:

Erstellt

2010

Geprüft

Kurz

Zone

1/x

Oberflächenbehandlung / Härte:

Blatt:

Änderungsbeschreibung

400

Benennung:

±0.8

1000

±0.3

120

±0.2

Zeichn.-Nr. Teile-Nr.

Oberflächenangaben ISO 1302

x.xxxx-xxxxx.x

Zust.

Gußtoleranzen:

Gewicht: (kg)

±0.1

Maßstab:

1:1

Wasserwaage

für Indesign

Der Lieferant muß sicherstellen, dass die Ware in

einwandfreiem Zustand angeliefert wird (Korrosions-

schutz, Verpackung für sicheren Transport).

Rz 25

Rz 160

0,05

Rz 1,6

0,3

0,7

1,6

Rz 16

6,3

Rz 63

Rz 6,3

Rz 12,5

F:\user\kurz\3D Sachen\3D Teile\Zeichnungen\Wasserwaage

4.2 Setting up

4.1 Storage and transport

Use transport eyelet.

Do not lift manually!

Use lifting gear!

Storage at (-30°C) - (+70°C), maximum permissible relative humidity

10% - 95%, no condensation

Do not store in a corrosive, dusty, vaporous atmosphere or in a com-

bustible environment.

Fig. 7

Fig. 6

ATTENTION! Attachments(e.g.pipeholders,additionalunits,fasteningparts,

etc.) directly to the compressor are not permissible!

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere GEA Luftkompressor Handbücher

GEA

GEA F Series Bedienungsanleitung

GEA

GEA HG6/1080-4 Bedienungsanleitung

GEA

GEA HGX4 CO2 Series Bedienungsanleitung

GEA

GEA HG12P Bedienungsanleitung

GEA

GEA HG4 Bedienungsanleitung

GEA

GEA FK20 Bedienungsanleitung

GEA

GEA HGX6 R134a series Bedienungsanleitung

GEA

GEA Bock HGX46 CO2 T Series Bedienungsanleitung

GEA

GEA Bock HG22P A Bedienungsanleitung

GEA

GEA HGX34/110-4 ML CO2 T Bedienungsanleitung

GEA

GEA HG34P/215-4 Bedienungsanleitung

GEA

GEA GEA Bock HG66e Series Bedienungsanleitung

GEA

GEA Grasso VHS Series Bedienungsanleitung

GEA

GEA Grasso Bedienungsanleitung

GEA

GEA Searle NSQ Series Bedienungsanleitung

GEA

GEA Bock HGX2 CO2 T Series Bedienungsanleitung

GEA

GEA FK50/460 N Bedienungsanleitung

GEA

GEA HGX46/280-4 ML CO2T Bedienungsanleitung

GEA

GEA HGX4 R134a Bedienungsanleitung

GEA

GEA Grasso RC9 Series Bedienungsanleitung

GEA

GEA Bock HGZ Series Bedienungsanleitung

GEA

GEA HG5/725-4 Bedienungsanleitung

GEA

GEA HG88e series Bedienungsanleitung

GEA

GEA HG76e/1620-4 Bedienungsanleitung

Beliebte Luftkompressor Handbücher anderer Marken

Sparmax

Sparmax DC-25XR Bedienungsanleitung

KAESER

KAESER M122 Bedienungsanleitung

GMC

GMC GAC1500 Bedienungsanleitung

Briggs & Stratton

Briggs & Stratton Air Compressor Bedienungsanleitung

Fini

Fini F3GST2TK Bedienungsanleitung

Industrial Air

Industrial Air CP1580325 Programmierhandbuch

Campbell Hausfeld

Campbell Hausfeld RP3300 Kurzanleitung

Ingersoll-Rand

Ingersoll-Rand UP6 20 HP Bedienungsanleitung

Hitachi

Hitachi EC99S Bedienerhandbuch

Parkside

Parkside PKO 270 A1 Bedienungsanleitung

Sullair

Sullair 185 Bedienungsanleitung

Clas Ohlson

Clas Ohlson QIE-ZTH-15 Bedienungsanleitung

Ferm

Ferm CRM1046 Bedienungsanleitung

BE AC153 Bedienungsanleitung

RIDGID

RIDGID OF25150A Bedienungsanleitung

Johnson Controls

Johnson Controls QUANTUM LX Handbuch

Sears

Sears Craftsman 919.167463 Bedienungsanleitung

Ring Automotive

Ring Automotive RAC700 Bedienungsanleitung