GEA HG22P Series Bedienungsanleitung

09637-06.2015-DGbFEIRu

engineering for a better world

GEA Bock Compressor HG22P

Assembly instructions

HG22P/125-4 HG22P/125-4 S HGX22P/125-4 HGX22P/125-4 S

HG22P/160-4 HG22P/160-4 S HGX22P/160-4 HGX22P/160-4 S

HG22P/190-4 HG22P/190-4 S HGX22P/190-4 HGX22P/190-4 S

09637-06.2015-DGbFEIRu

About these instructions

Read these instructions before assembly and before using the compressor. This will avoid misunder-

standings and prevent damage. Improper assembly and use of the compressor can result in serious

or fatal injury.

Observe the safety instructions contained in these instructions.

These instructions must be passed onto the end customer along with the unit in which the compres-

sor is installed.

GEA Bock GmbH

72636 Frickenhausen

GEA Bock GmbH

Benzstraße 7

72636 Frickenhausen

Germany

Telephone +49 7022 9454 0

Fax +49 7022 9454 137

[email protected]

www.gea.com

Manufacturer

Contact

Contents Page

1 Safety 4

 1.1 Identicationofsafetyinstructions

 1.2 Qualicationsrequiredofpersonnel

1.3 General safety instructions

1.4 Intended use

2 Product description 6

2.1 Short description

2.2 Name plate

2.3 Type key

09637-06.2015-DGbFEIRu

Contents Page

3 Areas of application 8

3.1 Refrigerants

3.2 Oil charge

3.3 Limits of application

4Compressor assembly 10

4.1 Storage and transport

4.2 Setting up

4.3 Pipe connections

4.4 Pipes

4.5 Laying suction and pressure lines

4.6 Operating the shut-off valves

4.7 Operating mode of the lockable service connections

5 Electrical connection 13

5.1 Information for contactor and motor contactor selection

5.2 Connection of the driving motor

5.3 Circuit diagram for direct start 230 V Δ/ 400 V Y --> with MP10

5.4 Electronic trigger unit MP10

5.5 Connection of the electronic trigger unit MP10

5.6 Functional test of the electronic trigger unit MP10

5.7 Circuit diagram for direct start 230 V Δ/ 400 V Y --> with INT69 G

5.8 Electronic trigger unit INT69 G

5.9 Connection of the electronic trigger unit INT69 G

5.10 Functional test of the electronic trigger unit INT69 G

5.11 Start unloader

6 Commissioning 22

6.1 Preparations for start-up

6.2 Pressure strength test

6.3 Leak test

6.4 Evacuation

6.5 Refrigerant charge

6.6 Start-up

6.7 Avoiding slugging

6.8 Connection of oil level regulator

7 Maintenance 24

7.1 Preparation

7.2 Work to be carried out

7.3 Spare parts recommendation

7.4 Accessories

7.5 Extract from the lubricants table

7.6 Decommissioning

8 Technical data 26

9 Dimensions and connections 27

10 Declaration of conformity and installation 28

11 Service 29

09637-06.2015-DGbFEIRu

1|Safety

1.2 Qualicationsrequiredofpersonnel

1.3 General safety instructions

WARNING! Inadequately qualied personnel poses the risk of accidents, the

consequence being serious or fatal injury. Work on compressors

mustthereforeonlybeperformedbypersonnelwiththequalica-

tions listed below:

• For example, a refrigeration technician, refrigeration mechatron-

ics engineer. As well as professions with comparable training, which

enable personnel to assemble, install, maintain and repair refrigeration

and air-conditioning systems. Personnel must be capable of assessing

thework to be carried out and recognising any potential dangers.

WARNING! • Refrigerating compressors are pressurised machines and

thereforerequireparticularcautionandcareinhandling.

• Risk of burns! Depending on the operating conditions, surface

temperatures of over 60 °C on the pressure side or below 0 °C on

the suction side can be reached.

• The maximum permissible overpressure must not be exceeded,

even for testing purposes.

1.1 Identicationofsafetyinstructions:

DANGER! Indicatesadangeroussituationwhich,ifnot

 avoided,willcauseimmediatefatalorseriousinjury.

WARNING!

 Indicatesadangeroussituationwhich,ifnot

 avoided,maycausefatalorseriousinjury.

CAUTION!

 Indicatesadangeroussituationwhich,ifnot

 avoided,maycausefairlysevereorminorinjury.

ATTENTION! Indicatesasituationwhich,ifnot

 avoided,maycausepropertydamage.

INFO! Importantinformationortipsonsimplifyingwork.

09637-06.2015-DGbFEIRu

1|Safety

These assembly instructions describe the standard version of the HG22P manufactured by GEA

Bock. The compressor is intended for use in refrigeration systems in compliance with the limits of

application.Onlytherefrigerantspeciedintheseinstructionsmaybeused.

Any other use of the compressor is prohibited!

The GEA Bock refrigerating compressor named in the title is intended for installing in a machine

(within the EU according to the EU Directives 2006/42/EC Machinery Directive, 97/23/EC Pressure

EquipmentDirectiveand2006/95/EC–LowVoltageDirective).

Commissioning is only permissible if the compressor has been installed in accordance with these

assembly instructions and the entire system into which it is integrated has been inspected and

approved in accordance with legal regulations.

1.4 Intended use

WARNING! The compressor may not be used in potentially

explosive environments!

09637-06.2015-DGbFEIRu

2|Product description

• Semi-hermetic two-cylinder reciprocating compressor with oil pump lubrication.

• Suction gas cooled drive motor.

2.1 Short description

Name plate

Fig. 1

Fig. 2

Oil sight glass

Cylinder cover

Oil pump

Terminal box

Suction

shut-off valve

Drive section

Motor section

Dimension and connection values can be found in Chapter 9

Transport eyelet

Valve plate

Discharge

shut-off valve

09637-06.2015-DGbFEIRu

Typschild (Beispiel)

513

1 Typbezeichnung

2 Maschinennummer

3 maximaler Betriebsstrom

4 Anlaufstrom (Rotor blockiert)

5 ND (LP): max. zulässiger Stillstandsdruck

Saugseite

HD (HP): max. zulässiger Betriebsdruck

Hochdruckseite

Einsatzgrenzendiagramme beachten!

50 Hz

60 Hz

6 Spannung, Schaltung, Frequenz

7 Nenndrehzahl

8 Hubvolumen

9 Spannung, Schaltung, Frequenz

10 Nenndrehzahl

11 Hubvolumen

12 Werkseitig eingefüllte Ölsorte

13 Schutzart Klemmenkasten

HGX22P/190-4

SE 55

AS35830A001

GEA Bock GmbH

72636 Frickenhausen, Germany

2|Product description

2.2 Name plate (example)

1 Typedesignation 6 Voltage,circuit,frequency

2 Machine number 7 Nominal rotation speed

3 maximum operating current 8 Displacement

4 Startingcurrent(rotorblocked) 9 Voltage,circuit,frequency

5 ND(LP):max.admissibleoperating 10 Nominalrotationspeed

pressure (g)Low pressure side 11 Displacement

 HD(HP):

max. admissible operating

 12 Oiltypelledatthefactory

pressur

e(g)High pressure side 13 Terminal box protection type

Observe the limits of application Electrical accessories can change

diagrams! the IP protection class!

50 Hz

}

60 Hz

}

Fig. 3

HG 22 P 190-4 SX

2.3 Typekey (example)

¹)HG-HermeticGas-cooled(suctiongas-cooled)forthenormal-/airconditioningapplications

²)X

-Esteroilcharge(HFCrefrigerant,e.g.R134a,R404A/R507,R407C)

³) Additional declaration for Pluscom compressors

4)S - More powerful motor, e.g. for air-conditioning applications

Motor variant 4)

Number of poles

Swept volume

³)

Numbers of cylinders

Size

Oil charge ²)

Series ¹)

09637-06.2015-DGbFEIRu

3|Areas of application

ATTENTION! Compressor operation is possible within the operating limits

shown in the diagrams. Please note the signicance

of the shaded areas. Thresholds should not be selected as design

or continuous operation points.

- Permissible ambient temperature (-20°C) - (+60°C)

- Max. permissible discharge end temperature 140 °C

    -Max.permissibleswitchingfrequency8x/h.

- A minimum running time of 3 min. steady-state condition

(continuous operation) must be achieved.

For operation with additional cooling:

- Use only oils that are highly thermally stable.

- Avoid continuous operation near the limits.

Foroperationwithfrequencyconverter:

- The maximum current and power consumption must not be

exceeded. Inthecaseofoperationabovethemainsfrequency,

the application limit can therefore be limited.

When operating in the vacuum range, there is a danger of air

enteringonthesuctionside.Thiscancausechemicalreactions,

a pressure rise in the condenser and an elevated compressed-gas

temperature. Prevent the ingress of air at all costs!

Thecompressorsarelledatthefactorywiththefollowingoiltype:

- for R134a, R404A/R507, R407C FUCHS Reniso Triton SE 55

- for R22 FUCHS Reniso SP 46

Compressorswithesteroilcharge(FUCHSRenisoTritonSE55)aremarkedwithanXinthetype

designation (e.g. HGX22P/190-4).

3.1 Refrigerants

• HFKW/HFC:  R134a, R404A/R507, R407C

• (H)FCKW/(H)CFC: R22

3.2 Oil charge

3.3 Limits of application

INFO! Forrefilling,werecommendtheaboveoiltypes.

Alternatives: seelubricantstable,Chapter7.5.

The oil level must be in the

visible part of the sight

glass; damage to the com-

pressor is possible if over-

filled or underfilled!

ATTENTION!max.

min.

0,7 Ltr.

oil level

Fig. 4

09637-06.2015-DGbFEIRu

Evaporationtemperature(°C)

Condensingtemperature(°C)

Suctiongassuperheat(K)

Suctiongastemperature(°C)

Design for other

areasonrequest

R134a

R407C

R404A/R507

R22

Fig. 5

Fig. 6

Fig. 7

Fig. 8

Unlimited application range

Supplementary cooling or

reduced suction gas temperature

Supplementary cooling and

reduced suction gas temperature

Motor version S

(morepowerfulmotor)

Max. permissible operating

pressure (LP/HP)1): 19/28 bar

1) LP = Low pressure

HP = High pressure

09637-06.2015-DGbFEIRu

4|Compressor assembly

INFO! Newcompressorsarefactory-lledwithinertgas(3barnitrogen).

Leave this service charge in the compressor for as long as possible

and prevent the ingress of air.

  Check the compressor for transport damage before starting any

 work.

4.3 Pipe connections

ATTENTION! Do not solder as long as the compressor is under pressure.

Superheating can damage the valve. Remove the pipe supports

therefore from the valve for soldering and accordingly cool the

valve body during and after soldering.

Only solder using inert gas to inhibit oxidation products (scale).

4.1 Storage and transport

Use transport eyelet.

Do not lift manually!

Use lifting gear!

 Storageat(-30°C)-(+70°C),maximumpermissiblerelativehumidity

10% - 95%, no condensation

Do not store in a corrosive, dusty, vaporous atmosphere or in a com-

bustible environment.

Fig. 10

Fig. 9

ATTENTION! Attachments(e.g.pipeholders,additionalunits,fasteningparts,

etc.) directly to the compressor are not permissible!

4.2 Setting up

 Setuponanevensurfaceorframewithsufcientload-

bearing capacity.

Single compressor preferably on vibration damper.

Duplex and parallel circuits always rigid.

 Provideadequateclearanceformaintenancework.

 Ensureadequatecompressorventilation.

Do not use in a corrosive, dusty, damp atmosphere or a

combustible environment.

Fig. 11

Fig. 12

Fig. 13

Tol.-Ang. DIN ISO 2768-mK

Ra Rz

Maß

Passung

Freigabe

Alternativbezug:

Baumustergeprüft

Teil inaktiv

Lieferantenzeichnung

K.-Auftrag:

PL:

Zeichnung ungültig

Entwicklungsstand

Teil keine Serie

120

400

±0.5

über 0.5

bis 6

Benzstraße 7 - 72636 Frickenhausen - Germany - www.bock.de

Unbemaßte Radien:

Diese Zeichnung ist unser Eigentum!

Sie darf ohne unsere Genehmigung weder nach-

gebildet, vervielfältigt, oder Dritten Personen zu-

gänglich gemacht werden. Der Nachbau nach

dieser Zeichnung, oder an Hand der nach dieser

Zeichnung hergestellten Gegenstände durch den

Abnehmer oder Dritte ist nicht gestattet.

Wir behalten uns alle Rechte, gemäß DIN ISO 16016

an dieser Zeichnung vor.

Bearb.

Datum

Änderungs-Nr.

Werkstoff:

Ausgangsteil, bzw. Rohteil:

Gepr.

Name

Datum

19.04.

Werkstückkanten

DIN ISO 13715

Ersatz für:

Ersetzt durch:

Erstellt

2010

Geprüft

Kurz

Zone

1/x

Oberflächenbehandlung / Härte:

Blatt:

Änderungsbeschreibung

400

Benennung:

±0.8

1000

±0.3

120

±0.2

Zeichn.-Nr. Teile-Nr.

Oberflächenangaben ISO 1302

x.xxxx-xxxxx.x

Zust.

Gußtoleranzen:

Gewicht: (kg)

±0.1

Maßstab:

1:1

Wasserwaage

für Indesign

Der Lieferant muß sicherstellen, dass die Ware in

einwandfreiem Zustand angeliefert wird (Korrosions-

schutz, Verpackung für sicheren Transport).

Rz 25

Rz 160

0,05

Rz 1,6

0,3

0,7

1,6

Rz 16

6,3

Rz 63

Rz 6,3

Rz 12,5

F:\user\kurz\3D Sachen\3D Teile\Zeichnungen\Wasserwaage

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere GEA Luftkompressor Handbücher

GEA

GEA Bock HGX2 CO2 T Series Bedienungsanleitung

GEA

GEA Bock HG8 Series Bedienungsanleitung

GEA

GEA HG4/310-4 Bedienungsanleitung

GEA

GEA Bock F76 Series Bedienungsanleitung

GEA

GEA F Series Bedienungsanleitung

GEA

GEA HGX34/130-4 ML CO2 T Bedienungsanleitung

GEA

GEA Bock HG8 Series Bedienungsanleitung

GEA

GEA pluscom Bock EX-HG12P Bedienungsanleitung

GEA

GEA HG22e/160-4 Bedienungsanleitung

GEA

GEA Bock HGX46 CO2 T Series Bedienungsanleitung

GEA

GEA HGX46/280-4 ML CO2T Bedienungsanleitung

GEA

GEA Grasso RC9 Series Bedienungsanleitung

GEA

GEA HA4 Bedienungsanleitung

GEA

GEA Grasso M-Series Bedienungsanleitung

GEA

GEA FK40/560 N Bedienungsanleitung

GEA

GEA HGX34/110-4 ML CO2 T Bedienungsanleitung

GEA

GEA HGX4 CO2 Series Bedienungsanleitung

GEA

GEA Grasso 5 Bedienungsanleitung

GEA

GEA HGX12e S CO2 Bedienungsanleitung

GEA

GEA Grasso Bedienungsanleitung

GEA

GEA HGX34 CO2 T Series Bedienungsanleitung

GEA

GEA HG22e/125-4 Bedienungsanleitung

GEA

GEA HG4 Bedienungsanleitung

GEA

GEA HG76e/1620-4 Bedienungsanleitung

Beliebte Luftkompressor Handbücher anderer Marken

Sparmax

Sparmax DC-25XR Bedienungsanleitung

KAESER

KAESER M122 Bedienungsanleitung

GMC

GMC GAC1500 Bedienungsanleitung

Briggs & Stratton

Briggs & Stratton Air Compressor Bedienungsanleitung

Fini

Fini F3GST2TK Bedienungsanleitung

Industrial Air

Industrial Air CP1580325 Programmierhandbuch

Campbell Hausfeld

Campbell Hausfeld RP3300 Kurzanleitung

Ingersoll-Rand

Ingersoll-Rand UP6 20 HP Bedienungsanleitung

Hitachi

Hitachi EC99S Bedienerhandbuch

Parkside

Parkside PKO 270 A1 Bedienungsanleitung

Sullair

Sullair 185 Bedienungsanleitung

Clas Ohlson

Clas Ohlson QIE-ZTH-15 Bedienungsanleitung

Ferm

Ferm CRM1046 Bedienungsanleitung

BE AC153 Bedienungsanleitung

RIDGID

RIDGID OF25150A Bedienungsanleitung

Johnson Controls

Johnson Controls QUANTUM LX Handbuch

Sears

Sears Craftsman 919.167463 Bedienungsanleitung

Ring Automotive

Ring Automotive RAC700 Bedienungsanleitung