Gefen EXT-HD-1000 Bedienungsanleitung
®
www.gefen.com
HD-1000
Extender
EXT-HD-1000
User Manual
Technical Support:
Telephone (818) 772-9100
(800) 545-6900
Fax (818) 772-9120
Technical Support Hours:
8:00 AM to 5:00 PM Monday through Friday PST
Write To:
Gefen Inc.
c/o Customer Service
20600 Nordhoff Street
Chatsworth, CA 91311
www.gefen.com
Notice
Gefen, LLC reserves the right to make changes in the hardware, packaging, and
any accompanying documentation without prior written notice.
HDMI, the HDMI Logo, and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing in the United States and
other countries.
HD-1000 is a trademark of Gefen, LLC
© 2011 Gefen, LLC. All rights reserved.
All trademarks are the property of their respective owners.
ASKING FOR ASSISTANCE
Rev X4
TABLE OF CONTENTS
1. Introduction / Operation Notes
2. Features
3. Sender Panel Descriptions
4. Receiver Panel Descriptions
5. Connecting and Operating the HD-1000
6. Network Cable Wiring Diagram
7. Specifications
8. Warranty
The Gefen HD-1000 allows an HDMI video signal to be extended up to 330
feet (1640 w/o HDCP) using multi-mode LC-LC fiber optic cable. Fiber Optics
technology allows the HD-1000 to carry video signals over long distances that
are not possible with other technologies. Fiber Optic cables are immune to video
signal corruption from electromagnetic interference (EMI), ensuring a crystal
clear picture.
How It Works
The HD•1000S sender unit sits next to your set-top box or DVD player source.
Cables supplied with the HD•1000 connect your HDMI™ 1.3 source to the
sender unit. The display plugs into the back of the receiver unit. One CAT-5 cable
and a multi mode LC fiber optic cable connect the Sender and the Receiver units
to each other.
INTRODUCTION
1
READ THESE NOTES BEFORE INSTALLING OR
OPERATING THE HD-1000
• 50 or 62.5 micron multi-mode fiber optic cable is required for operation of
the HD-1000. Maximum extension range of 330 feet (100 meters) when
the source requires HDCP. One CAT-5, CAT-5e or CAT6 cable is used to
transmit DDC and HDCP data back to the source.
• Maximum range of 1640 feet (500 meters) when the source does not require
HDCP. This scenario does not require the CAT-5, CAT5e or CAT-6 cable if
the source does not require DDC information. If DDC is required, the use of
an EDID storage device (part# EXT-DVI-EDIDN, EXT-DVI-EDIDP) can be
used to transmit DDC information back to the source.
• HDMI 1.3 compliant (please see FEATURES section on page 2 for
supported HDMI 1.3 features).
• HDCP compliant
• Compatible with all HDMI and DVI* displays.
NOTE: *When used with a DVI to HDMI adapter
OPERATION NOTES
FEATURES
Features
• Extends high definition HDMI compliant devices up to 330 feet (100 meters)
• Uses a 4 strand multi mode LC-LC fiber optic cable for HDMI and a CAT5e cable for
DDC/control signals
• Extends range of HDMI by equalizing signals
• HDCP and HDMI compliant
• Supports resolutions up to 1080p, 2K, and 1920 x 1200
Supported HDMI Features:
• Resolutions up to 1080P Full HD
• 12 bit Deep Color
• LCPM 7.1 Audio, Dolby® TrueHD, and DTS-HD MasterAudio™
• 3DTV Pass-through
• CEC Pass-through
• Lip Sync Pass-through
Includes:
(1) HD-1000S Sender unit
(1) HD-1000R Receiver unit
(2) 5V DC Power Supply
(1) Rack Ears
(1) 6 ft HDMI cable (M-M)
(1) User’s Manual
2
SENDER PANEL DESCRIPTIONS
Back Panel
Front Panel
Power LED
Indicator
RJ-45
Port
HDMI Input
Port
Fiber Optic
LC-LC Terminals
Status LED
Indicator
5V DC
Power Input
3
RECEIVER PANEL DESCRIPTIONS
Back Panel
Front Panel
Power LED
Indicator
RJ-45
Port HDMI
Output
Port Fiber Optic
LC-LC Terminals
Status LED
Indicator
5V DC
Power Input
4
CONNECTING AND OPERATING THE HD-1000
How To Connect The HD-1000
1. Connect the HDMI source to the HD-1000 sender unit using the supplied HDMI
cable.
2. Connect a user supplied CAT-5, CAT-5e or CAT-6 cable to the sender unit.
3. Connect four user supplied multi-mode LC terminated fiber optic cables into
HD-1000 sender unit.
NOTE: 50 or 62.5 micron multi-mode fiber optic cable is required for operation of
the HD-1000.
4. Connect the other end of the CAT-5, CAT-5e or CAT-6 cable into the HD-
1000 receiver unit.
5. Connect the other ends of all four multi-mode LC terminated fiber optic
cables into the HD-1000 receiver unit.
NOTE: Please take careful note of the labeling above each fiber optic port on
both the sending and receiving HD-1000 units. The most common user error is
to mis-match the fiber optic cable connections on each end, which results in no
video being transmitted.
6. Connect the display to the HD-1000 receiver unit using a user supplied
HDMI cable.
7. Connect the included 5V DC power supplies into both the HD-1000 sending
unit and receiving units.
8. Power on the display, followed by the source.
No further adjustments are necessary to operate the HD-1000.
5
NETWORK CABLE WIRING DIAGRAM
Gefen has specifically engineered their products to work with the TIA/EIA-568-B
specification. Please adhere to the table above when field terminating cable for
use with Gefen products. Failure to do so may produce unexpected results and
reduced performance.
CAT-5, CAT-5e, and CAT-6 cabling comes in stranded and solid core types.
Gefen recommends using solid core cabling. CAT-6 cable is also recommended
for best results.
Each cable run must be one continuous run from one end to the other. No
splices or use of punch down blocks are permitted as these will cause signal
degradation.
6
EXT-HD-1000
Sender
Receiver
Hi-Def Source
HD Display
HDMI CABLE
CAT-5 CABLE
4X FIBER OPTIC LC-LC CABLE
(Up To 330 FT w/HDCP)
(Up To 1,640 FT w/HDCP)
Maximum Pixel Clock....... ....................................................................... 225 MHz
Input Video Signal .................................................................................... 1.2V p-p
Input DDC Signal .............................................................................. 5V p-p (TTL)
Single Link Range ............................................................ 1080p, 2k, 1920 x 1200
HDMI Connector .................................................................. Type A, 19 pin female
Video Link Connector .................................................................................. LC X 4
DDC Link Connector ...................................................................... RJ-45 Shielded
Power Supply ................................................................................ 5V DC, Locking
Power Consumption ..............................................................10W each unit (max)
Link Connectors ................................................... LC Fiber (4), Shielded RJ-45(1)
Rack mountable .......................................................................... 1U half-rack size
Dimensions ....................................................................... 8.5” W x 1.8” H x 4.4” D
Shipping Weight ............................................................................................ 5 lbs.
SPECIFICATIONS
7
Inhaltsverzeichnis
Andere Gefen Extender Handbücher
Gefen
Gefen EXT-DVI-2CAT6DL Bedienungsanleitung
Gefen
Gefen EXT-FW-1394BP Bedienungsanleitung
Gefen
Gefen DVI-100 Bedienungsanleitung
Gefen
Gefen EXT-VGAKVM-LAN Bedienungsanleitung
Gefen
Gefen Toolbox GTB-HDMI-3DTV Bedienungsanleitung
Gefen
Gefen GTV-WIRELESSHD Bedienungsanleitung
Gefen
Gefen CAT5-7000HD Bedienungsanleitung
Gefen
Gefen EXT-VGARS232-141 Bedienungsanleitung
Gefen
Gefen EXT-HDMI1.3-1FO Bedienungsanleitung
Gefen
Gefen EXT-DVI-CP-FM10 Bedienungsanleitung
Gefen
Gefen CAT5-5000HD Bedienungsanleitung
Gefen
Gefen HDMI CAT-5 IR Bedienungsanleitung
Gefen
Gefen EXT-DVI Audio-Cat5 Bedienungsanleitung
Gefen
Gefen EXT-DVI-1CAT6-GI Bedienungsanleitung
Gefen
Gefen CAT5-7500 Bedienungsanleitung
Gefen
Gefen ToolBox GTB-USB2.0-4LR Bedienungsanleitung
Gefen
Gefen Extender DVI 1600HD Bedienungsanleitung
Gefen
Gefen RS-232 Bedienungsanleitung
Gefen
Gefen HDMI-CAT5-MS Bedienungsanleitung
Gefen
Gefen EXT-DVIRS232-CAT5N Bedienungsanleitung
