gefran R-ETH100 Bedienungsanleitung
R-ETH100
BRIDGE ETHERNET 100 MODULE
cod. 80127C / Edit 04 -08/2011 -ENG
INSTALLATION AND OPERATION MANUAL
2 • INSTALLATION AND CONNECTION
This section contains the instructions necessary for correct
installation of the GILOGIK II into the machine control panel
or the host system and for correct connection of the system
power supply, inputs, outputs and interfaces.
Before proceeding with installation read the following
warnings carefully!
Remember that lack of observation of these warnings
could lead to problems of electrical safety and electroma-
gnetic compatibility, as well as invalidating the warranty.
Qualified staff
the installation and use of the system and components are only reserved
at qualified staff.
Conform use
the system and relative components are usable exclusively to the use
previewed in the manual
In order to guarantee a correct and sure operation are indispensable that
the product comes transported, stored correctly, installed, and controlled
second the previewed modalities.
Suitable for use in pollution degree 2 environment.
Open type equipment.
Electrical power supply
• theGILOGIKIIisNOTequippedwithanOn/Offswitch:theusermust
provide a two-phase disconnecting switch that conforms to the required
safety standards (CE marking), to cut off the power supply upstream of
thesystem.Theswitchmustbelocatedinthevicinityofthesystemand
must be within easy reach of the operator.
One switch may control more than one systems.
• Tomakesurethatthesystemveryisconnectedtoearthsecondthe
detailed lists of the relative understood one it.
• ifthesystemisusedinapplicationswithriskofdamagetopersons,
machinery or materials, it is essential to connect it up to auxiliary security
equipment. It is advisable to make sure that alarm signals are also
triggered during normal operation.
ThedispositifmustNOTbeinstalledinflammableorexplosive
environments; it may be connected to equipment operating in such
atmospheres only by means of appropriate and adequate types of
interface, conforming to the applicable safety standards
Notes Concerning Electrical Safety and Electromagnetic
Compatibility:
• CE MARKING: EMC Conformity (electromagnetic compatibility)
in accordance with EEC Directive 2004/108/CE.
TheGILOGIKIIsystemismainlydesignedtooperatein
industrial environments, installed on the switchboards or control panels
of productive process machines or plants.
Normofapplicableproduct:EN61131-2.
TheDeclarationofconformityisavailableonGEFRANweb:www.gefran.
com
•UL listed standard:UL508fileE198546
• BT Conformity (low tension)
inaccordancewithDirectiveLVD2006/95/CE.
AdviceforCorrectInstallationforEMC
Module power supply
• Supplywithclass2device
• Thepowersupplytothemodulesontheswitchboardsmustalways
come directly from an isolation device with a fuse.
• Theelectronicinstrumentsandelectromechanicalpowerdevices
such as relays, contactors, solenoid valves, etc., must always be
powered by separate lines.
• Whenthepowersupplyisstronglydisturbedbythecommutationof
transistor or power units or motors, an isolation transformer should
be
used, earthing the screen.
• Itisessentialthattheplanthasagoodearthconnection:
-thevoltagebetweenneutralandearthmustnotbe>1V
-theOhmicresistancemustbe<6Ω;
• Intheproximityofhighfrequencygeneratorsorarcwelders,use
adequate filters.
• Thepowersupplylinesmustbeseparatefromtheinstrumentinput
and output ones.
GEFRAN S.p.A. declines all responsibility for any damage
to persons or property caused by tampering, neglect,
improper use or any use which does not conform to the
characteristics of the controller and to the indications
given in these Instructions for Use.
I1 • MAIN FEATURES
• CompletecontrolofR-BUS(x)backplane
• RefreshofallinstalledI/Osin100us(1node)
• GDNetinterface
• Powersupplyofbackplane
3
80127C_MHW_R-ETH100_08-2011_ENG
I3 • TECHNICAL DATA
Power supply
- Supply with class 2 device
-24VDC±25%2Amax.,powerstheentireGILOGIKIIsystem
- polarity inversion protection
Ethernet
-standardRJ45connection
-16positionrotaryswitchfornodeidentificationonnetworkconfiguration
-StandardIEEE802.3
Diagnostics
-powersupplyon(yellowPOWERled)
-moduleinrun/configuration(greenRUNled)
-moduleorsysteminalarm/notconfigurated(redFAILled)
-yellowLINKled:networkconnected
-greenDATAled:datatransfer
Mechanical data
Dimensions:92x90x25,4mm
Weigth:150g.
Fixing:snapsontoR-BUS(x)
Protectionlevel:IP20
aMbient conditions
Working Temperature:0...50°C
Storage Temperature:-20...70°C
Humidity:max.90%Rhnotcondensing
For UL:Maximumsurroundingairtemperature50°C
4 • CONNECTIONS
ThemoduleinstallsonR-BUS(x)inthefirstslotontheleftifthereisnoR-SW5module;
inthesecondslotifthereisanR-SW5module.
(*) with the 18 position bus, positions 1, 2 are reserved
totheR-ETH100andR-SW5modules.
(*)
480127C_MHW_R-ETH100_08-2011_ENG
GEFRAN spaviaSebina,74-25050Provagliod’Iseo(BS)
Tel.03098881-fax0309839063-Internet:http://www.gefran.com
YellowLEDPOWER
GreenLEDRUN
RedLEDFAIL
GreenLEDDATA
YellowLEDLINK
Ethernet (*)
Supply (**)
RJ45
0 = no active
1..F=nodo1..F(1..15)
24Vdc
±25%
Max2A
(*)Usestandardcategory6cableaccordingtoTIA/EIA-568A
(**)Useunipolarcablewith1-1.5mmcrosssectionDonotattachalug
Rotaryswitchtoselectthenode
Inhaltsverzeichnis
Andere gefran Netzwerk-Router Handbücher
Beliebte Netzwerk-Router Handbücher anderer Marken
NETGEAR
NETGEAR FS526T - Switch Bedienungsanleitung
Korenix
Korenix JetNet 5710G Series Bedienungsanleitung
Automated Logic
Automated Logic ZN551 Betriebsanleitung
Cisco
Cisco ASR 1000 Series Bedienerhandbuch
EnGenius
EnGenius ESR-9710 Bedienungsanleitung
Cisco
Cisco 805 Series Bedienungs- und Sicherheitshinweise